2009 RENAULT SCENIC engine

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 183V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET042
CONTINUED 2
SPEED LIMITERWhen the driver presses the main switch in the speed limiter position, status ET042
becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in the
speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V after ignition feed on the main switch connector.
●Connection code AP43 of component 1081 (Mégane II).
●Connection code AP43 of component 1546 (Scénic II).
Disconnect the main switch and with it in the rest position, check the insulation between:
●Connection code AP43 and 3FX, of component 1081 (Mégane II).
●Connection code AP43 and 3PD, of component 1081 (Mégane II).
●Connection code AP43 and 3FX, of component 1546 (Scénic II).
●Connection code AP43 and 3PD, of component 1546 (Scénic II).
–Check the continuity between connections AP43 and 3PD of component 1081
(Mégane II) and component 1546 (Scénic II) in speed limiter position.
–Check the continuity between connections AP43 and 3FX of component 1081
(Mégane II) and component 1546 (Scénic II) in cruise control position.
If these checks show incorrect values, replace the main switch.
Check the insulation, continuity and the absence of interference resistance on the
following connections:
●Connection code 3FX,
●Connection code 3PD,
between components 1081 and 120 (Mégane II).
between components 1546 and 120 (Scénic II).
Also check the engine management computer connectors.
If there is a repair method (See Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 184V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET042
CONTINUED 3
CRUISE CONTROLWhen the driver presses the main switch in the cruise control position, status ET042
becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears although the driver pressed the switch in the
cruise control position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V after ignition feed on the main switch connector.
●Connection code AP43 of component 1081 (Mégane II).
●Connection code AP43 of component 1546 (Scénic II).
Disconnect the switch and when it is in the rest position, check the insulation between:
●Connection code AP43 and 3FX, of component 1081 (Mégane II).
●Connection code AP43 and 3PD, of component 1081 (Mégane II).
●Connection code AP43 and 3FX, of component 1546 (Scénic II).
●Connection code AP43 and 3PD, of component 1546 (Scénic II).
–Check the continuity between connections AP43 and 3PD of component 1081
(Mégane II) or component 1546 (Scénic II) in speed limiter position.
–Check the continuity between connections AP43 and 3FX of component 1081
(Mégane II) or component 1546 (Scénic II) in cruise control position.
If these checks show incorrect values, replace the main switch.
Check the insulation, continuity and the absence of interference resistance on the
following connections:
●Connection code 3FX,
●connection code 3PD.
Between components 1081 and 120 (Mégane II).
Between components 1546 and 120 (Scénic II).
Also check the engine management computer connectors.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 185V3 MR-372-J84-13B250$630.mif
PROHIBITED
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET076
STARTING
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
AUTHORISED
Starting the vehicle is authorised when the UCH authorises starting.
Status ET076 changes to AUTHORISED if the vehicle cards are recognised and the
engine immobiliser is inactive.
If the card is not recognised by the UCH, starting the vehicle is prohibited.
Status ET076 is PROHIBITED and the vehicle cannot be started.
Run fault finding on the UCH (see 87B, Passenger compartment connection unit).
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET076

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 186V3 MR-372-J84-13B250$630.mif
NO
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET077
IMPACT DETECTED
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
YES
If the vehicle has been involved in an accident, the injection computer receives the
impact signal via the multiplex network and may switch off the ignition. Status ET077 is
YES.
Switch off the ignition for 1 minute then switch on the ignition again so the engine can be
started.
Carry out a multiplex network test and deal with any faults.
Under normal operating conditions, status ET077 is NO when the computer has received
no impact signal.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET077

