2009 HUMMER H3 light

8. Proceed to the driver side rear
tire, and repeat the procedure
in Step 5.
9. After hearing the conrming horn
chirp for the driver side rear tire,
check to see if the TPMS low tire
warning light and the DIC LOW
TIRE messages have turned off.
If yes, the TPMS sensors have
been relearned. Turn the ignition
switch to LOCK/OFF.
If the low tire warning light and
the SERV TPM message on the
DIC are on after completing
Step 5 for the driver side rear tire,
the sensor relearn process has
not been successful. Turn the
ignition switch to LOCK/OFF and
repeat the matching process
beginning with Step 2.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire,
for signs of wear or damage.
SeeWhen It Is Time for
New Tires on page 5-58for
more information.
Tires should be rotated
every 5,000 to 8,000 miles
(8 000 to 13 000 km).
SeeScheduled Maintenance
on page 6-4.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the
vehicle continues to perform
most like it did when the
tires were new.Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
SeeWhen It Is Time for
New Tires on page 5-58and
Wheel Replacement on
page 5-64.
Make sure the spare tire is
stored securely. Push, pull and
then try to rotate or turn the
tire. If it moves, use the wheel
wrench/hoist shaft to tighten
the cable. SeeChanging a
Flat Tire on page 5-66.
Service and Appearance Care 5-57

Uniform Tire Quality
Grading
Quality grades can be found
where applicable on the
tire sidewall between tread
shoulder and maximum section
width. For example:
Treadwear 200 Traction AA
Temperature A
The following information relates
to the system developed by
the United States National
Highway Traffic Safety
Administration (NHTSA), which
grades tires by treadwear,
traction, and temperature
performance. This applies
only to vehicles sold in the
United States. The grades are
molded on the sidewalls of
most passenger car tires.The Uniform Tire Quality
Grading (UTQG) system
does not apply to deep tread,
winter-type snow tires,
space-saver, or temporary use
spare tires, tires with nominal rim
diameters of 10 to 12 inches
(25 to 30 cm), or to some
limited-production tires.
While the tires available on
General Motors passenger cars
and light trucks may vary
with respect to these grades,
they must also conform to
federal safety requirements and
additional General Motors
Tire Performance Criteria (TPC)
standards.
Treadwear
The treadwear grade is a
comparative rating based on
the wear rate of the tire
when tested under controlled
conditions on a specied
government test course.For example, a tire graded
150 would wear one and a half
(1.5) times as well on the
government course as a tire
graded 100. The relative
performance of tires depends
upon the actual conditions
of their use, however, and may
depart signicantly from the
norm due to variations in
driving habits, service practices,
and differences in road
characteristics and climate.
Traction – AA, A, B, C
The traction grades, from highest
to lowest, are AA, A, B, and C.
Those grades represent the
tire’s ability to stop on wet
pavement as measured under
controlled conditions on
specied government test
surfaces of asphalt and
concrete. A tire marked C may
have poor traction performance.
5-62 Service and Appearance Care

4. Use the wheel wrench to tighten
the nuts rmly. Try to move the
tire back and forth slightly to
be sure it is secure.
5. Reinstall the center tire cover
onto the spare or at tire.
6. If the vehicle has a spare tire
cover close the cover and
latch the side latch.To store the jack tool bag and jack:
1. Return the tools to the jack
tool bag.
2. Secure the tool bag to the jack
by securely wrapping the straps
around the jack. Then, slide
the straps through the rings on
the bag and secure.
3. Position the jack and jack tool
bag in the swing-gate.
When reinstalling the jack and
jack tool bag, make sure the jack
base is securely seated behind
the tabs in the swing-gate.4. Reinstall the wing nut retainer to
fasten the jack and tool bag in
the storage compartment.
Make sure that the wing nut
passes through the tool bag and
the jack before tightening it.
5. Turn the wing nut retainer
clockwise to secure.
6. Reinstall the compartment cover
by inserting the locator tabs in
the holes in the swing-gate.
Push the latches down to secure.
Service and Appearance Care 5-79

