2010 JAGUAR XFR Interior

Interior Trim and Ornamentation - Parcel Shelf
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: C-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

2. Torque: 12 Nm www.JagDocs.com

Interior Trim and Ornamentation - Rear Scuff Plate Trim Panel
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 19-Dec-2012




Installation

1. CAUTIONS:


Care must be taken when releasing the trim panel
from the retaining clips.


Make sure that the clips are correctly located.

1. To install, reverse the removal procedure.

Interior Trim and Ornamentation - Sun Visor
Removal and Installation
Removal

NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011


1. CAUTION: Take extra care not to damage the edges of the
component.

































2. TORQUE: 2 Nm www.JagDocs.com

Interior Trim and Ornamentation - Sun Visor Vanity Mirror
Removal and Installation

General Equipment Published: 28-Jan-2013

Removal




Installation

1. Using a suitable tool, release the retaining clips and
remove the sun visor vanity mirror from the sun visor.

General Equipment: Interior trim remover

1. CAUTION: Do not use excessive force to install the
component.

Press firmly against the areas indicated until an audible
click is heard. Interior trim remover

Published: 11-May-2011
Exterior Trim and Ornamentation - Luggage Compartment Lid Moulding
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Luggage Compartment Lid Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

2.
3. Torque: 3 Nm 4. www.JagDocs.com

Rear View Mirrors - Rear View Mirrors - Component Location
Description and Operation


NOTE: LHD (left-hand drive) shown RHD (right-hand drive) similar Published: 11-May-2011



Item Description 1 Passenger door mirror 2 Passenger door control module 3 Interior mirror 4 Drivers door control module 5 Mirror control switch 6 Drivers door mirror

Rear View Mirrors - Rear View Mirrors - Overview
Description and Operation

Overview
The exterior mirrors incorporate the following:
Blind spot monitoring indicator
Auto dimming function
Turn signal indicators
Approach lamps
Exterior temperature sensor
Heated mirror function
Reverse dipping function Published: 11-May-2011
Movement of the door mirrors is controlled from a switch pack located on the drivers door. The switch pack contains 2
non-latching mirror select buttons labeled 'L' and 'R' and a 4-way mirror movement switch. Door mirror movement commands
are transmitted to the driver's door module over the LIN (local interconnect network) bus. The drivers door module transmits
any mirror movement commands to the passenger door module over the medium speed CAN (controller area network) bus.

Movement of the door mirrors is carried out by the respective door module. The door modules provide supply and ground paths
to the mirror motors and monitor mirror position via potentiometers located in the mirror housings.

Both exterior door mirrors and the interior mirror feature an auto dimming function. The interior rear view mirror contains one
forward and one reward facing light sensor. The light sensors control the auto dimming feature of the interior mirror to reduce
glare from the headlights of following vehicles.

When auto-dimming of the interior mirror is required, a supply is provided by the interior mirror to both door mirrors to initiate
the door mirror auto-dimming sequence.

Blind spot monitoring function alerts the driver to a vehicle located in the vehicle blind spot. A warning indicator is located in
each exterior mirror towards the outer edge.
Refer to: Blindspot Monitoring System (413-09 Warning Devices, Description and Operation).

Published: 04-Nov-2013
Rear View Mirrors - Rear View Mirrors - System Operation and Component Description
Description and Operation

Control Diagram

NOTE: A = Hardwired, N = Medium speed CAN (controller area network) bus, O = LIN (local interconnect network) bus



Item Description 1 RJB (rear junction box) 2 RH (right-hand) door module 3 RH door mirror 4 LH (left-hand)side door mirror 5 Interior mirror 6 Battery