2009 SUBARU TRIBECA Intake

5AT-34
Automatic Transmission Assembly
AUTOMATIC TRANSMISSION
9. Automatic Transmission As-
sembly
A: REMOVAL
1) Set the vehicle on a lift.
2) Open the front hood and support with the hood
stay.
3) Disconnect the ground cable from battery.
4) Remove the collector cover.
5) Remove the air intake chamber. IN(H6DO)-6, REMOVAL, Air Intake Chamber.>
6) Remove the air breather hose. REMOVAL, Air Breather Hose.>
7) Remove the starter. MOVAL, Starter.>
8) Disconnect the front oxygen (A/F) sensor and
transmission harness connector.
9) Disconnect the engine harness connectors, and
then remove the engine hanger rear.
10) Remove the vacuum pipe & hose assembly
and the brake vacuum pump. MOVAL, Brake Vacuum Pump.>
11) Remove the throttle body securing bolts to and
slide the throttle body over.
12) Separate the torque converter from drive plate.
(1) Remove the service hole plug.
(2) Remove the bolts which hold torque con-
verter to drive plate.
(3) Remove the four bolts by rotating the clamp
pulley a little at a time.
(4) Make sure the torque converter moves free-
ly by rotating with finger through the starter in-
stallation hole.
CAUTION:
Be careful not to drop bolts into converter
housing.
13) Install the ST to the converter case.
ST 498277200 STOPPER SET
14) Remove the pitching stopper.
(A) Front oxygen (A/F) sensor
(B) Transmission harness connectors
(A) Engine harness connectors
(B) Engine hanger rear
(A)
(B)
AT-03239
(B)
(A)
(A)
AT-02023
AT-01366
AT-00103
ST
AT-03240

5AT-40
Automatic Transmission Assembly
AUTOMATIC TRANSMISSION
34) Install the engine hanger rear, and then con-
nect the engine harness connector.
35) Pour ATF from the oil charge pipe. 5AT-26, REPLACEMENT, Automatic Transmis-
sion Fluid.>
36) Install the air breather hose. INSTALLATION, Air Breather Hose.>
37) Install the throttle body to intake manifold.
Tightening torque:
8 N·m (0.8 kgf-m, 5.9 ft-lb)
38) Install the air intake chamber. IN(H6DO)-6, INSTALLATION, Air Intake Cham-
ber.>
39) Install the collector cover.
40) Connect the ground cable to the battery.
41) Perform Clear Memory 2 operation. 5AT(diag)-17, CLEAR MEMORY MODE, OPERA-
TION, Subaru Select Monitor.>
42) Perform the inspection with driving the vehicle
at the end of repair work, and make sure there is no
faulty as below;
•Excessive shift shock
•Oil leakage from the transmission body, etc.
•Occurrence of noise caused by interference etc.
NOTE:
If excessive shift shock is felt, execute advance op-
eration of learning control. PROCEDURE, Learning Control.>
(A) Engine harness connectors
(B) Engine hanger rear
(B)
(A)
(A)
AT-02023

5AT-41
Transmission Mounting System
AUTOMATIC TRANSMISSION
10.Transmission Mounting Sys-
tem
A: REMOVAL
1. PITCHING STOPPER
1) Disconnect the ground cable from battery.
2) Remove the air intake chamber. IN(H6DO)-6, REMOVAL, Air Intake Chamber.>
3) Remove the pitching stopper.
2. TRANSMISSION REAR CROSSMEMBER
& REAR CUSHION RUBBER
1) Disconnect the ground cable from battery.
2) Jack–up the vehicle and support it with rigid
racks.
3) Remove the front exhaust pipe, rear exhaust
pipe and muffler. AL, Front Exhaust Pipe.> REMOVAL, Rear Exhaust Pipe.> EX(H6DO)-8, REMOVAL, Muffler.>
4) Remove the heat shield cover.
5) Set the transmission jack under transmission.
Make sure that the support plate of transmission
jack does not touch the oil pan.
6) Remove the transmission rear crossmember.
7) Remove the rear cushion rubber from transmis-
sion.
B: INSTALLATION
1. PITCHING STOPPER
1) Attach the pitching stopper.
Tightening torque:
T1: 50 N·m (5.1 kgf-m, 36.9 ft-lb)
T2: 58 N·m (5.9 kgf-m, 42.8 ft-lb)
2) Install the air intake chamber. 6, INSTALLATION, Air Intake Chamber.>
3) Connect the ground cable to the battery.
2. TRANSMISSION REAR CROSSMEMBER
& REAR CUSHION RUBBER
1) Install the rear cushion rubber to the transmis-
sion.
Tightening torque:
40 N·m (4.1 kgf-m, 29.5 ft-lb)
2) Attach the cross member to the rear cushion
rubber.
Tightening torque:
35 N·m (3.6 kgf-m, 26 ft-lb)
3) Install the cross.
Tightening torque:
75 N·m (7.6 kgf-m, 55.3 ft-lb)
AT-03245
AT-01377
AT-03250
T2
T1
AT-01377

