2009 HUMMER H3 light

Cellular Phone Usage
Cellular phone usage may cause
interference with the vehicle’s radio.
This interference may occur when
making or receiving phone calls,
charging the phone’s battery,
or simply having the phone on. This
interference causes an increased
level of static while listening to
the radio. If static is received while
listening to the radio, unplug the
cellular phone and turn it off.
Fixed Mast Antenna
The xed mast antenna can
withstand most car washes without
being damaged as long as it is
securely attached to the base. If the
mast becomes slightly bent,
straighten it out by hand. If the mast
is badly bent, replace it.
Occasionally check to make sure
the antenna is tightened to its base.
If tightening is required, tighten
by hand. until fully seated plus one
quarter turn.
XM™ Satellite Radio
Antenna System
The XM Satellite Radio antenna is
located on the roof of the vehicle.
Keep the antenna clear of
obstructions for clear radio
reception.
If the vehicle has a sunroof, the
performance of the XM system may
be affected if the sunroof is open.
Instrument Panel 3-63

Police records show that almost
40 percent of all motor
vehicle-related deaths involve
alcohol. In most cases, these
deaths are the result of someone
who was drinking and driving.
In recent years, more than
17,000 annual motor vehicle-related
deaths have been associated
with the use of alcohol, with about
250,000 people injured.
For persons under 21, it is
against the law in every U.S. state
to drink alcohol. There are good
medical, psychological, and
developmental reasons for
these laws.
The obvious way to eliminate the
leading highway safety problem
is for people never to drink alcohol
and then drive.
Medical research shows that
alcohol in a person’s system can
make crash injuries worse,
especially injuries to the brain,
spinal cord, or heart. This means
that when anyone who hasbeen drinking — driver or
passenger — is in a crash, that
person’s chance of being killed or
permanently disabled is higher than
if the person had not been
drinking.
Control of a Vehicle
The following three systems
help to control the vehicle while
driving — brakes, steering,
and accelerator. At times, as when
driving on snow or ice, it is easy
to ask more of those control systems
than the tires and road can
provide. Meaning, you can lose
control of the vehicle. SeeTraction
Control System (TCS) on page 4-7.
Adding non-dealer/non-retailer
accessories can affect vehicle
performance. SeeAccessories and
Modifications on page 5-3.
Braking
SeeBrake System Warning Light on
page 3-27.
Braking action involves perception
time and reaction time. Deciding
to push the brake pedal is
perception time. Actually doing
it is reaction time.
Average reaction time is about
three-fourths of a second. But that
is only an average. It might be
less with one driver and as long as
two or three seconds or more
with another. Age, physical
condition, alertness, coordination,
and eyesight all play a part. So
do alcohol, drugs, and frustration.
But even in three-fourths of a
second, a vehicle moving at 60 mph
(100 km/h) travels 66 feet (20 m).
That could be a lot of distance in an
emergency, so keeping enough
space between the vehicle
and others is important.
Driving Your Vehicle 4-3

And, of course, actual stopping
distances vary greatly with the
surface of the road, whether it is
pavement or gravel; the condition of
the road, whether it is wet, dry, or
icy; tire tread; the condition of
the brakes; the weight of the vehicle;
and the amount of brake force
applied.
Avoid needless heavy
braking. Some people drive in
spurts — heavy acceleration
followed by heavy braking — rather
than keeping pace with traffic.
This is a mistake. The brakes might
not have time to cool between
hard stops. The brakes will wear out
much faster with a lot of heavy
braking. Keeping pace with
the traffic and allowing realistic
following distances eliminates a lot
of unnecessary braking. That
means better braking and longer
brake life.
If the vehicle ever loses electrical
power while it is being driven, brake
normally but do not pump the
brakes. If the brakes are pumped,the pedal could get harder to push
down. If the vehicle loses electrical
power, there will still be some
power brake assist but it will be
used when the brake is applied.
Once the power assist is used up, it
can take longer to stop, the brake
pedal will be harder to push,
and you might experience longer
pedal travel.
Adding non-dealer/non-retailer
accessories can affect vehicle
performance. SeeAccessories and
Modifications on page 5-3.
Hill Start Assist
This vehicle has a Hill Start Assist
(HSA) feature, which may be
useful when the vehicle is stopped
on a grade. This feature is
designed to prevent the vehicle from
rolling, either forward or rearward,
during vehicle drive off. After
the vehicle is stopped on an incline,
push the brake pedal completely
to the oor to activate Hill StartAssist. When the system activates,
a chime will sound and the HSA
ON message will be displayed.
Letting off the brake pedal slightly or
applying the accelerator pedal to
disengage Hill Start Assist gives the
driver two seconds to pull forward
or back up before the vehicle
starts to roll. Lightly ease off the
brake pedal to disengage Hill
Start Assist. The brakes will
automatically be held for a maximum
of two seconds while the driver
switches from applying the brakes
to pushing the accelerator pedal.
When Hill Start Assist is active, the
driver might experience a “hard
pedal.” This is normal and does not
affect safe brake operation.
On steeper hills, Hill Start Assist will
only activate if the driver tries to
move the vehicle up the hill. It will
not activate if the vehicle is in a
drive gear and facing downhill or if
the vehicle is facing uphill and
in R (Reverse).
4-4 Driving Your Vehicle

