2008 NISSAN TIIDA bearing

MT-24
< SERVICE INFORMATION >
TRANSAXLE ASSEMBLY
6. Remove the bolts.
7. Remove reverse idler shaft bolt ( ) and seal washer.
8. Remove transaxle case (1) upward while rotating control lever
(2).
9. Remove spring (1) of selector from return bushing (2).
10. Remove bearing preloading shim from mainshaft assembly.
11. Move 1st-2nd fork rod (1), 3rd-4th and 5th-6th fork rod (2), and
reverse fork rod (3) to neutral position.
12. Remove selector (4) from clutch housing.
PCIB1694E
PCIB1695E
PCIB1696E
PCIB1697E
PCIB1698E

MT-26
< SERVICE INFORMATION >
TRANSAXLE ASSEMBLY
20. Remove differential side oil seals (1) from clutch housing and
transaxle case using suitable tool.
CAUTION:
Be careful not to damage clutch housing and transaxle
case.
21. Remove differential side bearing outer race (1) from clutch hous-
ing using suitable tool.
CAUTION:
Be careful not to damage clutch housing.
22. Remove differential side bearing outer race (1) and shim (2)
from transaxle case using a brass bar as shown.
CAUTION:
Be careful not to damage transaxle case.
23. Remove retaining pin from control lever (1) using suitable tool.
24. Remove control lever.
25. Remove shift finger (1) from transaxle case.
PCIB1704E
PCIB1716E
PCIB1705E
PCIB1711E
PCIB1712E

TRANSAXLE ASSEMBLY
MT-27
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
MT
N
O
P
26. Remove control lever oil seal and bushings from transaxle case
using suitable tool.
27. Remove oil gutter (1) from transaxle case.
28. Remove shift lever oil seal (1) from transaxle case.
29. Remove bushings (1) from transaxle case using suitable tool.
30. Remove mainshaft rear bearing outer race and shim from tran-
saxle case using suitable tool.
CAUTION:
Be careful not to damage transaxle case.
PCIB1713E
PCIB1707E
PCIB1709E
PCIB1710E
PCIB1706E

MT-28
< SERVICE INFORMATION >
TRANSAXLE ASSEMBLY
31. Remove snap ring (1) and oil channel (2) from transaxle case.
32. Remove input shaft oil seal (1) from clutch housing using suit-
able tool.
33. Remove mainshaft front bearing outer race (1) and oil channel
(2) from clutch housing using Tool (A) and suitable tool (B).
34. Remove busings (1) from clutch housing using suitable tool.
35. Remove two way connector (1) from clutch housing.
PCIB1708E
PCIB1714E
Tool number : KV381054S0 (J-34286)
PCIB1718E
PCIB1717E
PCIB1720E

MT-30
< SERVICE INFORMATION >
TRANSAXLE ASSEMBLY
4. Install oil channel and mainshaft front bearing outer race into
clutch housing using Tool (A).
CAUTION:
Do not reuse oil channel.
5. Install input shaft oil seal (1) into clutch housing using Tool (A).
6. Install snap ring (1) and oil channel (2) onto transaxle case.
7. Install shim and mainshaft rear bearing outer race into transaxle
case using Tool (A).
8. Install bushings (1) into transaxle case using suitable tool (A).Tool number : KV38100200 ( — )
PCIB1724E
Tool number : ST33220000 ( — )
PCIB1721E
PCIB1729E
Tool number : KV38100200 ( — )
PCIB1728E
PCIB1727E

TRANSAXLE ASSEMBLY
MT-31
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
MT
N
O
P
9. Install oil gutter (1) onto transaxle case.
10. Install shift lever oil seal (1) and bushing (2) into transaxle case
using suitable tool (A).
11. Install control lever oil seal and bushings into transaxle case
using suitable tool.
12. Install shift finger (1) into transaxle case.
13. Install control lever (1) and then install retaining pin.
CAUTION:
Do not reuse retaining pin.
14. Install shim and differential side bearing outer race into transaxle
case using Tool (A).
PCIB1730E
PCIB1731E
PCIB1712E
PCIB1711E
Tool number : ST33400001 (J-26082)
PCIB1726E

MT-32
< SERVICE INFORMATION >
TRANSAXLE ASSEMBLY
15. Install differential side bearing outer race into clutch housing
using Tool (A).
16. Install differential side oil seals (1) into clutch housing and tran-
saxle case using Tool (A).
17. Install magnet onto clutch housing.
18. Install final drive assembly into clutch housing.
19. Install input shaft assembly (1), mainshaft assembly (2) and 1st-
2nd fork rod assembly (3) into clutch housing.
20. Install spring washer located under the reverse idler shaft.
21. Install reverse gear assembly (1) according to the following:
a. Lift up the input shaft assembly (2) and mainshaft assembly (3).
b. Install reverse gear assembly (1) and reverse fork rod (4) to
clutch housing.
22. While lifting up fork rod (1), install 3rd-4th and 5th-6th fork rod
assembly to clutch housing. Tool number : KV38100200 ( — )
PCIB1722E
Tool number : KV38100300 (J-25523)
PCIB1732E
PCIB1702E
PCIB1701E
PCIB1700E

TRANSAXLE ASSEMBLY
MT-33
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
MT
N
O
P
23. Install retaining pin into 5th-6th shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin.
24. Move 1st-2nd fork rod (1), 3rd-4th and 5th-6th fork rod assembly
(2), and reverse fork rod (3) to neutral position.
25. Install selector (4) into clutch housing.
26. Install spring of selector into return bushing.
27. Install bearing preloading shim onto mainshaft assembly.
28. Apply recommended sealant onto the mating surface of tran-
saxle case.
•Use Genuine Silicone RTV or equivalent. Refer to GI-42,
"Recommended Chemical Product and Sealant".
CAUTION:
• Remove old sealant adhering to the mating surfaces. Also
remove any moisture, oil, or foreign material adhering to both mating surfaces.
• Check for damage on the mating surface.
• Apply a continuous bead of liquid gasket to the mating surface.
29. Engage shift finger and selector by moving control lever (1).
Install transaxle case to clutch housing.
30. Install seal washer and reverse idler shaft bolt ( ), and then
tighten bolt to specification.
CAUTION:
Do not reuse seal washer.
PCIB1699E
SCIA7782E
SCIA7783E
PCIB1695E