2009 RENAULT TWINGO Chasiss Workshop Manual

37A-62
MECHANICAL COMPONENT CONTROLS
Clutch master cylinder: Removal - Refitting
JH3
37A
aUndo and remove the hydraulic clutch master cylin-
der (4) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the hydraulic clutch master cylinder onto the bulk-
head.
aFit the hydraulic clutch master cylinder.
aRemove the blanking plugs.
aFit the end of the hydraulic clutch control pipe onto
the hydraulic clutch master cylinder.
aPush in the metal clip.
aRemove the blanking plugs.
aConnect the brake fluid supply pipe to the hydraulic
clutch master cylinder.
aClip the hydraulic clutch master cylinder rod onto the
clutch pedal.
II - FINAL OPERATION.
aTop up the brake fluid reservoir.
aBleed the hydraulic clutch control pipe (see 37A,
Mechanical component controls, Clutch circuit:
Bleed, page 37A-54) .aRefit:
-the front wheel arch liner on the driver's side (see
Front wheel arch liner: Removal - Refitting) (MR
412, 55A, Exterior protection),
-the front wheel on the driver's side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
121342

37A-63
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Removal - Refitting
JH3
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front wheel on the driver's side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the front wheel arch liner on the driver's side (see
Front wheel arch liner: Removal - Refitting) (MR
412, 55A, Exterior protection),
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery),
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery).
aEmpty the brake fluid reservoir with a syringe.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aPress and hold the clip (1) .
aPull out the hydraulic clutch control pipe by one
notch.aPress and hold the clip (1) again.
aPull the hydraulic clutch control pipe out another
notch and collect the fluid in a container.
aDepress the clutch pedal to empty the hydraulic
clutch control circuit.
aDetach the pipe at (2) and (3) .
121354
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
121118
121114

37A-64
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Removal - Refitting
JH3
37A
aPull the clip (4) .
aUnclip the end piece (5) .
aRemove the hydraulic clutch control pipe.
aFit anti-contamination caps.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRemove the blanking plugs.
aRefit the clutch control pipe.
aFit the clutch control clip.
aConnect the pipe to the master cylinder and slave
cylinder.
II - FINAL OPERATION.
aBleed the clutch circuit (see 37A, Mechanical com-
ponent controls, Clutch circuit: Bleed, page 37A-
54) .
aTop up the brake fluid reservoir.
aCheck that the clutch system is operating correctly.
aRefit:
-the battery tray (see Battery tray: Removal - Re-
fitting) (MR 411, 80A, Battery),
-the battery (see Battery: Removal - Refitting)
(MR 411, 80A, Battery),-the front wheel arch liner on the driver's side (see
Front wheel arch liner: Removal - Refitting) (MR
412, 55A, Exterior protection),
-the front wheel on the driver's side (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
121341

37A-65
MECHANICAL COMPONENT CONTROLS
Manual gear control: List and location of components
JB1
37A
Gear control
121115
(1) « lever - mounting » assembly
(2) control bar

37A-66
MECHANICAL COMPONENT CONTROLS
Manual gear control: List and location of components
JH3
37A
Gear control
The control is only supplied as a « cable - lever -
mounting » assembly.
121116
(1) gear selection cable
(2) control cable
(3) « lever - mounting » assembly

37A-67
MECHANICAL COMPONENT CONTROLS
Gear control unit: Removal - Refitting
JH3 or JR5
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the centre console (see Centre console:
Removal - Refitting) (57A, Interior equipment).
aRemove:
-the clips (1) ,
-the heat shields (2) and (3) .
aRelease the exhaust pipe clamp.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the control cable (4) and selection cable (5)
from the ball joints in the direction of the arrows, us-
ing the open-jawed spanner as a lever.
aDetach the cable sleeve stops by pressing on the
tabs (6) and (7) . Tightening torquesm
gear control unit nuts12 Nm
exhaust clip21 Nm
121425
121357
121363
(4) control cable
(5) gear selection cable

37A-68
MECHANICAL COMPONENT CONTROLS
Gear control unit: Removal - Refitting
JH3 or JR5
37A
aRemove:
-the nuts (8) ,
-the gear control unit (9) by passing it between the
exhaust system and the tunnel.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the gear control unit by passing it between the
exhaust pipe and the tunnel
aTorque tighten the gear control unit nuts (12 Nm).
aAttach the sleeve stops of the control cable and gear
selection cable by clipping them to the gearbox.
aAttach the cables to the ball joints.
II - FINAL OPERATION.
aTorque tighten the exhaust clip (21 Nm).
aRefit:
-the heat shields,
-the central console (see Centre console: Remov-
al - Refitting) (57A, Interior equipment).
Note:
It is not necessary to adjust the control cable and
gear selection cable.

37A-69
MECHANICAL COMPONENT CONTROLS
Gear control unit: Removal - Refitting
JB1
37A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the catalytic converter (see Catalytic converter:
Removal - Refitting) (MR 411, 19B, Exhaust).
aRemove:
-the clips (1) and (2) ,
-the rear heat shield (3) .
aSlide the heat shield towards the front of the vehicle
(4) . Tightening torquesm
gear control unit nuts12 Nm
gear control linkage bolt28 Nm
121327
121328