DIESEL INJECTION
Fault finding – Test13B
13B -266V3 MR-372-J84-13B250$900.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
TEST10 Diesel fuel conformity check
WARNING
During t hisop eration, it is essential t o:
–refrain from smoking or bringing incandescent objects close to the work area,
–protect yourself against fuel splashes due to residual pressure in the pipes,
–wear safety goggles with side guards,
–wear leaktight gloves (Nitrile type).
IMPORTA NT
–To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
–To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Preparations:
Weigh an empty 1300 ml plastic cup (part no. 77 11 171 413) with its cover (part no. 77 11 171 416) using
electronic scales such as those used in body paint workshops (example: PANDA part no. 77 11 224 995). Record
the weight of the empty plastic cup.
This type of plastic cup is used to prepare paint.
Remove 1 litre of fuel at the diesel filter outlet (see MR 364 (Mégane II) or MR 370 (Scénic II), Mechanical,
19C, Tank, Draining the fuel tank), using a pneumatic transfer pump (part no. 634-200) and place it in the
1300 ml plastic cup.
Cover the plastic cup with its cover and let it settle for approximately 2 minutes.
Is the fuel cloudy or does it
separate into two parts?YESThe diesel fuel contains water and is not compliant.
Drain the fuel circuit, including the tank (see MR 364
(Mégane II) or MR 370 (Scénic II), Mechanical, 19C,
Tank, Draining the fuel tank).
NO
EDC16_V51_TEST10
DIESEL INJECTION
Fault finding – Test13B
13B -267V3 MR-372-J84-13B250$900.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
TEST10
CONTINUED 1
Weigh the diesel fuel and note the fuel weight after subtracting the weight of the empty plastic cup and its cover.
Does the fuel weight fall between the minimum and maximum weights given in the table below?
Calculated weight (g.) Fuel
temperature
(˚C) Min. weight Max. weight
821 846 13
821 846 14
820 845 15
819 844 16
819 844 17
818 843 18
817 842 19
816 841 20
816 841 21
815 840 22
814 839 23
814 839 24
813 838 25
Check the fuel temperature by immersing a thermometer in the plastic cup.
YES NO
End of test. The fuel is not correct.
If the fuel weight is l ess than the minimum value then there is petrol in the diesel fuel.
If the fuel weight is greater than the maximum value then there is oil in the diesel fuel.
Drain the fuel circuit, including the tank (seeMR 364 (Mégane II)orMR 370 (Scénic
II), Mechanical, 19C, Tank, Draining the fuel tank).
DIESEL INJECTION
Fault finding – Test13B
13B -268V3 MR-372-J84-13B250$900.mif
TEST10
CONTINUED 2
Note:
If the weight measured reaches the limit values, the measurement can be performed with a 2230 ml plastic cup
(part no.77 11 171 414) and its cover (part no.77 11 171 417):
–Carry out a quick test drive in order to mix the fuel, then remove 2 l of fuel.
–Perform the test again and check the results by multiplying the limit values by 2.
Contact the Techline if you have doubts or problems with the customer.
EDC16
PROGRAM No.: C1
Vdiag No.: 51
