2010 INFINITI QX56 turn signal

AV-28
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “SETTING” button, turn the volume control
dial counterclockwise 30 clicks or more.
CONFIRMATION/
ADJUSTMENT Display diagnosis
Color spectrum bar Color tone of the screen can be checked by the display of a color bar.
Gradation bar Shading of the screen can be checked by the display of a gray scale.
Touch panel
• Touch panel calibration
• Touch panel response check
Vehicle signals The following vehicle signals are analyzed: Vehicle speed signal, park-
ing brake signal, light signal, ignition switch signal, and reverse signal.
Speaker test Connection can be checked by sending a test tone to each speaker.
Navigation Steering angle ad-
justment
Confirm/adjust the steering angle when there is a difference between
the displayed vehicle mark turning angle and actual.
Speed calibration Confirm/adjust the speed calibration when there is a difference between
the displayed vehicle mark location and actual.
XM SAT subscrip-
tion status Check the subscription status of the XM NAV Traffic subsription.
Error history Diagnosis results previously stored in the memory are displayed in this
mode.
Synchronize FES clock Turns FES (Familly Entertainment System) clock synchronization func-
tion ON/OFF.
Vehicle CAN diagnosis The transmitting/receiving of CAN communication can be monitored.
AV COMM diagnosis The transmitting/receiving of AV communication can be monitored.
Handsfree phone Handsfree volume
adjustment
Adjust handsfree volume (low, medium, high).
Voice microphone
test Test microphone operation.
Delete handsfree
memory Erase handsfree system memory.
Bluetooth Confirm/Change
passkey
Confirm and change the Bluetooth passkey
Confirm/Change
device name Confirm and change a device name stored in Bluetooth.
SAT Change channel
Any necessary channels required to recieve traffic information from the
satellite radio system can be set.
Change applica-
tion ID Any application ID’s required to recieve traffic information from the sat-
ellite radio system can be set.
Diag Not used.
Delete unit connection log Erase the error history and connection history of the unit.
Initialize settings All audio settings are reset to default levels.
Mode
Description
ALNIA0446GB
Revision: April 20092010 QX56

AV-40
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DATA MONITOR
Display Item List
A/C AND AV SWITCH ASSEMBLY
A/C AND AV SWITCH ASSEMBLY : Component Function CheckINFOID:0000000005146244
A/C and AV switch assembly self-diagnosis function
Description
The ON/OFF operation (continuity) of
each switch in the A/C and AV switch assembly can be checked.
Self-diagnosis mode
• Press the “BACK” button and the “UP” button within 10 seconds
after turning the ignition switch from OFF to ACC and hold them for
3 seconds or more. When the self-diagnosis mode starts, a beep
will sound and all LED indicators of the switch will illuminate.
• The continuity of each switch and control dial of the A/C and AV switch assembly can be checked. If the switch is operating nor-
mally, the system will beep and the LED’s will illuminate when each
switch is operated.
Finishing self-diagnosis mode
Self-diagnosis mode is canceled when the ignition switch is turned OFF.
• AV COMM CIRCUIT [U1300]
• REAR CAMERA LAN CONN [U1252] • A malfunction is detected in camera con-
trol unit power supply and ground cir-
cuits.
• Malfunction is detected on AV communi- cation signal between Camera control
unit and AV control unit. Camera control unit power supply and
ground circuits. Refer to
AV- 7 2 , "REAR
VIEW CAMERA CONTROL UNIT : Diagno-
sis Procedure".
• AV COMM CIRCUIT [U1300]
• CAMERA CONT. CONN [U1250]
• REAR CAMERA LAN CONN [U1252] • Malfunction is detected on AV communi-
cation circuit between camera control
unit and AV control unit.
• Malfunction is detected on AV communi- cation signal between camera control
unit and AV control unit. AV communication circuit between camera
control unit and AV control unit. Refer to
AV-
11 0 , "Reference Value".
Error item Description Possible malfunction factor/Action to take
Display item [unit]
ALL
SIGNALS SELECTION
FROM MENU Description
VHCL SPD SIG [ON/OFF] X XDisplays “ON” when vehicle speed > 0 km/h. Displays “OFF” when ve-
hicle speed = 0 km/h.
PKB SIG [ON/OFF] XX Displays [ON/OFF] condition of parking brake switch.
ILLUM SIG [ON/OFF] XX Displays [ON/OFF] condition of lighting switch.
IGN SIG [ON/OFF] XX Displays [ON/OFF] condition of ignition switch.
REV SIG [ON/OFF] XX Displays [ON/OFF] condition of back-up lamp switch.
AWIIA0171GB
Revision: April 20092010 QX56