Antilock Brake
System (ABS)
This vehicle has the Antilock Brake
System (ABS), an advanced
electronic braking system that will
help prevent a braking skid.
When the engine is started and the
vehicle begins to drive away,
ABS checks itself. A momentary
motor or clicking noise might
be heard while this test is going on.
This is normal.
If there is a problem with ABS, this
warning light stays on. See
Antilock Brake System (ABS)
Warning Light on page 3-28.Let us say the road is wet and you
are driving safely. Suddenly, an
animal jumps out in front of you. You
slam on the brakes and continue
braking. Here is what happens
with ABS:
A computer senses that the wheels
are slowing down. If one of the
wheels is about to stop rolling, the
computer will separately work
the brakes at each wheel.
ABS can change the brake pressure
to each wheel, as required, faster
than any driver could. This can help
the driver steer around the
obstacle while braking hard.
As the brakes are applied, the
computer keeps receiving updates
on wheel speed and controls braking
pressure accordingly.Remember: ABS does not change
the time needed to get a foot
up to the brake pedal or always
decrease stopping distance. If you
get too close to the vehicle in
front of you, there will not be enough
time to apply the brakes if that
vehicle suddenly slows or stops.
Always leave enough room up
ahead to stop, even with ABS.
Using ABS
Do not pump the brakes. Just hold
the brake pedal down rmly and
let antilock work. The brakes might
vibrate or some noise might be
heard, but this is normal.
Driving Your Vehicle 4-5

automatically disabled. See
Full-Time Four-Wheel Drive on
page 2-24for more information. It is
recommended to leave the system
on for normal driving conditions,
but it may be necessary to turn the
system off if the vehicle is stuck
in sand, mud, ice, or snow, and it is
necessary to “rock” the vehicle to
attempt to free it. SeeIf Your
Vehicle is Stuck in Sand, Mud, Ice,
or Snow on page 4-33.
To turn the system off, press and
hold the TCS/StabiliTrak button until
the traction off light comes on.
This light comes on steady when
TCS has been turned off. This light
ashes when StabiliTrak is active.To Turn off TCS and StabiliTrak,
press and hold the TCS/StabiliTrak
button until the STAB SYS OFF
message displays on the DIC. Press
and release the TCS/StabiliTrak
button again to turn StabiliTrak
back on. See “Traction Control
System (TCS)”, following, for more
information on turning TCS off
and on.
Traction Control
System (TCS)
The vehicle has a Traction Control
System (TCS) that limits wheel
spin. This is especially useful
in slippery road conditions. The
system operates only if it senses
that any of the wheels are spinning
or beginning to lose traction.
When this happens, TCS reduces
engine power. The system may
be heard or felt while it is working.
This is normal and does not
mean there is a problem with the
vehicle.TCS can operate on dry roads
under some conditions. When this
happens, the system may be
heard working or a reduction in
acceleration may be noticed. This is
normal and does not mean there
is a problem with the vehicle.
Examples of these conditions
include hard acceleration in a turn,
an abrupt upshift or downshift of
the transmission or driving on rough
roads.
If cruise control is being used when
TCS begins to limit wheel spin,
the cruise control automatically
disengages. The cruise control
can be re-engaged when road
conditions allow. SeeCruise Control
on page 3-9for more information.
TRACTION FAULT appears on
the Driver information Center (DIC)
when a TCS or antilock brake
system problem has been detected
and the vehicle needs service.
When this message is on, the
system will not limit wheel spin.
Driving Your Vehicle 4-7

