2008 MITSUBISHI SHOGUN display

Instruments and controls
3-31
3
Clock-only
E00518900017
Only the clock is shown. The time notation can be changed to the setting you desire. (12 hour / 24 hour) Refer to “User customization” on page 3-46.
Blank
E00519000015
The whole display can be turned into blank. In this case, but- tons remain illuminated.NOTE●
If you operate the audio sy
stem, the audio display pops
up.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
31 Wednesday, January 9, 2008 4:32 PM

3-32 Instruments and controls
3
Selecting settings displays
E00519100045
Every time the “ADJ” button is pressed lightly, the display can be changed to the following:
CAUTION
!●
The driver should not opera
te the display while the
vehicle is in motion.
●
When operating the system,
stop the vehicle in a safe
area.
1- Changing the clock settings
→ p. 3-33
2- Adjusting the display brightness
→ p. 3-35
3- Correcting the compass*
→ p. 3-37
4- Changing the calendar setting
→ p. 3-42
5- User customization
→ p. 3-46
6- Adjusting the barometer
→ p. 3-54
BK-BK2008E1ENUK.en-uk-Section6.fm Page
32 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-33
3
Changing the clock settings
E00519200017
1. Press the “ADJ” butto
n to select the clock setting display.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
33 Wednesday, January 9, 2008 4:32 PM

3-34 Instruments and controls
3
2. It is possible to adjust the clock using the function buttons
3. After making the adjustment, press the “INFO” button to
select the information display.
NOTE●
Vehicles equipped with the Mitsubishi Multi Communica- tion System (MMCS) also have a clock indication, but the time shown by the MMCS may differ from that shown by the centre information disp
lay because different sources
of data are used for automatic adjustment.
“H”- Adjust “hour”.
The indication increases by one hour, every time youlightly press the “H” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the hour selected.
“M”- Adjust “minute”.
The indication increases by one minute, every time youlightly press the “M” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the minute selected.
“SET”- To reset the minutes to zero.
The time is adjusted as described below by pressing thefunction button “SET”.●
10:30-11:29 · · · · Change to 11:00
●
11:30-12:29 · · · · Change to 12:00
In this occasion, the display flashes twice before the set-ting is changed.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
34 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-35
3
Adjusting the display brightness
E00519300018
The display brightness can be adjusted at 13 levels for both daytime and nighttime. ●
BRIGHTNESS FOR DAYTIME The display brightness is adjusted when the light switch is in the “OFF” position.
●
BRIGHTNESS FOR NIGHTTIME The display brightness is adjusted when the light switch is in the “ ” or “ ” position.
1. Press the “ADJ” button to sh
ow the brightness adjusting
display.
2. Press the “
←” or “
→” function button to select the setting
you wish to adjust (daytime or nighttime). Then press the “SELECT” function button.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
35 Wednesday, January 9, 2008 4:32 PM

3-36 Instruments and controls
3
3. Use the function buttons to adjust the brightness.
NOTE●
If you next wish to adjust the other adjustment setting (daytime or nighttime), press the “ADJ” button or “BACK” function button.
4. After adjustment, press the
“INFO” button to select the
information display.
NOTE●
As the display brightness can
be adjusted in the center
information display only, the brightness inside the meter cannot be changed.
“+”- To make the display brighter
The display becomes brighter by one step, every timeyou lightly press the “+” function button. If you con-tinue pressing the button for about 2 seconds or more,the indication is fast-forwarded.
“-”- To make the display darker
The display becomes darker by one step, every time youlightly press the “-” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded.
“SET”- To set the brightness
Press function button “SET” to set the new brightness.The display will flash twice.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
36 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-37
3
Correcting the compass
*
E00519400080
This compass shows the directi
on of the vehicle by the 8 azi-
muth system.
NOTE●
This system uses the earth’s magnetic field, and so may not show the correct direction depending on the traffic condition or in the following places where the earth’s magnetic field is disrupted.· Car parks located in buildings and tunnels · Expressways and underground cables · Area over the subway· Transforming station · Areas along the railroad In these cases, the correct dir
ection will be displayed once
the vehicle returns to a place where the earth’s magnetic field is stable.
●
Do not install ski racks, ante
nnas, etc. which are attached
to the vehicle by means of a ma
gnet. They affect the oper-
ation of the compass.
●
On vehicles equipped with the Mitsubishi Multi Commu- nication System (MMCS), even though the compass set- ting display is shown, correcting the compass will not be possible.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
37 Wednesday, January 9, 2008 4:32 PM

3-38 Instruments and controls
3
Setting the declination The declination is the difference
between true north (the direc-
tion of the geographic north po
le) and where a compass needle
points to. Since the declination
varies from place to place, it
needs to be set for each region
. Otherwise the compass will not
show the correct direction. Set the declination by the following steps:NOTE●
The default declination settin
g is 0 degrees. In accordance
with the illustration, set the declination setting to the dec- lination contour nearest to a region where you drive thevehicle.
●
The declination can be set at
intervals of 1 degrees, from
28 degrees west (W28) to 28 degrees east (E28).
With a settings display showing, press the “ADJ” button and select “COMPASS VARIANCE”. 1. Press the function button for “SELECT”.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
38 Wednesday, January 9, 2008 4:32 PM