AV
U1000 CAN COMM CIRCUITAV-41
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000005146245
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each
control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-44, "
CAN Communication Signal Chart".
DTC LogicINFOID:0000000005146246
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005146247
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of “AV Control Unit”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to “LAN system”. Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI section. Refer to GI-38, "
Intermittent Incident".
DTCDisplay contents of CON-
SULT-III Diagnostic item is detected when ...
Probable malfunction location
U1000 CAN COMM CIRCUIT When AV control unit is not transmitting or re-
ceiving CAN communication signal for 2 sec-
onds or more. CAN communication system.
Revision: April 20092010 QX56

AV-60
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1243 DISPLAY UNIT
U1243 DISPLAY UNIT
DescriptionINFOID:0000000005146286
DTC LogicINFOID:0000000005146287
Diagnosis ProcedureINFOID:0000000005146288
Regarding Wiring Diagram information, refer to
AV-116, "Wiring Diagram".
1.CHECK DISPLAY UNIT POWER SUPPLY AND GROUND CIRCUIT
Check display unit power supply and ground circuit. Refer to AV-69, "
DISPLAY UNIT : Diagnosis Procedure".
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair malfunctioning parts.
2.CHECK CONTINUITY CO MMUNICATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector M93 and AV control unit connector M43.
3. Check continuity between display unit harness connector M93 (A) terminals 11, 22 and AV control unit harness connector M43
(B) terminals 30, 31.
4. Check continuity between display unit harness connector M93 (A) terminals 11, 22 and ground.
Part name Description
DISPLAY UNIT • Display image is controlled by the serial communication from AV control unit.
• RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing). Auxiliary image signal is input from the auxiliary input jack. Cam-
era image signal is input from the camera control unit.
• Synchronize signal (HP, VP) is output to AV control unit.
• Touch panel function can be operated for each system by touching a display directly.
DTC Display contents of
CONSULT-III DTC Detection Condition
Possible causes
U1243 FRONT DISP CONN
[U1243] • Display unit power supply and ground circuit malfunc-
tion is detected.
• Malfunction is detected on communication circuit be- tween display unit and AV control unit.
• Malfunction is detected on communication signal be-
tween display unit and AV control unit. • Display unit power supply and
ground circuit.
• Communication circuit between display unit and AV control unit.
AB Continuity
Connector Terminal Connector Terminal
M93 11
M43 30
Ye s
22 31
A —Contin u it y
Connector Terminal
M93 11
Ground No
22
ALNIA0397GB
Revision: April 20092010 QX56

AV
U1243 DISPLAY UNITAV-61
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
Are continuity results as specified?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK COMMUNICATION SIGNAL
1. Connect display unit connector M93 and AV control unit connec-
tor M43.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector M93 ter- minal 11 and ground.
Are voltage readings as specified?
YES >> GO TO 4.
NO >> Replace AV control unit. Refer to AV-169, "
Removal and Installation".
4.CHECK COMMUNICATION SIGNAL
Check signal between display unit harness connector M93 terminal
22 and ground.
Are voltage readings as specified?
YES >> Inspection end.
NO >> Replace display unit. Refer to AV-171, "
Removal and Installation".
Connector Te r m i n a l s
Reference Signal
(+) (-)
M93 11 Ground
ALNIA0398GB
PKIB5039J
Connector Te r m i n a l s
Reference Signal
(+) (-)
M93 22 Ground
ALNIA0399GB
PKIB5039J
Revision: April 20092010 QX56