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 187V3 MR-372-J84-13B250$630.mif
INACTIVE
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET088
REQUEST TO START COMPRESSOR
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
ACTIVE
Status ET088 becomes ACTIVE if there has been a request for air conditioning (press
the AC or AUTO button, with maximum cold) and if status ET004 is YES.
The selection is made on the air conditioning control panel, the request for air
conditioning is transmitted to the UCH which in turn transmits the request to the injection
computer which either authorises or does not authorise the compressor to switch on. If
the injection computer authorises the compressor to switch on, its sends the
compressor on request to the UPC and status ET088 COMPRESSOR ON REQUEST
becomes ACTIVE (Climate control).
If the vehicle is equipped with manual air conditioning, the air conditioning request is
transmitted from the air conditioning control panel to the UCH which then accepts or does
not accept the air conditioning compressor coming on depending on the operating status
of the passenger compartment fan. When the request has been accepted, the request
to switch on the compressor is transmitted to the injection computer which either
authorises or does not authorise the compressor to start.
If the injection computer authorises the compressor to switch on, its sends the
compressor on request to the UPC and status ET088 COMPRESSOR ON REQUEST
becomes ACTIVE.
If there has been no compressor on request and status ET088 remains ACTIVE
(see 62A, Air conditioning).
Note:
Switching on the compressor is only authorised when the engine is running.
Switching on the compressor is ultimately controlled the UPC.
Status ET088 is INACTIVE when there has been no air conditioning request and
when the compressor has not been authorised to come on (ET004 is NO or when
the driver turns off the air conditioning).
If there has been no compressor on request and status ET088 remains INACTIVE (see
62A, Air conditioning).
Note:
Switching on the compressor is only authorised when the engine is running.
Switching on the compressor is ultimately controlled the UPC.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET088

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 188V3 MR-372-J84-13B250$630.mif
DEFECTIVE
NO
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET104
INJECTOR CODE USE
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
YES
Status ET104 is YES if the IMA option (individual injector correction) is activated in
the injection computer.
All the injectors have IMA codes etched on the bakelite body, but not all computers
use them.
In the case of a computer configured with the IMA option, the injector codes must be
entered into the injection computer in the following scenarios:
–when one or more injectors is replaced,
–when the injection computer is replaced,
–when the injection computer is reprogrammed.
If the injector codes are not programmed after these operations, fault DF276
Injector code programming will be present, and the engine will operate in defect
mode.
In this case, run command SC002 Enter injector codes, applying the procedure
described in the interpretation of this command.
Status ET104 is NO if the computer is not configured to interpret the IMA codes
(individual injector correction).
In this case, run command SC002 Enter injector codes, applying the procedure
described in the interpretation of this command.
Status ET104 is FAULTY if the computer does not have IMA codes in the memory.
Fault DF276 Injector code programming is present and the engine runs in defect
mode.
Run command SC002 Enter injector codes applying the procedure described in the
interpretation of this command.
If at the end of the procedure status ET104 remains FAULTY, contact Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET104

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 191V3 MR-372-J84-13B250$630.mif
COMPLETED
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET238
SYNCHRONISATION
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
WARNING
Synchronisation is carried out during the engine starting phase. This is established between the camshaft position
sensor and the TDC sensor.
Once this synchronisation has been carried out, it enables the computer to identify cylinder no. 1 and to calculate
the precise position of the cylinder's Top Dead Centre.
NOT PERFORMED
When the engine is stopped but the ignition switched on, cylinder no. 1 is no longer
indicated.
Status ET238 is NOT DONE; synchronisation between the crankshaft and the camshaft
has not been carried out.
Synchronisation is carried out during the engine starting phase.
Cylinder No. 1 is indicated and synchronisation will be performed once the engine is
started.
Status ET238 is DONE.
If after several attempts to start the engine, status ET238 remains NOT DONE, refer to
the interpretation of the following faults:
–DF005 Engine speed sensor circuit.
–DF097 Camshaft sensor circuit.
If the engine does still not start, consult the Customer complaints section, ALP2
Starting faults.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic tool
EDC16_V51_ET238

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 192V3 MR-372-J84-13B250$630.mif
NO
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET341
IMMOBILISER CODE PROGRAMMED
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
YES
Status ET341 becomes YES if dialogue is established between the UCH and the
injection computer and the card code is recognised.
The engine is only authorised to start if the code is recognised by the UCH computer and
status ET003 Engine immobiliser is INACTIVE.
The code remains NO if dialogue between the UCH and the injection computer is not
possible. Status ET003 Engine immobiliser is ACTIVE.
The cause of the malfunction may be due to the incorrect programming of the cards,
(see 97B, Passenger compartment connection unit, configuration and
programming); follow the card programming procedure.
If the malfunction is not due to the card codes, test the multiplex network (when fault
finding is carried out for functions) and check that there is dialogue between the UCH,
the Protection and Switching Unit and the injection computer.
If dialogue is not established, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
EDC16_V51_ET341