2008 MITSUBISHI SHOGUN engine

Starting and driving
4-57
4
Wa r n i n g l a m p●
The brake warning lamp illuminates to indicate a fault in the braking system. Read “Brake warning lamp” on page 3-13.
●
On vehicles with the rear di
fferential lock, the active sta-
bility & traction control (AST
C) and anti-lock brake sys-
tem (ABS) functions are
suspended while the rear
differential lock is activat
ed. ASTC indication lamp,
active stability control function OFF indication lamp, ABS warning lamp and brake warning lamp are illumi- nated while these functions are suspended. It does notindicate a problem. When the re
ar differential lock is dis-
engaged, these lamps go out and function again. Refer to “Brake warning lamp” on page 3-13, “ABSwarning lamp” on page 4-60, “ASTC indication lamp” on page 4-64, “Active stability control function OFF indica- tion lamp” on page 4-67.
When brakes are wetCheck the brake system while dr
iving at a low speed immedi-
ately after starting, especially wh
en the brakes are wet, to con-
firm they work normally. A film of water can be formed
on the brake discs and prevent
normal braking after driving in heavy rain or through largepuddles, or after the vehicle is washed. If this occurs, dry the brakes out by driving slowly while lightly depressing the brake pedal.When driving downhillIt is important to take advantage of the engine braking by shift-ing to a lower shift position while driving on steep downhill roads in order to prevent th
e brakes from overheating.
WARNING
!●
Never coast downhill with
the engine OFF. Keep the
engine running whenever your
vehicle is in motion.
If you turn off the engine
while driving, the power
brake booster will stop
working and your brakes
will not work as well.
●
If the power assist is lost
or if either brake hydraulic
system stops working properly, have your vehicle checked immediately.
WARNING
!●
Do not leave any objects near the brake pedal or let a floor mat slide
under it; doing so could prevent the
full pedal stroke that would be necessary in an emer-gency. Make sure that the pedal can be operated freely at all times. Make sure the floor mat is securely held in place.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
57 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-59
4
●
Operation of ABS is not rest
ricted to situations where
brakes are applied suddenly. Th
is system may also operate
to prevent wheel lock when
you are driving over man-
holes, steel road-work plates,
or the vehicle is driven over
steps or level differences in
the road, road markings, or
other surfaces which are diffic
ult for the wheels to grip.
●
When the ABS is activated, you may feel the brake pedal pulsation and the vibrations of the vehicle body and steer- ing wheel. You may also hear
a characteristic noise. At
this time, you may feel as if the pedal attempts to resistbeing depressed. This is a normal result of the ABS operation, and does not indicate a problem.In this situation, to let the ABS work for you, just hold the brake pedal down more firmly. Do not pump the brake. This will result
in reduced braking perform-
ance.
●
When the engine starts and
after starting to drive, you
might hear operation noise fr
om the engine compartment
or feel a shock from the brake pedal. This is normal. The ABS is performing a self-check.
●
The ABS will operate after the vehicle has accelerated to a speed in excess of approximately 10 km/h (6 mph). It stops operating when the vehi
cle decelerates to low speed
below approximately 5 km/h (3 mph).
CAUTION
!●
Even the ABS cannot prevent the natural laws of physics from acting on th
e vehicle. It cannot for
instance avoid accidents that
may result from exces-
sive speed on bends or fo
llowing another vehicle too
closely or aquaplaning. It should remain the driver’stask to observe safety pr
ecautions to judge speeds
and brake applications corr
ectly in such conditions.
●
Be sure to use tyres of the same type and size on 4 wheels. If tyre types or sizes are mixed, ABS may not func- tion normally.
●
Never install a limited slip
differential, which is not
MITSUBISHI MOTORS genuine parts, as the ABSmay not function normally. We recommend you to consult a MITSUBISHI MOTORS Authorized
Service Point.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
59 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-61
4
If the warning lamp illuminates while driving
E00607300416
If only the ABS warning lamp illuminates●
Avoid hard braking and high-speed driving. Stop the vehi- cle in a safe place. Restart the engine and check to see whether the lamp goesout after a few minutes driving; if it then remains off dur- ing driving, there is no problem. However, if the lamp does not go out, or if it lights upagain when the vehicle is driven, we recommend you to have the vehicle checked as soon as possible.
