2010 JAGUAR XFR belt

Fuel Charging and Controls - V8 S/C 5.0L Petrol -
WARNINGS: Published: 11-May-2011

Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components.
Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.


Before any work is carried out on the fuel system, ground the vehicle to earth and maintain the ground connection until
the work is complete.


CAUTION: Before disconnecting or removing components, make sure the area around the joint faces and connections are
clean. Plug open connections to prevent contamination.


NOTE: Tighten the fuel rail high pressure fuel pump fuel line unions and fuel rail crossover pipe unions as it is instructed
in service manual.

Description Nm lb-ft lb-in Ignition coil-on-plugs retaining bolts 7 - 62 Spark plugs 20 15 - Fuel rail retaining bolt Stage 1 - 20 Stage 2 - 30 Stage 1 - 15 Stage 2 - 22 - Fuel rail crossover pipe unions 21 15 - Fuel rail crossover pipe retaining bolts 12 9 - Fuel pressure regulator 33 24 - Fuel rail high pressure fuel pump fuel line unions 21 15 - Fuel rail high pressure fuel pump fuel line M8 bolt 25 18 - Fuel rail high pressure fuel pump fuel line M6 bolt 11 8 - Fuel rail high pressure fuel pump fuel line M5 nut 6 - 53 Fuel rail high pressure fuel pump fuel line shield M10 bolt 29 21 - Fuel rail high-pressure fuel pump fuel line shield M6 bolt 11 8 - Fuel rail high pressure fuel pump torx bolts 12 9 - Throttle body retaining bolts 10 7 - Accessory drive belt idler pulley retaining bolts 25 18 - Steering gear retaining bolts 100 74 - Steering column lower universal joint assembly bolts 35 26 - Coolant expansion tank retaining bolt 10 7 - Engine compartment brace retaining bolts 45 33 - www.JagDocs.com

Accessory drive belt tensioner retaining bolt 40 30 - Accessory drive belt idler pulley retaining bolt - all vehicles 40 30 - Accessory drive belt center idler pulley retaining bolt - vehicles without supercharger 25 19 - Accessory drive belt idler pulley retaining bolt to tensioner bracket - vehicles with supercharger 40 30 - Supercharger belt tensioner bracket retaining bolt 25 19 - Supercharger belt tensioner retaining bolt 40 30 - Supercharger belt 76mm idler pulley retaining bolt 40 30 - Supercharger belt 90mm idler pulley retaining bolt 56 41 -

Published: 11-May-2011
Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive - Component Location
Description and Operation
COMPONENT LOCATION










































Item Description A Primary accessory drive B Secondary accessory drive 1 Coolant pump 2 Power steering pump 3 Primary drive belt 4 A/C (air conditioning) compressor 5 Belt tensioner 6 Crankshaft pulley/torsional vibration damper 7 Idler pulley

9 Idler pulley 10 Supercharger 11 Idler pulley 12 Belt tensioner 13 Secondary drive belt 14 Idler pulley www.JagDocs.com

Published: 11-May-2011
Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive - Overview
Description and Operation

OVERVIEW

The accessory drive is a belt system powered by a pulley attached to the front of the crankshaft. The crankshaft pulley, which
incorporates a torsional vibration damper, drives two drive belts. An automatic belt tensioner in each belt run maintains the
drive belt at the correct tension. Together with idler pulleys, the belt tensioners also guide the drive belts clear of obstructions
and set the correct 'wrap-around' of the accessory component drive pulleys to ensure a slip-free drive.

PRIMARY DRIVE BELT
The primary drive belt is a six-ribbed poly-V belt that drives the:
Coolant pump
Power steering pump
A/C (air conditioning) compressor
Generator.

SECONDARY DRIVE BELT

The secondary drive belt is an eight-ribbed poly-V belt that drives the SC (supercharger).

BELT TENSIONERS

Each belt tensioner consists of an idler pulley on the end of a spring loaded pivot arm. The pivot arms can be turned manually
for removal and installation of the drive belts.
Each belt tensioners is calibrated to automatically maintain the correct tension in the related drive belt.

Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive Belt
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger Belt (303-05, Removal and Installation).


3. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

4. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

5. Torque: 55 Nm 6. Torque: 25 Nm

7. CAUTIONS:


Make sure that the accessory drive belt is correctly
aligned to the pulleys. Failure to follow this instruction may
result in damage to the vehicle.


Clean and inspect the accessory drive belt pulleys for
damage.
NOTES:


Some variation in the illustrations may occur, but the
essential information is always correct.


Engine shown removed for clarity.


Note the fitted position.

Installation

1. To install, reverse the removal procedure.

Published: 11-May-2011
Accessory Drive - V8 S/C 5.0L Petrol - Accessory Drive Belt Idler Pulley
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger Belt (303-05, Removal and Installation).

3. Refer to: Air Cleaner Outlet Pipe LH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).


4. NOTE: Note the fitted position.
















5. Torque: 25 Nm