2009 CHERY TIGGO relay

Downloaded from www.Manualslib.com manuals search engine 3.DETECT MALFUNCTIONING PART
• Check the following:
Fuse 17
Harness connectors C-103, E-103, terminal 1
Front fuse and relay box connector A
Harness open or short between ECM and fuse
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning parts.
4.CHECK ECM POWER SUPPLY CIRCUIT - (2)
• Check voltage between ECM terminal 64 and ground.
• Battery voltage should exist.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Check the following:
Harness connectors A-102, E-105, terminal 4
Front fuse and relay box connector A
Harness open or short between ECM and battery
5.CHECK GROUND CONNECTIONS
• Turn ignition switch off.
• Loosen and retighten ground screws on the body.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace ground connections.
6.CHECK ECM GROUND CIRCUIT FOR AN OPEN OR SHORT
• Disconnect ECM harness connector.
• Check harness continuity between ECM terminals 13, 26 and ground.
• Continuity should exist.
• Also check harness for short to power.
Is the check result normal?
Ye s>>Go to step 8.
No
>>Go to the next step.
7.DETECT MALFUNCTIONING PART
• Check harness for open or short between ECM terminals 13, 26 and ground.
• Repair open circuit or short to power in harness or connectors.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair circuit for an open or short to power in harness or connectors.
DIAGNOSIS & TESTING
03–466Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 8.CHECK ECM POWER SUPPLY CIRCUIT - (3)
• Turn ignition switch on and then off.
• Check voltage between ECM terminals

12, 25 and ground.
• Voltage: Turn ignition switch on battery voltage will be exist and after turning ignition switch off, battery voltage
will exist a few seconds, then

drop to approximately 0 V.
Is the check result normal?
Ye s>>Check the starting system.
No
>>Go to the next step.
9.CHECK STARTER RELAY SUPPLY VOLTAGE
• Turn ignition switch off. Wait for at least 10 seconds.
• Check voltage between ECM terminal 34 and ground.
• Battery voltage should exist.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Go to step 11.
10.CHECK ECM POWER SUPPLY CIRCUIT - (4)
• Disconnect ECM harness connector.
• Disconnect front fuse and relay box harness connector F.
• Check harness continuity between ECM terminals 12, 25 and front fuse and relay box terminal F3.
• Continuity should exist.
• Also check harness for short to ground and short to power.
Is the check result normal?
Ye s>>Go to step 12.
No
>>Repair circuit for an open or short in harness or connectors.
11 .CHECK STARTER RELAY CIRCUIT
• Disconnect ECM harness connector.
• Disconnect front fuse and relay box harness connector A, G.
• Check harness continuity between ECM terminal 34 and front fuse and relay box terminal A1.
• Check harness continuity between front fuse and relay box terminal A1 and G5,
• Check harness continuity between front fuse and relay box terminal A13 and G5,
• Continuity should exist.
• Also check harness for short to ground and short to power.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair circuit for an open or short to ground or short to power in harness or connectors.
DIAGNOSIS & TESTING
03
03–467Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 12.CHECK FUSE
• Disconnect fuse 12 (30A), fuse 24 (5A), fuse 25 (10A), front fuse and relay box.
• Check fuse.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace fuse 12, 23, 24.
13.CHECK FRONT FUSE AND RELAY BOX
• Check front fuse and relay box.
• Check harness continuity between front fuse and relay box and battery.
Is the check result normal?
Ye s>>Replace the ECM.
No
>>Replace or repair front fuse and relay box or harness.
DIAGNOSIS & TESTING
03–468Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 7.DETECT MALFUNCTIONING PART
• Check the following:
Fuse 25, Fuse 12, Fuse 24
Front fuse and relay box H5
Harness connectors A-102, E-105
Harness open or short between O
2sensor and fuse
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning parts.
8.CHECK O2SENSOR HEATER CONTROL CIRCUIT FOR AN OPEN AND SHORT
• Turn ignition switch off.
• Check harness continuity between ECM terminal and O
2sensor terminal.
COMPONENTS ECMO2SENSOR
TERMINAL 523
• Continuity should exist.
• Check harness short to power supply circuit and ground.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair the circuit for an open or short to power supply circuit or ground in harness or connectors.
9.CHECK O2SENSOR HEATER
• Check resistance between O
2sensor terminals.
TERMINAL NO. RESISTANCE
2 & 3 (including cable and
connector) Approximately 9