●
The ABS warning lamp can illuminate if the battery volt- age is insufficient when the en
gine is started. In this case,
it does not indicate an ABS fault. Charge the battery by allowing the engine to idle for awhile. If the battery has been charged but the ABS warning lamp continues to illuminate or illuminates intermittently, werecommend you to have the vehicle inspected.
If the ABS warning lamp and brake warning lamp illu- minate at the same time●
The ABS and brake force distribution function will not work, so hard braking could make the vehicle unstable. Avoid hard braking and high-speed driving. Stop the vehi- cle in a safe place and we recommend you to have thevehicle checked.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
61 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-63
4
Power steering system
E00607400084
When the engine is stopped, the
power steering system will not
function and it will require greater
manual effort to operate the
steering wheel. Keep this in mind
in particular when towing the
vehicle. Never turn off the engine while driving. Periodically check the power steering fluid level.
Active stability & traction control (ASTC)
E00613800168
The active stability & traction
control (ASTC) takes overall
control of the anti-lo
ck brake system, active stability control
function and active traction control function to maintain thevehicle’s stability and traction.
Please read this section in con-
junction with the pages on the
anti-lock brake system, active
stability control function and
active traction control function.
Anti-lock brake
system (ABS)
→ p. 4-58
Active stability control function
→ p. 4-66
Active traction control function
→ p. 4-68
CAUTION
!●
Do not hold the steering
wheel in the fully turned
position (either left or ri
ght), for long
er than 10 sec-
onds.This can cause damage to
the power steering system.
CAUTION
!●
Do not over-rely on the
ASTC. Even when the ASTC
is operating, there are limits to how far it can ensure vehicle stability; reckless driving may lead to acci-dents. Always drive carefully, taking account of the road conditions.
●
Be sure to use the same specified type and size of tyre on all 4 wheels. Otherw
ise, there is a possibility
that the ASTC will
not work properly.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
63 Wednesday, January 9, 2008 4:36 PM

4-64 Starting and driving
4
NOTE●
An operation noise may be emitted from the engine com- partment in the following situations. The sound is associ- ated with checking the operat
ions of the ASTC. At this
time, you may feel a shock from the brake pedal if youdepress it. These do not indicate a malfunction. • When the ignition switch is set to the “ON” position. • When the vehicle is driven for a while after the engine isturned on.
●
When the ASTC is activated,
you may feel a vibration in
the vehicle body or hear a whining sound from the enginecompartment. This indicates that the syst
em is operating normally. It
does not indicate a malfunction.
●
When the anti-lock brake syst
em warning lamp is illumi-
nated, the ASTC is not active.
●
On vehicles with the rear di
fferential lock, the ASTC and
ABS functions are suspended while the rear differential lock is activated. ASTC indication lamp, active stability control function OFF indication lamp, ABS warning lampand brake warning lamp are ill
uminated while these func-
tions are suspended. It does not indicate a problem. When the rear differential lock is
disengaged, these lamps go out
and function again. Refer to “Brake warning lamp” on page 3-13, “ABS warning lamp” on page 4-60, “Active stability controlfunction OFF indication lamp” on page 4-67.
ASTC indication lamp
E00618000035
The ASTC indication lamp shows the operating status of theactive stability control function and active traction control function. For details, see these sections of this owner’s manual: Active stability control function indication lamp
→ p. 4-67
Active traction control function indication lamp
→ p. 4-69
BK-BK2008E1ENUK.en-uk-Section7.fm Page
64 Wednesday, January 9, 2008 4:36 PM

4-66 Starting and driving
4
Driving hints
E00618100036
When extricating the vehicle
from mud, sand or fresh snow
with the transfer shift lever in the “2H”, “4H”, or “4HLc” posi- tion, you may find that operation of the ASTC prevents the engine speed from increasing in
response to depression of the
accelerator pedal. If this happens
and the vehicle remains stuck
as a result, place the transfer sh
ift lever in the “4LLc” position
or turn the active stability cont
rol switch OFF. The vehicle will
then be easier to extricate. (Bra
ke control of the active traction
control function is still working to prevent wheel spins when ASC OFF switch “OFF” or
“4LLc” position selected.)
