2007 NISSAN TIIDA reverse

AV
NAVI CONTROL UNIT
AV-103
< ECU DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DTC IndexINFOID:0000000001728760
Self-diagnosis results display item
63
(W)Ground Ignition signal InputIgnition
switch
ON— Battery voltage
64
(V)Ground Parking brake signal InputIgnition
switch
ONParking brake ON 0 V
Parking brake OFF 12 V
65
(Y/G)Ground Reverse signal InputIgnition
switch
ONR position 12 V
Other than R position 0 V
66
(Y)GroundVehicle speed signal (8-
pulse) InputIgnition
switch
ONWhen vehicle speed is ap-
prox. 40 km/h (25MPH)
67
(Y)GroundCamera-connection recog-
nition signal InputIgnition
switch
ONConnected to camera con-
trol unit connector0 V
Not connected to camera
control unit connector5 V
69
(L)—AV communication signal
(H)Input/
Output—— —
70
(P)—AV communication signal
(L)Input/
Output—— —
71
(L)—CAN–HInput/
Output—— —
72
(P)—CAN–LInput/
Output—— —
73 Ground GPS antenna signal InputIgnition
switch
ACCNot connected to GPS an-
tenna connector5 V
74 — Shield — — — —Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIA6649J
DTC Error item Refer to
U1000 CAN COMM CIRCUIT [U1000]AV- 5 2 , "
DiagnosisProcedure"
U1010 CONTROL UNIT (CAN) [U1010] AV- 5 3 , "Diagnosis Procedure"
U1310 CONTROL UNIT (AV) [U1310]AV- 5 4 , "DTC Logic"
U1300
U1240
U1249
U124E
U124FAV COMM CIRCUIT [U1300]
SWITCH CONN [U1240]
AUDIO H/U CONN [U1249]
AMP CONN [U124E]
RDS CONN [U124F]AV- 7 9 , "
Description"
U1243 FRONT DISP CONN [U1243]AV- 7 6 , "Diagnosis Procedure"
U1244 GPS ANTENNA CONN [U1244]AV- 7 8 , "Diagnosis Procedure"
U1200 Control Unit FLASH-ROM [U1200]AV- 5 5 , "DTC Logic"
U1201 Gyro NO CONN [U1201]AV- 5 6 , "DTC Logic"

AV
MULTI AV SYSTEM SYMPTOMS
AV-109
< SYMPTOM DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO AUDIO
RELATED TO RGB IMAGE
RELATED TO VOICE ACTIVATED CONTROL
RELATED TO HANDS FREE PHONE
It cannot be switched to rear view
monitor.CONSULT-III self-diagnosis detects
a malfunction.Perform the self-diagnosis using CONSULT-III (MULTI
AV ) (AV- 4 8 , "CONSULT - III Function (MULTI AV)").
CONSULT-III self-diagnosis does not
detect a malfunction.NAVI control unit reverse signal circuit Symptoms Check items Possible malfunction location/Action to take
Symptom Check items Possible malfunction location / Action to take
Audio sound is not heard.No sound from all speakers Audio unit (XX-XX, "*****"
)
Sound is not heard only from the specif-
ic places (Front RH, rear RH, front LH
and rear LH).Sound signal circuit of suspect system
Symptoms Check items Possible malfunction location/Action to take
Color of RGB image is not proper.Light blue (Cyan) tintRGB signal (R: red) circuit (AV- 8 2 , "
Diagnosis Proce-
dure")
Purple (Magenta) tint and image is
rolling.RGB signal (G: green) circuit (AV- 8 3 , "
Diagnosis Proce-
dure")
Screen looks yellowish.RGB signal (B: blue) circuit (AV- 8 4 , "
Diagnosis Proce-
dure")
 RGB image is too dark.
 RGB image is too fuzzy.– RGB ground circuit
RGB image is not displayed.
(Nothing is displayed on the
screen.)“MULTI AV” is displayed on “SELECT
SYSTEM” screen of CONSULT-III.Perform the self-diagnosis using CONSULT-III (AV- 4 8 ,
"CONSULT - III Function (MULTI AV)").
“MULTI AV” is not displayed on “SE-
LECT SYSTEM” screen of CON-
SULT-III.NAVI control unit power supply and ground circuit (AV-
80, "NAVI CONTROL UNIT : Diagnosis Procedure")
Symptoms Check items Possible malfunction location/Action to take
The voice cannot be controlled
even if the voice control screen is
displayed.Voice sounds at “Speaker Test” and
“Voice Microphone Test” of “Confir-
mation / Adjustment Mode”.NAVI control unit (XX-XX, "*****"
)
Voice does not sound at “Speaker
Test” and “Voice Microphone Test” of
“Confirmation / Adjustment Mode”. MIC. power supply circuit (AV- 9 1 , "
Diagnosis Proce-
dure")
 Shield (MIC.) circuit (AV- 9 1 , "
Diagnosis Procedure")
 MIC. signal circuit (AV- 9 1 , "
Diagnosis Procedure")
The voice cannot be controlled.
(Voice control screen is not dis-
played.)TEL operation screen is displayed by
pressing and holding “ ” switch
of steering wheel switch.NAVI control unit (XX-XX, "*****"
)
 TEL operation screen is not dis-
played by pressing and holding
“ ” switch of steering wheel
switch.
 Other steering wheel switches are
normal.Steering switch (XX-XX, "*****"
)
“BACK”, “VOL UP”, “VOL DOWN”
and “ ” switches of steering
wheel switch are not operated.Steering switch signal B circuit XX-XX, "*****"
(XX-XX,
"*****")
All steering switches are not operat-
ed.Steering switch signal ground circuit (XX-XX, "*****"
)