5AT-49
Rear Vehicle Speed Sensor
AUTOMATIC TRANSMISSION
15.Rear Vehicle Speed Sensor
A: REMOVAL
1) Set the vehicle on a lift.
2) Disconnect the ground cable from battery.
3) Remove the air intake chamber. IN(H6DO)-6, REMOVAL, Air Intake Chamber.>
4) Disconnect the front oxygen (A/F) sensor and
transmission harness connector.
5) Remove the transmission harness connector
and front oxygen (A/F) sensor connector from the
stay.
6) Lift-up the vehicle.
7) Clean the transmission exterior.
8) Drain the ATF completely. PLACEMENT, Automatic Transmission Fluid.>
9) Remove the rear exhaust pipe and muffler.
Pipe.>
10) Remove the heat shield cover.
11) Remove the propeller shaft. REMOVAL, Propeller Shaft.>
12) Place the transmission jack under the transmis-
sion.
NOTE:
Make sure that the support plate of transmission
jack does not touch the cross.
13) Remove the transmission rear crossmember
bolt.
14) Lower the transmission jack.
NOTE:
Do not separate the transmission jack and trans-
mission.
15) Remove the oil charge pipe. REMOVAL, Oil Charge Pipe.>
16) Remove the ATF cooler inlet and outlet pipes.
NOTE:
When removing the outlet pipe, be careful not to
lose the ball and spring used with retaining screw.
17) Disconnect the connector from turbine speed
sensor 1.
18) Remove the rear vehicle speed sensor.
19) Remove the oil pan.
20) Disconnect the control valve connector and
front vehicle speed sensor connector.
(A) Front oxygen (A/F) sensor
(B) Transmission harness connectors
(A)
(B)
AT-03239
AT-01377
(A) Control valve connector
(B) Front vehicle speed sensor connector
AT-01387
AT-03225
AT-01956
(B)
(A)

5AT-51
Rear Vehicle Speed Sensor
AUTOMATIC TRANSMISSION
7) Install the rear vehicle speed sensor and turbine
speed sensor 1, and then fasten the harness.
Tightening torque:
7 N·m (0.7 kgf-m, 5.2 ft-lb)
8) Install a new aluminum washer and oil cooler
pipe.
Tightening torque:
40 N·m (4.1 kgf-m, 29.5 ft-lb) (ATF inlet pipe)
45 N·m (4.6 kgf-m, 33.2 ft-lb) (ATF outlet pipe)
9) Install the oil charge pipe. STALLATION, Oil Charge Pipe.>
10) Install the transmission rear crossmember bolt.
Tightening torque:
70 N·m (7.1 kgf-m, 51.6 ft-lb)
11) Install the propeller shaft. STALLATION, Propeller Shaft.>
12) Install the heat shield cover.
13) Install the rear exhaust pipe and muffler. to EX(H6DO)-7, INSTALLATION, Rear Exhaust
Pipe.> Muffler.>
14) Lower the vehicle.
15) Install the transmission connector to the stay,
and then connect the connector.
16) Install the air intake chamber. IN(H6DO)-6, INSTALLATION, Air Intake Cham-
ber.>
17) Pour ATF from the oil charge pipe. 5AT-26, REPLACEMENT, Automatic Transmis-
sion Fluid.>
18) Check the level and leaks of ATF. 26, INSPECTION, Automatic Transmission Fluid.>

5AT-52
Turbine Speed Sensor 1
AUTOMATIC TRANSMISSION
16.Turbine Speed Sensor 1
A: REMOVAL
1) Remove the air intake chamber. IN(H6DO)-6, REMOVAL, Air Intake Chamber.>
2) Lift-up the vehicle.
3) Disconnect the turbine speed sensor 1 connec-
tor.
4) Remove the turbine speed sensor 1.
B: INSTALLATION
1) Install the turbine speed sensor 1.
Tightening torque:
7 N·m (0.7 kgf-m, 5.2 ft-lb)
2) Connect the turbine speed sensor 1 connector.
3) Lower the vehicle.
4) Install the air intake chamber. IN(H6DO)-6, INSTALLATION, Air Intake Cham-
ber.>
AT-01387
AT-01387

5AT-60
Air Breather Hose
AUTOMATIC TRANSMISSION
21.Air Breather Hose
A: REMOVAL
1) Remove the air intake chamber. IN(H6DO)-6, REMOVAL, Air Intake Chamber.>
2) Disconnect the air breather hose.
B: INSTALLATION
1) Connect the air breather hose.
2) Install the air intake chamber. IN(H6DO)-6, INSTALLATION, Air Intake Cham-
ber.>
C: INSPECTION
Make sure the hose is not cracked or clogged.
AT-03252
AT-03252

5AT-61
Oil Charge Pipe
AUTOMATIC TRANSMISSION
22.Oil Charge Pipe
A: REMOVAL
1) Remove the air intake chamber. IN(H6DO)-6, REMOVAL, Air Intake Chamber.>
2) Remove the oil charge pipe, and then remove
the O-ring from flange side.
B: INSTALLATION
1) Install the oil charge pipe with a new O-ring.
Tightening torque:
41 N·m (4.2 kgf-m, 30.4 ft-lb)
2) Install the air intake chamber. IN(H6DO)-6, INSTALLATION, Air Intake Cham-
ber.>
C: INSPECTION
Make sure the oil charge pipe is not deformed or
damaged.
(A) Oil level gauge
(B) Oil charge pipe
(A) Oil level gauge
(B) Oil charge pipe
AT-01386
(B)
(A)
AT-01386
(B)
(A)