Page 548 of 3039
Installation
3. Special Tool(s): 204-335
1. NOTE: Make sure the new bushes are installed in the correct
orientation.
.
Special Tool(s): 204-275, 204-601, 303-1121, 204-274
2. Refer to: Differential Case - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-02 Rear Drive Axle/Differential, Removal and Installation). www.JagDocs.com
Page 554 of 3039
Rear Drive Axle/Differential - Differential Locking Motor
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 26-Feb-2014
1. Refer to: Differential Draining and Filling (205-02 Rear Drive Axle/Differential, General Procedures).
2.
3.
Page 560 of 3039
Rear Drive Halfshafts -
Lubricants, Fluids, Sealers and Adhesives Published: 11-May-2011
Item Specification Constant velocity (CV) grease Optimal LN 584 LO Fill Capacities
Description Grams Grease for inner CV joint - all vehicles 140 Grease for outer CV joint - all vehicles 125 Torque Specifcations
NOTE: Make sure that a new nut is installed.
Item Nm lb-ft lb-in Halfshaft outer constant velocity joint retaining nut 300 221 -
Page 561 of 3039
Published: 11-May-2011
Rear Drive Halfshafts - Rear Drive Halfshafts - Component Location
Description and Operation
Component Location
Item Description 1 Outer constant velocity joint 2 Outer constant velocity joint gaiter 3 Left hand halfshaft 4 Inner constant velocity joint gaiter 5 Inner constant velocity joint 6 Right hand halfshaft
Page 562 of 3039
Rear Drive Halfshafts - Rear Drive Halfshafts - Overview
Description and Operation
Overview Published: 11-May-2011
The CV (constant velocity) joint at each end of the halfshafts meets the angle change requirements due to suspension
deflection. The plunge capability of the CV joint accommodates the length change.
Page 563 of 3039
Published: 11-May-2011
Rear Drive Halfshafts - Rear Drive Halfshafts - System Operation and
Component Description
Description and Operation
System Operation
Rear Drive Halfshafts Component Description
The solid-steel halfshafts are of unequal length, with each halfshaft comprising inner and outer CV (constant velocity) joints.
The CV joints are the 'ball and socket' type packed with grease and protected by gaiters.
The outer CV joint is an interference fit into the wheel hub and secured by a locking nut. The inner CV joint is a slide fit and is
retained in the differential with a spring clip.
www.JagDocs.com
Page 575 of 3039
Rear Drive Halfshafts - Inner Constant Velocity (CV) Joint Boot
Removal and Installation
Removal Published: 11-May-2011
1. WARNING: Do not work on or under a vehicle supported only by a
jack. Always support the vehicle on safety stands.
Raise and support the vehicle.
2. Remove the rear halfshaft.
For additional information, refer to: Rear Halfshaft - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-05 Rear Drive Halfshafts, Removal and Installation).
3. CAUTION: Use suitable protective covers to protect the halfshaft.
Using a suitable clamp, secure the rear halfshaft.
4. CAUTION: Make sure the inner constant velocity (CV)
joint is not separated from the halfshaft.
Remove and discard the inner CV joint boot retaining clip.
5. CAUTION: Make sure the CV joint ball bearings do not
drop out of the CV joint.
Using a suitable tool, remove the inner CV joint. www.JagDocs.com
Page 578 of 3039
/V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-05 Rear Drive Halfshafts, Removal and Installation).
