Page 268 of 281

Downloaded from www.Manualslib.com manuals search engine 261Vehicle Body
7. Remove the front bracket.
Screw off the cross slot & concave hexagon head self-tap-
ping screw and large washer subassembly on the left & right
front mounting bracket of the rear bumper, and pull the left
& right front mounting bracket of rear bumper out.
8. Remove the rear bracket.
Screw off the cross slot & concave hexagon head self-tap-
ping screw and large washer subassembly on the left & right
rear mounting bracket of the rear bumper, and pull off the
left & right rear mounting bracket of the rear bumper.
Engine hood lock cable removal and installa-
tion
Removal
1. Open the engine hood.
2. Remove the engine hood release lever from the dash-
board.
3. Remove the cable from the engine hood release lever
4. Remove the bolts and engine hood lock latch release
mechanism.
5. Remove the cable from the engine hood lock latch re-
lease mechanism assembly.
Installation
Areas of Importance: Different metals making direct
contact will accelerate corrosion. Make sure to use the
correct fastening piece to avoid premature corrosion.
1. Install the cable onto the engine hood lock latch re-
lease mechanism assembly.
2. Install the engine hood lock latch release mechanism
assembly with the bolts.
3. Install the cable onto the engine hood lock latch re-
lease lever.
4. Install the engine hood release lever onto the dash-
board.
Rear bumper body
Rear bumper body
Rear mounting bracket LH of the rear bumper
Cross slot & concave hexagon head self-tapping screw and large washer subassembly
Front mount-ing bracket LH of the rear bumper
Cross slot & concave hexagon head self-tap-ping screw and large washer subassembly
Engine hood lock latch release mechanism
Cable
Bolt
Dashboard
Release lever
Page 272 of 281

Downloaded from www.Manualslib.com manuals search engine 265Vehicle Body
3. Install the C-pillar protector.
General Instructions and Operations of Seat Belt
Front seat belt warning:
The front seat belts are equipped with seat belt indicator. The driver seat belt indicator is located on the dash-
board and that of the front passenger is on the air conditioner panel. If the ignition switch is on but the front pas-
senger does not fasten the seatbelts, the indicator will turn on.
Preload three-point type belt retractor:
The front seat belts utilize preload three-point type belt retractors. The preload three-point type belt retractor is
loose, enabling the passenger to move freely unless there is an emergency, such as emergency braking, hard ac-
celeration, or hard turning.
Operation notice and function examination:
Areas of Importance
If the seat belt retractor is installed incorrectly, the seat belt will lose its function in the event of an accident, and
thus fail to protect the passenger!
Prevent sharp and harmful substances from touching the seat belt.
Avoid winding or breaking the seat belt lock tongue and seat belt lock bu\
tton.
Do not bleach or dye the seat belt woren band. Wash it with neutral liquid soap and water only.
Before installing the seat belt mounting bolt, manually tighten the seat\
belt bolts to avoid improper clipping.
Do not repair the seat belt retractor or seat belt lock button. If the seat belt is broken, the seat belt assembly must
be replaced.
Change the broken or damaged seat belt.
Function examination:
1. Check whether all the seat belt mounting bolts are tightened.
2. Check the seat belt lock button. The lock button should be unlocked and able to lock easily.
3. After locking the seat belt, the seat belt lock tongue can no longer loo\
sen.
4. Pull all the seat belts out. Seat belts cannot have knots or tears.
5. The belt should retract smoothly but not roughly.
Warning:
Different metals making direct contact will accelerate corrosion. Make sure to use the correct fastening
piece to avoid premature corrosion!
4. Install the seat belt lower mounting bolt.
Lower mounting bolt
Side sheet metal
C-pillar protector
Page 276 of 281

Downloaded from www.Manualslib.com manuals search engine 269Vehicle Body
Fault classificationFault symptomFault diagnosisFault maintenance
Window panel
motion failure
Window panel (sunroof)
cannot open, rise, or close
from its initial position
Check if anything is blocking the guide rail
for window panel movement. Check whether
the mechanism moves smoothly or stiffly.
Check whether the mechanism is broken.
Check whether the guide rail is deformed.
Check whether the motor works normally.
Replace the sunroof guide rail assem-
bly. Replace the motor.
The window panel can-
not close while half-
opened or half-tilted
Diagnosis: Check whether there are oddities
impeding the window panel's movement .
Check whether the wind guard or rear roof
drip channel is arched or deformed.
Clean the objects and close the sun-
roof by force when the jam protection
function is started, then open it again
for operation. Replace the wind guard
and rear roof drip channel.
Sun visor push/pull
fault
Sun visor cannot open
or close normally
Check whether the guide rail for the sun visor
is blocked by oddities. Check whether the sun
visor bracket is broken.
Clean the oddities in the guide rail.
Change the sun visor. Change the sun
visor bracket.
The sun visor cannot open
and close completely
Check whether the front part of sun visor
arches. Check whether the sun visor lever has
been broken off.
Replace the sun visor. Replace the
sun visor lever.
Sunroof leakage fault Sunroof leakageCheck the clearance between the window
panel and the car roof hatch.
Adjust and enlarge the window panel
weatherstrip.
Check whether a build up of sand or dust ex-
ists on the surface of window panel weather-
strip.
Clean the weatherstrip surface and
car roof hatch.
Check the sealing conditions between the
guide rail & front roof drip channel and rear
roof drip channel.
Replace the sunroof guide rail assem-
bly.
Check whether the front roof drip channel
and rear roof drip channel are broken.
Replace the sunroof guide rail assem-
bly or rear roof drip channel.
Abnormal noiseThere is abnormal noise
when closing the sunroof
(1) Check the positioning of the closed win-
dow panel.
(2) Check whether the wind deflector spring is
in the right position.
(3) Check whether the rear roof drip channel's
fixed spring has broken off.
(4) Check whether the wind deflector buffer
rubber block has broken off.
(1) Adjust the window panel's position.
(2) Place the wind deflector spring in
the right position .
(3) Re-install the fixed spring.
(4) Re-install the rubber block.
There is abnormal
noise when the sun-
roof is operating
(1) Check whether the motor is working nor-
mally.
(2) Check whether oddities exist in the guide
rail for mechanism movement .
(3) Check the grease's conditions on the mov-
ing components .
(4) Check whether the moving components
are broken.
(1) Replace the motor.
(2) Clean out any contamination.
(3) Lubricate the components.
(4) Replace the components or the
sunroof guide rail assembly.
Troubleshooting
Sunroof assembly removal
1. Remove the ceiling.
2. Disconnect and pull the connector of the sunroof ac-
tuator out.
3. Pull the four sunroof drainage pipes out (positions indi-
cated by the arrows in the diagram).
4. Remove the sunroof.
Remove the bolt and plastic gasket, and carry the sunroof
assembly out of car with the help of an assistant.
Sunroof assembly
Mounting bolt
Drive device
Plastic gasket
Drainage pipe port