2010 JAGUAR XFR torque

Installation
12.

NOTE: Do not disassemble further if the component is
removed for access only.

All vehicles

1. Torque: 45 Nm 2. CAUTION: LH illustration shown, RH is similar.

NOTE: Install a new gasket.
Install the special tool.

Special Tool(s): 303-1444-01

3. CAUTION: LH illustration shown, RH is similar.


NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Install the special tool.

Special Tool(s): 303-1444-02







4. CAUTIONS:


Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.

Torque: 10 Nm





5. CAUTION: LH illustration shown, RH is similar.
Remove the special tool.














6. CAUTIONS:


Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm www.JagDocs.com

7.
















8.
9.
10. CAUTION: LH illustration shown, RH is similar.

Torque: 18 Nm


















































Torque: 12 Nm

11. Torque: 48 Nm













Right-hand drive vehicles

12.
13.
CAUTION: Discard the bolt.

Torque: 35 Nm













Torque: 100 Nm

Engine - V8 S/C 5.0L Petrol - Flexplate
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Transmission - V8 5.0L Petrol/V8 S/C 5.0L Petrol (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal).

4. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts
with a center punch. If 2 punch marks are visible, discard
the bolts.
Make sure that no components fall off during removal.
Install the bolts in the noted position.

NOTES:


Make sure the crankshaft and flexplate mating faces
are clean before installation.


Make sure that the crankshaft is not rotated.


Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
Installation

1. To install, reverse the removal procedure.

7. CAUTIONS:


Be prepared to collect escaping oil.


Be prepared to collect escaping coolant.

Torque: 13 Nm









8. CAUTION: Make sure that these components are
installed to the noted removal position.


NOTE: Install a new gasket.

Installation
1. CAUTIONS:


Use only a plastic scraper when removing the sealing
material.


Use lint free cloth.


Make sure that the mating faces are clean and free of
corrosion and foreign material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G)
to the areas shown, and tighten the bolts within 7
minutes.
Apply a bead of sealant, 2.5 mm diameter, to the
area indicated.








2. NOTE: Tighten the bolts in the sequence shown.
Torque: 12 Nm
















3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).

Installation

1. Torque: 8 Nm 2. CAUTIONS:


Make sure that the mating faces are clean and free of foreign material.


Use only a plastic scraper when removing the sealing material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas
shown, and tighten the bolts within 7 minutes.



























3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 25 Nm