2009 HUMMER H3 spare tire location

CAUTION (Continued)
So if you do not use proper care
before backing up, you could
hit a vehicle, child, pedestrian,
bicyclist, or pet, resulting in
vehicle damage, injury, or death.
Even though the vehicle has the
RVC system, always check
carefully before backing up by
checking behind and around
the vehicle.Rear Vision Camera Location
The image on the screen is provided
by the camera located on the rear
bumper.The image from the camera that
appears on the screen appears
farther than the actual distance.
The area displayed by the camera
is limited. The camera does not
display objects which are close to
either corner of the bumper or under
the bumper. On the H3, the spare
tire and carrier extends rearward
of the rear bumper. The area
displayed on the screen may vary
according to vehicle orientation
or road conditions. View of H3 Camera Location
View of H3T Camera Location
Features and Controls 2-37

Front Axle
It is not necessary to regularly
check front axle uid unless a leak
is suspected or an unusual noise
is heard. A uid loss could indicate
a problem.
It is recommended that the front
axle uid be checked and lled by
your dealer/retailer.
Headlamp Aiming
The vehicle may have a visual
optical headlamp aiming system.
The aim has been preset at
the factory and should need no
further adjustment.
However, if the vehicle is damaged
in a crash, the headlamp aim
may be affected and adjustment
may be necessary.
If oncoming vehicles ash their
high beams at you, this may also
mean the vertical aim needs to
be adjusted.
It is recommended that the vehicle
is taken to your dealer/retailer
for service if the headlamps need to
be re-aimed. It is possible however,
to re-aim the headlamps as
described.The vehicle should be:Placed so the headlamps are
25 ft. (7.6 m) from a light
colored wall or other at surface.
On a level surface which is level
all the way to a wall.
Placed so it is at a right angle to
the wall or other at surface.
Clear of any snow, ice, or
mudonit.
Fully assembled, the tires
properly inated, and all other
work stopped while headlamp
aiming is being performed.
Normally loaded with the spare
tire in its original location and a
full tank of fuel and one person or
160 lbs (75 kg) sitting on the
driver seat.
Service and Appearance Care 5-39

Tire Pressure Monitor
Operation
This vehicle may have a Tire
Pressure Monitor System (TPMS).
The TPMS is designed to warn
the driver when a low tire pressure
condition exists. TPMS sensors
are mounted onto each tire and
wheel assembly on the vehicle,
excluding the spare tire. The TPMS
sensors monitor the air pressure
in the vehicle’s tires and transmit the
tire pressure readings to a receiver
located in the vehicle.
When a low tire pressure condition
is detected, the TPMS illuminates
the low tire pressure warning light
located on the instrument panel
cluster.At the same time, a Driver
Information Center (DIC) message
is displayed on the DIC display
screen. The low tire pressure
warning light and the DIC warning
message come on at each
ignition cycle until the tires are
inated to the correct ination
pressure. For additional information
and details about the DIC operation
and displays seeDIC Operation and
Displays on page 3-34andDIC
Warnings and Messages on
page 3-37.
The low tire pressure warning light
may come on in cool weather
when the vehicle is rst started, and
then turn off as you start to drive.
This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.A Tire and Loading Information
label, attached to the vehicle, shows
the size of the vehicle’s original
equipment tires and the correct
ination pressure for the vehicle’s
tires when they are cold. See
Loading the Vehicle on page 4-35,
for an example of the Tire and
Loading Information label and its
location on the vehicle. Also see
Inflation - Tire Pressure on
page 5-51.
The vehicle’s TPMS can warn you
about a low tire pressure condition
but it does not replace normal
tire maintenance. SeeTire
Inspection and Rotation on
page 5-57andTires on page 5-44.
Notice:Liquid tire sealants
could damage the Tire Pressure
Monitor System (TPMS) sensors.
Sensor damage caused by using
a tire sealant is not covered
by your warranty. Do not use
liquid tire sealants.
5-54 Service and Appearance Care

You need new tires if any of the
following statements are true:
You can see the indicators at
three or more places around
the tire.
You can see cord or fabric
showing through the tire’s rubber.
The tread or sidewall is cracked,
cut, or snagged deep enough to
show cord or fabric.
The tire has a bump, bulge,
or split.
The tire has a puncture, cut, or
other damage that cannot be
repaired well because of the size
or location of the damage.The rubber in tires degrades over
time, even if they are not being
used. This is also true for the spare
tire, if the vehicle has one. Multiple
conditions affect how fast this
aging takes place, including
temperatures, loading conditions,
and ination pressure maintenance.
With proper care and maintenance
tires typically wear out before
they degrade due to age. If you are
unsure about the need to replace
the tires as they get older, consult
the tire manufacturer for more
information.
Buying New Tires
GM has developed and matched
specic tires for your vehicle.
The original equipment tires
installed on your vehicle,
when it was new, were designed
to meet General Motors
Tire Performance Criteria
Specication (TPC spec) system
rating. If you need replacement
tires, GM strongly recommends
that you get tires with the
same TPC Spec rating. This
way, your vehicle will continue to
have tires that are designed to
give the same performance
and vehicle safety, during normal
use, as the original tires.
Service and Appearance Care 5-59

Removing the Flat Tire
and Installing the
Spare Tire
1. Do a safety check before
proceeding. SeeChanging a
Flat Tire on page 5-66for
more information.
2. Remove the center cap by
placing the at end of the wheel
wrench in the slot on the wheel
and gently pry the center cap out.3. Turn the wheel wrench
counterclockwise to loosen the
wheel nuts. Do not remove
them yet.
If the vehicle has locking lug
nuts, the key is supplied in the
tool bag. Use the key along
with the wheel wrench to remove
the wheel nuts from the tire.
Now jack up the vehicle.A. Front Position - Lower
Control Arm
B. Rear Position - Lower Axle
4. Locate the vehicle’s jacking
positions (A and B).
Jacking Locations (Overall View)
5-72 Service and Appearance Care

6. Turn the wheel wrench clockwise
to raise the jack head to the
lifting point.
{CAUTION
Getting under a vehicle when it is
jacked up is dangerous. If the
vehicle slips off the jack, you
could be badly injured or killed.
Never get under a vehicle when it
is supported only by a jack.
{CAUTION
Raising your vehicle with the jack
improperly positioned can damage
the vehicle and even make the
vehicle fall. To help avoid
personal injury and vehicle
damage, be sure to t the jack lift
head into the proper location
before raising the vehicle.7. Remove all the wheel nuts and
take off the at tire.
{CAUTION
Rust or dirt on a wheel, or on the
parts to which it is fastened, can
make wheel nuts become loose
after time. The wheel could come
off and cause an accident. When
changing a wheel, remove any
rust or dirt from places where the
wheel attaches to the vehicle.
In an emergency, use a cloth or a
paper towel to do this; but be sure
to use a scraper or wire brush
later, if needed, to get all the rust
or dirt off. SeeChanging a Flat
Tire on page 5-66.8. Remove any rust or dirt from the
wheel bolts, mounting surfaces
and spare wheel.{CAUTION
Never use oil or grease on bolts
or nuts because the nuts might
come loose. The vehicle’s wheel
could fall off, causing a crash.
9. Put the spare tire on the
mounting surface.
10. Put the wheel nuts back on
with the rounded end of the
nuts toward the wheel
after mounting the spare.
5-74 Service and Appearance Care