2008 GREAT WALL FLORID lock

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual232
Airbag’s Diagnostic Methods Without a Diagnostic Scanner
Airbag indicator lamp warning
Check the airbag ECU connectors for looseness, check for warnings after correct installation.
Inspect whether the clock spring is conducting
Go to a professional maintenance station to perform inspection
Disconnect the front passenger side seat belt pretensioner wires and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Disconnect the driver side seat belt pretensioner wires and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Disconnect the front passenger side airbag line and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
D i s c o n n e c t t h e d r i v e r s i d e a i r b a g l i n e a n d replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Check whether the alarm continues after replacing the clock spring
No
No
No
No
NoNo
Yes
Yes

Downloaded from www.Manualslib.com manuals search engine 233Vehicle Body
Front Door Lock Assembly ...............................................234
Rear Door Lock Assembly ................................................237
Trunk Door Lock Assembly ...............................................239
Wiper Arm and Vent Panel Assembly ...............................240
Front & Rear Window Glasses .........................................241
Dashboard ........................................................................\
242
Cooling Unit ......................................................................246
Front Door Assembly ........................................................248
Rear Door Assembly.........................................................251
Trunk Door Assembly .......................................................254
Front Bumper....................................................................256
Rear Bumper ....................................................................259
Seat Belt ........................................................................\
...262
Seats ........................................................................\
........266
Sunroof Assembly.............................................................268
Vehicle Body

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual234
Front Door Lock Assembly
Components
Front door lock installation and removal
1. Install the outside handle framework.
Install the door lock tie rod on the outside handle's framework,
install the outside handle framework, and tighten
the mounting screw.
2. Install the gasket.
3. Install the outside handle of the front door on the out-
side handle framework.
Inside handle assembly
Front door lock assembly LH
Lock mounting screw
Gasket
Front door locking cable installing buckle
Front door unlock cableFront door lock cable
Front door lock latchFront door lock cylinder assembly LH
Lock cylinder decorative cap
Front door outside handle
Gasket
Front door outside handle framework
Front door tie rod assembly
Q2580820 + Q141F32
Framework mounting screw
Door lock tie rod
Front door outside handle
Gasket mounting hole

Downloaded from www.Manualslib.com manuals search engine 235Vehicle Body

4. Separate installation for the front door lock assembly.
Separately install the front door lock, lock cable, unlock
cable, cable installing buckle, and side door inside handle
assembly. On the left is the schematic diagram after installa-
tion.
7. Install the inside handle.
Clamp the inside handle clip to the door inner decoration
board, and then firmly press the inside handle clip dowel pin
into the mounting hole.
8. Install the front door lock cylinder.
Clip the decorative cap of the driver side door onto the lock
cylinder, install the lock cylinder into the lock hole, and then
tighten the lock cylinder’s mounting screw.
5. Install the front door lock assembly.
Install the assembled assembly, tighten the lock mounting
screws (pay attention to put the outwardly opened tie rod in
and block the lock's outwardly opened swing arm lever clip
sheath), and insert the wire harness plug-in into door lock
socket.
6. Install the cable buckle.
Install the buckle in the door inner decoration board, and put
the cable in the buckle.
9. Install the door lock inside handle screws.
When the door cylinder panel assembly is installed, tighten
the inside handle's mounting screw.
Door lock socket
Inside handle dowel pinInside handle clip
Lock cylinder decorative cap
Lock cylinderMounting screw
Mounting screw
Door lock inside handle

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual236
10. Install the door lock latch.
11. Front door lock removal.
For the removal, please simply reverse the installation steps.
Caution: The front door tie rod can be removed following
the outside handle framework. The front door tie rod
can be removed after the removal of the outside handle
framework.
Door lock latch
Q2580820 + Q141F32

Downloaded from www.Manualslib.com manuals search engine 237Vehicle Body
Rear door lock installation and removal
1. Install the outside handle framework, and tighten the
framework mounting screw.
Rear Door Lock Assembly
Components
2. Install the gasket.
P u t t h e g a s k e t o n t o t h e m o u n t i n g h o l e ( s i m i l a r t o t h e
installation for the front door).
3. Install the rear door outside handle on the outside han-
dle framework.
4. Separate installation for the rear door lock assembly.
Separately install the rear door lock, lock cable, unlock
cable, cable installing buckle, and rear door inside handle as-
sembly (similar to the installation for the front door).
Rear door outside handle
Rear door lock latch
Rear door lock cable installing buckle
Rear door lock assembly LH
Lock mounting screw
Rear door inside handle assembly LH
Rear door handle decorative cap
Rear door outside handle framework LH
Rear door outside handle gasket
Rear door outside handle gasket 2
Q2580816
Framework mounting screw
Gasket
Rear door outside handle

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual238
5. Install the rear door lock assembly.
Install the assembled assembly, tighten the lock mounting
screws (pay attention to put the outwardly open swing arm
lever clip of the lock onto the outer opened fork of the out-
side handle framework), and then insert the wire harness
plug-in into the door lock socket.
6. Install the cable buckle.
7. Install the inside handle.
Clamp the inside handle clip to the door inner decoration
board, and then firmly press the inside handle clip dowel pin
into the mounting hole.
8. Install the rear door outside handle decorative cap, and
tighten the decorative cap mounting bolt.
9. Install the inside handle screw.
When the door cylinder panel assembly is installed, tighten
the inside handle's mounting screw.
10. Install the rear door lock latch.
11. For rear door lock removal, please simply reverse the
installation steps.
Door lock fork
Inside handle dowel pin
Inside handle clip
Mounting screw
Door lock inside handle
Rear door lock latch
Q2580822

Downloaded from www.Manualslib.com manuals search engine 239Vehicle Body
Trunk door lock installation and removal
1. Install the trunk door outside handle.
Install the trunk door outside handle assembly, tighten the
mounting screw, and install the wire harness plug-in.
Trunk Door Lock Assembly
Components
2. Install the trunk door main lock assembly.
Install the trunk door main lock assembly, and tighten the
mounting screw.
3. Install the trunk lock latch.
4. For trunk lock removal, please simply reverse the
installation steps.
Trunk door lock assembly
Q1460620 (Q402) F3
Trunk door lock latch
Q2580820 + Q141F32
Q1840616F3
Trunk door outside handle assemblyConnect the central door lock controller
Connect the door lamp indicator
Q1460620 (Q402) F3
Connect the door lamp indicator
Connect the central door lock controller
Q1840616F3