1&2and1&3 (Continuity should notexist)
4&2and4&3
Is the check result normal?
Ye s>>Go to the next step.
No
>>Replace O2sensor.
DIAGNOSIS & TESTING
03–474Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2.CHECK AIR FLOW SENSOR ELECTRICAL CONNECTOR
• Turn ignition switch off.
• Disconnect the air flow sensor electrical connector.
• Inspect the electrical connector for damage.
Is the electrical connector OK?
Ye s>>Go to the next step.
No
>>Repair or replace the electrical connector as necessary.
3.CHECK AIR FLOW SENSOR POWER SUPPLY CIRCUIT
• Turn ignition switch on.
• Check supply voltage between air flow sensor ter-
minal 4 and ground in the air flow sensor electrical
connector E-058.
• Battery voltage should exist.
Is the check result normal?
Ye s>>Go to step 5.
No
>>Go to the next step.
4.DETECT MALFUNCTIONING PART
• Check the following:
Harness connectors A-102, E-105
Front fuse and relay box H3
Fuse 22, Fuse 12
Harness open or short between air flow sensor and fuse
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning parts.
5.CHECK MAF SENSOR REFERENCE VOLTAGE
• Check reference voltage between air flow sensor terminal 7 and ground in the air flow sensor electrical connec-
tor E-058.
• 4.8 - 5.2 V should exist.
Is the check result normal?
Ye s>>Go to step 7.
No
>>Go to the next step.
DIAGNOSIS & TESTING
LTSMD030004
03–478Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2.CHECK CRANKSHAFT POSITION (CKP) SENSOR ELECTRICAL CONNECTOR
• Disconnect the CKP electrical connector (1).
• Inspect the electrical connector for damage.
Is the electrical connector OK?
Ye s>>Go to the next step.
No
>>Repair or replace the electrical connector
as necessary.
3.CHECK CRANKSHAFT POSITION (CKP) SENSOR POWER SUPPLY CIRCUIT FOR AN OPEN OR SHORT
• Turn ignition switch on.
• Check supply voltage between CKP sensor terminal
3 and ground in the CKP sensor electrical connec-
tor E-055.
• Battery voltage should exist.
Is the check result normal?
Ye s>>Go to step 5.
No
>>Go to the next step.
4.DETECT MALFUNCTIONING PART
• Check the following:
Fuse 22, Fuse 12
Front fuse and relay box H3
Harness connectors A-102, E-105
Harness open or short between CKP sensor and fuse
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning parts.
DIAGNOSIS & TESTING
LTSMD030079
LTSMD030012
03–500Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4.DETECT MALFUNCTIONING PART
• Check the following:
Fuse 22, Fuse 12
Front fuse and relay box H3
Harness connectors A-102, E-105
Harness open or short between CMP sensor and fuse
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning parts.
5.CHECK THE CMP SENSOR GROUND CIRCUIT FOR AN OPEN
• Turn ignition switch off.
• Check harness continuity between following terminals.
CKP
SENSOR
TERMINAL TERMINAL CONTINUITY
1
Ground Yes
• Continuity should exist.
Is the check result normal?
Ye s>>Go to step 7.
No
>>Go to the next step.
6.DETECT MALFUNCTIONING PART
• Check harness for open or short between CMP sensor and ground.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace the circuit for an open or short in harness or connectors.
DIAGNOSIS & TESTING
03
03–507Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 6.CHECK INJECTOR POWER SUPPLY CIRCUIT FOR OPEN OR SHORT
• Turn ignition switch on.
• Check injector supply voltage between sensor ter-
minal 1 and ground in the electrical connector.
• Battery voltage should exist.
Is the check result normal?
Ye s>>Go to step 8.
No
>>Go to the next step.
7.DETECT MALFUNCTIONING PART
• Disconnect injector harness connector.
• Check the following:
Harness connectors A-102, E-105
Front fuse and relay box H3
Fuse 22, Fuse 12
Harness for open or short between injector and fuse
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace malfunctioning part.
8.CHECK INJECTOR CONTROL CIRCUITS FOR AN OPEN AND SHORT
• Turn ignition switch off.
• Disconnect ECM harness connector.
• Check harness continuity between following terminals.
INJECTOR
NO. ECM
TERMINAL INJECTOR
TERMINAL
112
21 42
322
41 52
DIAGNOSIS & TESTING
LTSMD030019
03–522Chery Automobile Co., Ltd.