Adjust your driving accordingly. See
DIC Warnings and Messages on
page 3-37for more information.
It is recommended to leave
the system on for normal driving
conditions, but it may be necessary
to turn the system off if the
vehicle is stuck in sand, mud, ice, or
snow, and it is necessary to
“rock” the vehicle to attempt to free
it. SeeIf Your Vehicle is Stuck
in Sand, Mud, Ice, or Snow
on page 4-33for more information.
To turn the system off, press and
release the TCS/StabiliTrak
®button.When TCS has been turned off, this
light comes on steady and TRAC
OFF appears on the DIC. This light
ashes when TCS is active.
Press and release the
TCS/StabiliTrak button again to turn
the system back on. The TRAC
OFF message then goes off. TCS
automatically comes on whenever
the vehicle is started and resets
itself at each ignition cycle.
Adding non-dealer/non-retailer
accessories can affect the vehicle’s
performance. SeeAccessories
and Modifications on page 5-3.
Locking Rear Axle
For vehicles with this feature,
additional traction can be obtained
from the rear wheels when
traveling in off-road situations such
as mud, snow, sand, steep hills
and uneven terrain.
The button used to turn this feature
on or off is located on the
instrument panel.
To lock the rear axle, do the
following:
1. Place the transfer case in the
4LO Lock mode. This is the
only mode which will allow
the rear axle to lock. See
Full-Time Four-Wheel Drive on
page 2-24for more information
regarding the transfer case
and 4LO Lock mode.
4-8 Driving Your Vehicle

2. Press the rear axle locking
button with the vehicle moving
less than 16 mph (26 km/h).
The light in the button stops ashing
and remains illuminated when the
rear axle is locked.
Notice:If you try to lock the axle
while the vehicle is stuck and
the tires are spinning, the
vehicle’s drivetrain could be
damaged. The repairs would not
be covered by the vehicle
warranty. Always lock the axle
before attempting situations
and/or navigating terrain which
could possibly cause the vehicle
to become stuck.
The locking rear axle will be
disengaged when the wheel speed
is greater than 40 mph (64 km/h),
if the vehicle’s battery is low and/or
the transfer case is shifted out of
4LO Lock mode.Notice:If the vehicle’s axle is
locked while driving on pavement,
the drivetrain could be damaged.
Repairs would not be covered
by the vehicle warranty. Do
not use the locking axle on
pavement. If four-wheel drive is
needed when traveling on
pavement, use only 4HI.
Locking Front Axle
For vehicles with this feature, the
locking front axle, used with
the locking rear axle, can give the
vehicle additional traction when
traveling in off-road situations such
as mud, snow, sand, steep hills
and uneven terrain.
The button used to turn the locking
front axle on or off is located on
the instrument panel.Before the front axle can be locked,
the rear axle must be locked.
To lock the front and rear axles:
1. Place the transfer case in
the 4LO Lock mode. This is the
only mode which allows the
front and rear axles to lock. See
Full-Time Four-Wheel Drive
on page 2-24for more
information regarding the transfer
case and 4LO Lock mode.
2. Press the rear axle locking
button with the vehicle moving
less than 16 mph (26 km/h).
3. Wait for the light in the button
to stop ashing and remain
illuminated to show that the rear
axle is locked.
4. Press the front axle locking
button with the vehicle stopped
or moving less than 16 mph
(26 km/h).
Driving Your Vehicle 4-9

5. Wait for the light in the button
to stop ashing and remain
illuminated to show that the front
axle is locked.
Notice:If you try to lock the axle
while the vehicle is stuck and
the tires are spinning, the
vehicle’s drivetrain could be
damaged. The repairs would not
be covered by the vehicle
warranty. Always lock the axle
before attempting situations
and/or navigating terrain which
could possibly cause the vehicle
to become stuck.
Locking axles will be disengaged
when the wheel speed is greater
than 40 mph (64 km/h), if the
vehicle’s battery is low and/or the
transfer case is shifted out of
4LO Lock mode.Notice:If the vehicle’s axle is
locked while driving on pavement,
the drivetrain could be damaged.
Repairs would not be covered
by the vehicle warranty. Do
not use the locking axle on
pavement. If four-wheel drive is
needed when traveling on
pavement, use only 4HI.
Steering
Power Steering
If power steering assist is lost
because the engine stops or the
system is not functioning, the vehicle
can be steered but it will take
more effort.
Steering Tips
It is important to take curves at a
reasonable speed.
Traction in a curve depends on the
condition of the tires and the
road surface, the angle at which the
curve is banked, and vehicle
speed. While in a curve, speed is
the one factor that can be controlled.
If there is a need to reduce speed,
do it before entering the curve,
while the front wheels are straight.
Try to adjust the speed so you
can drive through the curve.
Maintain a reasonable, steady
speed. Wait to accelerate until out
of the curve, and then accelerate
gently into the straightaway.
4-10 Driving Your Vehicle