To store the jack tool bag and jack:
1. Return the tools to the jack
tool bag.
2. Secure the tool bag to the jack
by securely wrapping the straps
around the jack. Then, slide
the straps through the rings on
the bag and secure.
3. Reinstall the wing nut retainer to
fasten the jack and tool bag
under the rear seat.
Make sure that the wing nut
passes through the tool bag and
the jack before tightening it.
4. Turn the wing nut retainer
clockwise to secure.Spare Tire
The vehicle, when new, had a
fully-inated spare tire. A spare tire
may lose air over time, so check
its ination pressure regularly.
SeeInflation - Tire Pressure on
page 5-51andLoading the Vehicle
on page 4-35for information
regarding proper tire ination and
loading your vehicle. For instruction
on how to remove, install or store
a spare tire, seeRemoving the Flat
Tire and Installing the Spare Tire
on page 5-72andStoring a Flat or
Spare Tire and Tools (H3) on
page 5-78orStoring a Flat or Spare
Tire and Tools (H3T) on page 5-80.
After installing the spare tire on
your vehicle, you should stop
as soon as possible and make sure
the spare is correctly inated.The spare tire does not have a Tire
Pressure Monitor System sensor.
You may get a low pressure warning
light. SeeTire Pressure Monitor
Operation on page 5-54. Have the
damaged or at road tire repaired or
replaced as soon as you can.
Do not mix tires and wheels of
different sizes, because they will not
t. Keep your spare tire and its
wheel together.
5-82 Service and Appearance Care

Appearance Care
Interior Cleaning
The vehicle’s interior will continue to
look its best if it is cleaned often.
Although not always visible,
dust and dirt can accumulate on the
upholstery. Dirt can damage
carpet, fabric, leather, and plastic
surfaces. Regular vacuuming
is recommended to remove particles
from the upholstery. It is important
to keep the upholstery from
becoming and remaining heavily
soiled. Soils should be removed as
quickly as possible. The vehicle’s
interior may experience extremes of
heat that could cause stains to
set rapidly.
Lighter colored interiors may require
more frequent cleaning. Use care
because newspapers and garments
that transfer color to home
furnishings may also transfer color
to the vehicle’s interior.When cleaning the vehicle’s interior,
only use cleaners specically
designed for the surfaces being
cleaned. Permanent damage may
result from using cleaners on
surfaces for which they were not
intended. Use glass cleaner only on
glass. Remove any accidental
over-spray from other surfaces
immediately. To prevent over-spray,
apply cleaner directly to the
cleaning cloth.
Notice:Using abrasive cleaners
when cleaning glass surfaces
on the vehicle, could scratch the
glass and/or cause damage to
the rear window defogger.
When cleaning the glass on the
vehicle, use only a soft cloth
and glass cleaner.
Many cleaners contain solvents that
may become concentrated in the
vehicle’s breathing space. Before
using cleaners, read and adhere
to all safety instructions on the label.
While cleaning the vehicle’sinterior, maintain adequate
ventilation by opening the vehicle’s
doors and windows.
Dust may be removed from small
buttons and knobs using a small
brush with soft bristles.
Products that remove odors from
the vehicle’s upholstery and
clean the vehicle’s glass can be
obtained from your dealer/retailer.
Do not clean the vehicle using:
A knife or any other sharp object
to remove a soil from any interior
surface.
A stiff brush. It can cause
damage to the vehicle’s interior
surfaces.
Heavy pressure or aggressive
rubbing with a cleaning cloth.
Use of heavy pressure can
damage the interior and does
not improve the effectiveness of
soil removal.
Service and Appearance Care 5-83

Weatherstrips
Silicone grease on weatherstrips will
make them last longer, seal better,
and not stick or squeak. Apply
silicone grease with a clean cloth.
During very cold, damp weather
frequent application may be
required. SeeRecommended Fluids
and Lubricants on page 6-12.
Washing Your Vehicle
The best way to preserve the
vehicle’s nish is to keep it clean by
washing it often.
Notice:Certain cleaners contain
chemicals that can damage the
emblems or nameplates on the
vehicle. Check the cleaning
product label. If it states that it
should not be used on plastic
parts, do not use it on the vehicle
or damage may occur and it would
not be covered by the warranty.
Do not wash the vehicle in direct
sunlight. Use a car washing soap.
Do not use cleaning agents that arepetroleum based or that contain
acid or abrasives, as they can
damage the paint, metal or plastic
on the vehicle. Approved cleaning
products can be obtained from
your dealer/retailer. Follow all
manufacturers’ directions regarding
correct product usage, necessary
safety precautions and appropriate
disposal of any vehicle care product.
Rinse the vehicle well, before
washing and after to remove all
cleaning agents completely. If they
are allowed to dry on the surface,
they could stain.
Dry the nish with a soft, clean
chamois or an all-cotton towel to
avoid surface scratches and
water spotting.
High pressure car washes may
cause water to enter the vehicle.
Avoid using high pressure washes
closer than 12 inches (30 cm) to
the surface of the vehicle. Use of
power washers exceeding 1,200 psi
(8 274 kPa) can result in damage
or removal of paint and decals.
Cleaning Exterior
Lamps/Lenses
Use only lukewarm or cold water,
a soft cloth and a car washing soap
to clean exterior lamps and lenses.
Follow instructions underWashing
Your Vehicle on page 5-86.
Finish Care
Occasional waxing or mild polishing
of the vehicle by hand may be
necessary to remove residue from
the paint nish. Approved cleaning
products can be obtained from
your dealer/retailer.
If the vehicle has a basecoat/
clearcoat paint nish, the clearcoat
gives more depth and gloss to
the colored basecoat. Always use
waxes and polishes that are
non-abrasive and made for a
basecoat/clearcoat paint nish.
5-86 Service and Appearance Care