NOTE●
If the vehicle speed increases
to about 120 km/h (75 mph)
with the active stability cont
rol function deactivated, the
active stability control function automatically starts oper-ating. To subsequently stop the active stability control function, stop the vehicle
and press the ASC OFF switch
again.
Active stability control function
E00613900097
The active stability control function is designed to help main-tain the vehicle’s control in slippery conditions, or during rapid steering maneuvers. It works by controlling the engine output and brake on each wheel.NOTE●
The active stability control function does not operate when the transfer shift lever is in the “4LLc” position. When the active stability control function is operatingwith the transfer shift lever
in the “2H”, “4H” or “4HLc”
position, moving the shift lever to the “4LLc” position makes the active stability cont
rol function d
eactivate auto-
matically.
●
On vehicles with rear differ
ential lock, th
e active stability
control function does not operate when the rear differen-tial lock is activated.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
66 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-67
4
Active stability control function indication lamp
E00614000125
The indication lamps should illuminate when the ignition switch is turned to the “ON” position and should go off after a few seconds.If the indication lamps stay on or do not illuminate when the ignition switch is turned to the “ON” position, we recommend you to have your vehicle inspected.
indication lamp blinks when
the active stability control
function is operating.
indication lamp illuminates when the active stability control
function is deactivated by either of the following operations: ●
The ASC OFF switch is presse
d to deactivate the system.
●
The transfer shift lever is
placed in the “4LLc” position.
Active stability control function indication lamp Active stability control function OFF indication lamp
CAUTION
!●
When indication lamp bl
inks, the active stability
control function is operating, which means that the road is slippery or that
your vehicle’s wheels are
spinning excessively. If this happens, drive slower with less accelerator input.
●
If a fault occurs in th
e device, the ABS warning
lamp or and indication lamps illuminate as warning. Park your vehicl
e in a safe place and stop
the engine. Then, start the engine again and check whether the ABS warning la
mp or and indica-
tion lamps go out. If the ABS warning lamp or and indication lamps remains lit even af
ter the engine has been
started, we recommend you to have your vehicle checked.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
67 Wednesday, January 9, 2008 4:36 PM

4-68 Starting and driving
4
NOTE●
Immediately after reconnecti
on of the battery cable, the
indication lamp will illuminate and the active stability
control function will stop operating. If the vehicle is driven and the indication la
mp goes off, the active sta-
bility control function will again start operating. If the indication lamp illuminates again or illuminates even though the battery has not been disconnected, aninsufficient battery voltage or other problems may be the reason. We recommend you to have your vehicle inspected.
Active traction control function
E00614100041
The active traction control function maintains traction on slip-pery road surfaces by automatical
ly controlling the engine out-
put and applying the brakes
so the driving wheels are
prevented from spinning.The active traction control f
unction automatically turns ON
when the ignition switch is turned to the “ON” position.
CAUTION
!●
If the temperature in the
braking system increases
excessively due to conti
nuous brake control on a
slippery road surface,
a warning buzzer will sound
intermittently to warn the
driver. If driving contin-
ues in spite of the buzzer an
d the temperature in the
braking system increases
further, the indication
lamp will illuminate, th
e warning buzzer will sound
continuously for approx
imately 3 seconds, and
active traction control function operation will besuspended to protect the
braking system. (Normal
operation of the ve
hicle will not be
affected.) If the
vehicle is stopped and the indication lamp goes off, the active traction control function will start operating again.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
68 Wednesday, January 9, 2008 4:36 PM