2009 RENAULT TWINGO Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-81
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: WIPING POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Rear screen
wiperAC007:Rear screen wiperThis command is used to
operate the rear screen
wiper.In the event of a fault, apply the
procedure for dealing with
command AC007.
Wiper speedAC058:Intermittent wiper
operationThis command is used to
operate the intermittent
windscreen wiper action.In the event of a fault, apply the
procedure for dealing with
command AC058.
AC056:Low-speed wiperThis command is used to
operate the windscreen
wipers at low speed.In the event of a fault, apply the
procedure for dealing with
command AC056.
AC057:High-speed wiperThis command is used to
operate the windscreen
wipers at high speed.In the event of a fault, apply the
procedure for dealing with
command AC057.

87B-82
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: BATTERY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Battery voltagePR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault
finding on the charging circuit
(see 80A, Battery).
PR074:Battery setpoint
voltageIndicates the battery
setpoint in V.In the event of a fault, apply the
interpretation of parameter
PR074.
PR076:Battery voltage after
restIndicates the battery
voltage after rest in V.In the event of a fault, apply the
interpretation of parameter
PR076.
Alternator
operationET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, apply the
interpretation of status ET142.

87B-83
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ALTERNATOR
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Battery voltagePR073:Alternator charge
signalIndicates the
alternator charge in V.In the event of a fault, apply the
interpretation of parameter PR073.
Alternator
setpointPR075:Alternator setpoint
voltage
Indicates the alternator
setpoint in V.In the event of a fault, apply the
interpretation of parameter PR075.
Battery voltagePR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault finding
on the charging circuit (see, 80A
Battery), run fault finding on the
multiplex network (see 88B,
Multiplex) and run fault finding on the
injection (see 13B, Diesel injection
or 17B, Petrol injection).
EnginePR024:Engine coolant
temperature˚C
PR025:Engine speedrpmIn the event of a fault, run fault finding
on the multiplex network (see 88B,
Multiplex) and run fault finding on the
injection (see 13B, Diesel injection
or 17B, Petrol injection).
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, apply the
interpretation of status ET142.
AlternatorAC130:Alternator regulationIndicates the
regulation of the
alternator in volts.In the event of a fault, run fault finding
on the charging circuit (see 80A,
Battery).

87B-84
MR-413-X44-87B000$528.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*CPE: Electric central door locking
*RF: radio frequencyTool status Diagnostic tool title
ET008Blank UCH
ET015Passenger compartment blower
ET027Windscreen wiper park position
ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET044CPE* button
ET045RF* signal. received
ET046Engine immobiliser
ET047Brake pedal position
ET061Open tailgate request
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
MR-413-X44-87B000$528.mif
UCH
Vdiag No.: 44

87B-85
MR-413-X44-87B000$528.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87B
*SR: Sunroof.
*RF: radio frequencyTool status Diagnostic tool title
ET084Right-hand indicator request
ET085Hazard warning lights button
ET087One-touch window/SR* authorisation
ET096Wiper intermittent speed ring position
ET097Rear screen wiper park position
ET109Reverse gear engaged
ET111Front fog lights request
ET114Wiping request via rain sensor
ET115Request to switch on lights by light sensor
ET142Engine operating phase
ET181Key allocated to the vehicle
ET185Key code received
ET186Short press on door closing button
ET189Long press on door opening button
ET193RF* signal from a key allocated to the vehicle
ET229Injection immobiliser code
ET239Ignition switch position
ET240Key frequency (in Hz)
ET250Injection
ET463Door(s) or tailgate

87B-86
MR-413-X44-87B000$576.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET008
BLANK UCH
NOTESNo faults should be present or stored.
SPECIFICATIONSYES
NO
ET008 is YES.
Program the UCH using SC004 Program UCH.
Apply the procedure after replacing the computer (see Replacement of components).
ET008 is NO.
If the UCH is not blank and has just been replaced, check whether the key is allocated (use command SC018 Key
check).
If the key is not allocated, allocate the keys using command SC015 Key allocation.
If the key is allocated, the UCH is operational.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET008
MR-413-X44-87B000$576.mif
UCH
Vdiag No.: 44

87B-87
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET015
PASSENGER COMPARTMENT FAN
NOTESNo faults should be present or stored.
Apply this status for vehicles fitted with manual air conditioning or heating.
Apply the checks if there is an inconsistency between the value of the status
and the air actually blown.
SPECIFICATIONSRUNNING
STOPPED
Check the configuration of the heating and air conditioning type of the vehicle:
–Check that LC013 "Air conditioning type" is "Heating" or "Manual" or "Automatic" according to the
equipment level. Otherwise carry out CF019 Air conditioning type.
Check the presence and condition of fuses F28 (30 A), F29 (15 A), F42 (10 A) on the passenger compartment
fuse and relay box (component code 1016).
Replace the fuse(s) if necessary.
Check the condition and connection of the connectors for the air conditioning control panel and blower unit
(manual air conditioning) (tabs bent, oxidised, broken).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET015

87B-88
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET015
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
Manual air conditioning between the air conditioning control panel (component code 319) and the blower unit:
Connection code 38AH between components 319 and 164.
Connection code 38AJ between components 319 and 164.
Connection code 38AK between components 319 and 164.
Connection code 38AL between components 319 and 164.
Connection code 38DA between components 164 and 1156.
Connection code 38DB between components 164 and 1156.
Connection code SP3 between components 164 and 1016.
Between the air conditioning control panel (component code 319) and the UCH: Climate control:
Connection code 38LQ between components 319 and 645.
Connection code 15M between components 319 and 645.
Connection code 15A between components 319 and 645.
Connection code 38LQ between components 319 and 645.
Connection code 38ES between components 319 and 645.
Connection code SP2 between component 319 and earth.
Connection code LPD between component 319 and earth.
Connection code SP3 between components 164 and 1016.
Connection code SP3 between components 164 and 1428.
Connection code NAM between component 319 and earth.
Connection code MAN between component 319 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.