AV-62
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1244 GPS ANTENNA
U1244 GPS ANTENNA
DescriptionINFOID:0000000005146289
DTC LogicINFOID:0000000005146290
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005146291
Regarding Wiring Diagram information, refer to
AV-116, "Wiring Diagram".
1.GPS ANTENNA CHECK
Inspect GPS antenna and antenna feeder for damage or poor connection.
Is the GPS antenna and feeder clean and undamaged?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
2.CHECK AV CONTROL UNIT VOLTAGE
1. Turn ignition switch ON.
2. Check voltage between AV control unit connector M124 terminal 116 and ground.
Is the voltage reading as specified?
YES >> Replace GPS antenna. Refer to AV-186, "Removal and
Installation".
NO >> Replace AV control unit. Refer to AV-169, "
Removal and
Installation".
Part Name Description
GPS ANTENNA GPS signal is detected and transmitted to the AV control unit.
DTC CONSULT-III display Detection condition
U1244 GPS ANTENNA CONN
[U1244]
GPS antenna connection malfunction is detected.
116 - Ground
: Approx. 5V
ALNIA0400GB
Revision: April 20092010 QX56

AV
U1258 SATELLITE RADIO ANTENNAAV-65
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
U1258 SATELLITE RADIO ANTENNA
DescriptionINFOID:0000000005146295
DTC LogicINFOID:0000000005146296
Diagnosis ProcedureINFOID:0000000005146297
Regarding Wiring Diagram information, refer to AV-116, "Wiring Diagram".
1.SATELLITE RADIO ANTENNA CHECK
Visually check satellite radio antenna and antenna feeder.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair malfunctioning parts.
2.CHECK AV CONTROL UNIT VOLTAGE
1. Disconnect AV control unit connector M125.
2. Turn ignition switch ON.
3. Check voltage between AV control unit connector M125 termi- nal 118 and ground.
Is voltage approximately 5 volts?
YES >> Inspection end.
NO >> Replace AV control unit. Refer to AV-169, "
Removal and
Installation".
Part name Description
SATELLITE RADIO ANTENNA Satellite radio signal is received and sent to audio control unit.
DTCDisplay contents of
CONSULT-III DTC Detection Condit
ion Possible causes
U1258 XM ANETNNA CONN
[U1258] Satellite radio antenna connection malfunction is detect-
ed.
Satellite radio antenna disconnection.
118 - Ground
: Approx. 5 V
ALNIA0403GB
Revision: April 20092010 QX56

AV
POWER SUPPLY AND GROUND CIRCUITAV-69
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
1. Ignition OFF.
2. Check continuity between AV control unit harness connectors M42 and M45 and ground.
Are the continuity results as specified?
YES >> Inspection End.
NO >> Repair AV control unit ground.
DISPLAY UNIT
DISPLAY UNIT : Diagnosis ProcedureINFOID:0000000005146302
Regarding Wiring Diagram information, refer to AV-116, "Wiring Diagram".
1.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch to ACC
2. Check voltage between display unit harness connector M93 and ground.
Does specified voltage exist?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector.
3. Check continuity between display unit harness connector M93 and ground.
Does continuity exist?
YES >> Inspection end.
Connector (+)
(-)Continuity
Te r m i n a l
M42 20
Ground Yes
M45 65
67
86
87
AWNIA1555ZZ
Signal name Connector Terminal
Ignition switch
position Value (Approx.)
B+ M932
ACC Battery voltage
ACC 3
ALNIA0317GB
(+)
(-)Continuity
Connector Terminal
M93 1
Ground Yes
13
ALNIA0407GB
Revision: April 20092010 QX56