AV
AV (NAVI) CONTROL UNIT
AV-121
< ON-VEHICLE REPAIR >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ON-VEHICLE REPAIR
AV (NAVI) CONTROL UNIT
Removal and InstallationINFOID:0000000001724701
AUDIO UNIT
Removal
1. Remove cluster lid C. Refer to IP-11, "Removal and Installation".
2. Remove the audio unit screws (A), disconnect the connectors
and remove the audio unit (1).
3. Remove the audio unit brackets.
Installation
Installation is in the reverse order of removal.
ALNIA0863ZZ

AV
GPS ANTENNA
AV-127
< ON-VEHICLE REPAIR >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
GPS ANTENNA
Removal and InstallationINFOID:0000000001724706
AUDIO UNIT
Removal
1. Remove cluster lid C. Refer to IP-11, "Removal and Installation".
2. Remove the GPS antenna screw (A), detach the GPS antenna
harness clip.
3. Remove the center console. Refer to IP-11, "
Removal and Installation".
4. Disconnect the GPS antenna connector (A) and remove the
GPS antenna.
Installation
Installation is in the reverse order of removal.
ALNIA0864ZZ
ALNIA0865ZZ

AV-128
< ON-VEHICLE REPAIR >[AUDIO WITH NAVIGATION]
DISPLAY UNIT
DISPLAY UNIT
Removal and InstallationINFOID:0000000001724707
AUDIO UNIT
Removal
1. Remove the AV (NAVI) control unit. Refer to AV-23, "Removal
and Installation".
2. Remove the AV (NAVI) control unit bracket screws (A), remove
the display unit screws (B), then remove the display unit brack-
ets (2) and remove the display unit (1).
Installation
Installation is in the reverse order of removal.
ALNIA0866ZZ

AV
MICROPHONE
AV-129
< ON-VEHICLE REPAIR >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
MICROPHONE
Removal and InstallationINFOID:0000000001724710
BLUETOOTH MICROPHONE
Removal
1. Remove over-head console assembly, roof finisher. Refer to INL-25, "Removal and Installation".
2. Remove the Bluetooth microphone Screw (A), then release the
Bluetooth microphone tabs and remove the Bluetooth micro-
phone (1).
Installation
Installation is in the reverse order of removal.
ALNIA0867ZZ

AV-130
< ON-VEHICLE REPAIR >[AUDIO WITH NAVIGATION]
NAVI CONTROL UNIT
NAVI CONTROL UNIT
Removal and InstallationINFOID:0000000001724711
NAVI CONTROL UNIT
Removal
CAUTION:
To avoid damage, eject map DVD-ROM before removing the NAVI control unit.
1. Disconnect the negative battery terminal.
2. Remove the front seat RH. Refer to SE-14, "
Removal and Installation".
3. Remove the NAVI control unit kick shield clips (A), then remove
the NAVI control unit kick shield (1).
4. Disconnect the NAVI control unit connectors (A) and the Blue-
tooth connector (B).
5. Remove the NAVI control unit bolts (C), then remove the NAVI
control unit (1).
6. Remove the NAVI control unit bracket screws and remove the
NAVI control unit brackets.
Installation
Installation is in the reverse order of removal.
ALNIA0873ZZ
ALNIA0874ZZ

BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
ACTIVE TEST
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)INFOID:0000000001451471
WORK SUPPORT
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function H/L SW POS [ON/OFF]
LIGHT SW 1ST [ON/OFF]
PASSING SW [ON/OFF]
AUTO LIGHT SW [ON/OFF]
FR FOG SW [ON/OFF]
RR FOG SW [ON/OFF]
DOOR SW-DR [ON/OFF] The switch status input from front door switch (driver side)
ENGINE STATUS The engine status received from ECM with CAN communication
LIT-SEN FAIL [OK/NOTOK] The sensor status received from light & rain sensor with serial link
 The serial link condition that BCM judges
AUT LIGHT SYS [ON/OFF] Auto light system status that BCM judges from the vehicle conditionMonitor item
[Unit]Description
Test item Operation Description
TAIL LAMPONTransmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF Stops the tail lamp request signal transmission.
HEAD LAMPHITransmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LOTransmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF Stops the high & low beam request signal transmission.
FR FOG LAMPONTransmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF Stops the front fog lights request signal transmission.
RR FOG LAMPON Outputs the voltage to turn the rear fog lamp ON.
 Transmits the rear fog lamp status signal to the combination meter with
CAN communication to turn the rear fog lamp indicator lamp ON.
OFF Stops the voltage to turn the rear fog lamp OFF.
 Stops the rear fog lamp status signal transmission.
DAYTIME RUNNING LIGHTONTransmits the day time running light request signal to IPDM E/R with
CAN communication to turn the each lamps ON.
OFF Stops the day time running light request signal transmission.
Work ItemSetting
ItemDescription
WIPER SPEED
SETTINGON
1With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFFWithout vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
RR WIP RVRS
SETON
2Change ON/OFF mode setting or rear wiper operation when gear is shifted to reverse
OFF