Luggage Carrier
If the vehicle has this feature, cargo
can be loaded on top of the vehicle.
The luggage carrier consists of
siderails attached to the roof.
The crossrails attach into the
siderails and can be moved back
and forth to accommodate various
cargo sizes.
Notice:Loading cargo on the
luggage carrier that weighs more
than 250 lbs. (113 kg) or hangs
over the rear or sides of the
vehicle may damage the vehicle.
Load cargo only on top of the
crossrails and tie the cargo down
to the crossrail support cargo
tie-down loops, making sure
to fasten it securely
Do not exceed the maximum vehicle
capacity when loading your vehicle.
For more information on vehicle
capacity and loading, seeLoading
the Vehicle on page 4-35.Adjusting the Crossrails
To adjust the crossrails to t a load:
1. Turn the crossrail key
counterclockwise to unlock the
crossrail end cap.
2. Remove the end cap.
3. Pull the lever labeled “PULL”
from left to right to loosen the
crossrail.
4. Repeat Steps 1 through 3 to the
opposite end of the crossrail.5. Once both sides of the crossrail
are loose, adjust the crossrail to
the desired position.
6. Push the lever labeled “PULL”
from right to left to lock the
crossrail in place.
7. Reinstall the end cap and turn
the crossrail key to lock the
crossrail.
8. Repeat Steps 5 through 7 to the
opposite end of the crossrail.
Stop Tabs
If the vehicle has a sunroof, it has a
crossrail stop tab in the siderail.
This tab prevents the crossrail from
being moved past the opening of
the sunroof and cargo from
being loaded too far forward.
The vehicle may have cargo tie
downs. Once the cargo is loaded
onto the crossrails, use the cargo tie
downs to secure it. Do not load
cargo directly on the roof of the
vehicle. SeeCargo Tie Downs on
page 2-49for more information.
2-48 Features and Controls
If the vehicle has a brush guard,
never tow or apply any loads
onto the brush guard.
Loading the Vehicle
It is very important to know how
much weight the vehicle can
carry. This weight is called the
vehicle capacity weight and
includes the weight of all
occupants, cargo and all
nonfactory-installed options.Two labels on the vehicle show
how much weight it may
properly carry, the Tire and
Loading Information label and
the Certi cation/Tire label.
{CAUTION
Do not load the vehicle any
heavier than the Gross Vehicle
Weight Rating (GVWR), or
either the maximum front or
rear Gross Axle Weight Rating
(GAWR). If you do, parts on
the vehicle can break, and it
can change the way your
vehicle handles. These could
cause you to lose control and
crash. Also, overloading can
shorten the life of the vehicle.
Tire and Loading Information
Label
A vehicle speci c Tire and
Loading Information label
is attached to the vehicle’s
center pillar (B-pillar). With the
driver’s door open, you will
nd the label attached below the
door latch post.
Label Example
Driving Your Vehicle 4-35
The Tire and Loading
Information label shows the
number of occupant seating
positions (A), and the maximum
vehicle capacity weight (B) in
kilograms and pounds.
The Tire and Loading Information
label also shows the size of the
vehicle’s original equipment
tires (C) and the recommended
cold tire in ation pressures (D).
For more information on tires and
in ation seeTires on page 5-44
andInflation - Tire Pressure on
page 5-51.
There is also important
information on the
Certi cation/Tire label. It tells
Gross Vehicle Weight Rating
(GVWR) and the Gross
Axle Weight Rating (GAWR)
for the front and rear axles. See
“Certi cation/Tire Label” later
in this section.Steps for Determining Correct
Load Limit
1.
Locate the statement “The
combined weight of occupants
and cargo should never
exceed XXX kg or XXX lbs” on
your vehicle’s placard.
2.Determine the combined
weight of the driver and
passengers that will be riding
in your vehicle.
3.Subtract the combined weight
of the driver and passengers
from XXX kg or XXX lbs.
4.The resulting gure equals the
available amount of cargo and
luggage load capacity. For
example, if the “XXX” amount
equals 1400 lbs and there will
be ve 150 lb passengers in
your vehicle, the amount
of available cargo and
luggage load capacity is
650 lbs (1400−750
(5 x 150) = 650 lbs).
5.Determine the combined
weight of luggage and
cargo being loaded on the
vehicle. That weight may not
safely exceed the available
cargo and luggage load
capacity calculated in Step 4.
6.If your vehicle will be towing a
trailer, the load from your
trailer will be transferred to
your vehicle. Consult
this manual to determine how
this reduces the available
cargo and luggage load
capacity of your vehicle.
SeeTowing a Trailer
on page 4-42for important
information on towing a
trailer, towing safety, and
trailering tips.
4-36 Driving Your Vehicle
A.Vehicle Capacity Weight for
Example 1=1,000 lbs
(453 kg).
B.Subtract Occupant Weight
150 lbs (68 kg)×2=300 lbs
(136 kg).
C.Available Occupant and
Cargo Weight=700 lbs
(317 kg).
A.Vehicle Capacity Weight for
Example 2=1,000 lbs
(453 kg).
B.Subtract Occupant Weight
150 lbs (68 kg)×5=750 lbs
(340 kg).
C.Available Cargo
Weight=250 lbs (113 kg).
A.Vehicle Capacity Weight for
Example 3=1,000 lbs
(453 kg).
B.Subtract Occupant Weight
200 lbs
(91 kg)×5=1,000 lbs
(453 kg).
C.Available Cargo
Weight=0 lbs (0 kg).
Refer to the vehicle’s Tire and
Loading Information label
for speci c information about the
vehicle’s capacity weight and
seating positions.
Example 1Example 2Example 3
Driving Your Vehicle 4-37