Electrical System
Add-On Electrical
Equipment
Notice:Do not add anything
electrical to the vehicle unless you
check with your dealer/retailer
rst. Some electrical equipment
can damage the vehicle and the
damage would not be covered by
the vehicle’s warranty. Some
add-on electrical equipment can
keep other components from
working as they should.
Add-on equipment can drain the
vehicle’s battery, even if the vehicle
is not operating.
The vehicle has an airbag system.
Before attempting to add anything
electrical to the vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 1-58.
Windshield Wiper Fuses
The windshield wiper motor is
protected by a circuit breaker and a
fuse. If the motor overheats due
to heavy snow or ice, the wiper will
stop until the motor cools. If the
overload is caused by some
electrical problem, have it xed.
Power Windows and
Other Power Options
Circuit breakers protect the
power windows and other power
accessories. When the current load
is too heavy, the circuit breaker
opens and closes, protecting the
circuit until the problem is xed
or goes away.
Power and Heated Seat
Circuit Breakers
There is a circuit breaker located
underneath the driver’s side
front seat that controls the power
and heated seat functions.
Fuses and Circuit
Breakers
The wiring circuits in your vehicle
are protected from short circuits by a
combination of fuses and circuit
breakers. This greatly reduces the
chance of res caused by electrical
problems.
Look at the silver-colored band
inside the fuse. If the band is
broken or melted, replace the fuse.
Be sure you replace a bad fuse
with a new one of the identical size
and rating.
If you ever have a problem on the
road and do not have a spare
fuse, you can borrow one that has
the same amperage. Just pick some
feature of your vehicle that you
can get along without — like the
radio or cigarette lighter — and use
its fuse, if it is the correct amperage.
Replace it as soon as you can.
Service and Appearance Care 5-91

Fuse Usage
11 Not Used
12Transfer Case Control
Module
13 Radio
14 Body Control Module
15Rear Wiper Motor
(H3 Only)
16Rear Wiper Pump
Switch (H3 Only)
17Air Injection Reactor
(AIR) Pump Relay/
Transmission Control
Module (TCM)
(V8 Only)
18 Rear Vision Camera
19 Cluster
20Rear Turn Lamp,
Hazard Lamp
21Powertrain Control
Module 1
22Mass Air Flow Sensor,
Canister Vent Purge
SolenoidFuse Usage
23 Injector/V8 Coil
24 Fog Lamp
25Powertrain Control
Module B
26Transmission Control
Module (TCM)
27 Airbags
28 Not Used
29Antilock Brakes,
StabiliTrak
®
30 Rear Window Defogger
31 Canister Vent
32Regulated Voltage
Control Sensor
33 Ignition 1 (V8 Only)
34 Transmission
35Cruise Control,
Miscellaneous
36 Horn
37Driver Side Rear
Park Lamp
Fuse Usage
38 Amplier
39Daytime Running
Lamps
40Passenger Side
Headlamp
41 Driver Side Headlamp
42 Trailer Back-Up Lamp
43 Front Park Lamps
44Air Injection Reactor
(AIR) Solenoid
45Auxiliary Power 2/
Cigarette Lighter
46Electronic Throttle
Control
47 Oxygen Sensor
48 Air Conditioning Clutch
49 Rear Park Lamp
50 Stop Lamp
51Auxiliary Power 1/
Cigarette Lighter
52StabiliTrak
®, Antilock
Brakes
5-94 Service and Appearance Care