Page 505 of 5883
![NISSAN TIIDA 2007 Service Repair Manual CO-24
< ON-VEHICLE REPAIR >[HR16DE]
WATER OUTLET
WATER OUTLET
Exploded ViewINFOID:0000000001381574
Removal and InstallationINFOID:0000000001381575
REMOVAL
1. Drain engine coolant from radiator. Refer NISSAN TIIDA 2007 Service Repair Manual CO-24
< ON-VEHICLE REPAIR >[HR16DE]
WATER OUTLET
WATER OUTLET
Exploded ViewINFOID:0000000001381574
Removal and InstallationINFOID:0000000001381575
REMOVAL
1. Drain engine coolant from radiator. Refer](/manual-img/5/57395/w960_57395-504.png)
CO-24
< ON-VEHICLE REPAIR >[HR16DE]
WATER OUTLET
WATER OUTLET
Exploded ViewINFOID:0000000001381574
Removal and InstallationINFOID:0000000001381575
REMOVAL
1. Drain engine coolant from radiator. Refer to CO-11, "Changing Engine Coolant".
CAUTION:
Perform this step when engine is cold.
Never spill engine coolant on drive belt.
2. Disconnect radiator hose (upper). Refer to CO-16, "
Component".
3. Disconnect harness connector from engine coolant temperature sensor.
4. Remove electronic throttle control actuator water hoses (Northern Europe models).
5. Remove heater hoses.
6. Remove water outlet.
7. Remove engine coolant temperature sensor from water outlet, if necessary.
INSTALLATION
Installation is the reverse order of removal.
1. Engine coolant temperature sensor 2. Washer 3. Gasket
4. Radiator hose (upper) 5. Water outlet 6. Heater hose
7. Heater hose 8. Water hose (Northern Europe models) 9. Water hose (Northern Europe models)
A. To electronic throttle control actua-
torB. To heater core C. To radiator
: Engine front
PBIC3816E
Page 507 of 5883
CO-26
< DISASSEMBLY AND ASSEMBLY >[HR16DE]
COOLING FAN
DISASSEMBLY AND ASSEMBLY
COOLING FAN
DISASSEMBLY AND ASSEMBLYINFOID:0000000001534610
Disassembly
1. Remove cooling fan from fan motor.
2. Remove fan motor from fan shroud.
Inspection After Disassembly
Inspect cooling fan for crack or unusual bend.
If anything is found, replace cooling fan.
Assembly
Assembly is the reverse order of disassembly.
Page 522 of 5883
![NISSAN TIIDA 2007 Service Repair Manual RADIATOR
CO-41
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
N
P O
Perform this step when engine is cold.
Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to NISSAN TIIDA 2007 Service Repair Manual RADIATOR
CO-41
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
N
P O
Perform this step when engine is cold.
Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to](/manual-img/5/57395/w960_57395-521.png)
RADIATOR
CO-41
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
N
P O
Perform this step when engine is cold.
Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to EM-154, "
Component".
3. Remove reservoir tank as follows:
a. Disconnect reservoir tank hose.
b. Release the tab (A) in the direction shown by the arrow ( ).
c. Lift up while removing the reservoir tank hose, and remove it.
4. Disconnect harness connector from fan motors, and move harness to aside.
5. Remove radiator hoses (upper and lower).
6. Remove radiator core support cover.
7. Remove radiator core support (upper) bolts, bolts of stationary
part on the radiator core support side and clip. Lift radiator
assembly (1) from radiator (upper) mount part of radiator core
support (upper) (2).
8. Move radiator assembly (1) to the rearward direction of vehicle,
and then lift it upward to remove.
CAUTION:
Do not damage or scratch A/C condenser if equipped and
radiator core when removing.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Do not damage or scratch A/C condenser if equipped and radiator core when removing.
INSPECTION AFTER INSTALLATION
Check for leaks of engine coolant. Refer to CO-35, "Inspection".
Start and warm up engine. Visually check if there is no leaks of engine coolant.
PBIC3800E
PBIC3805E
Page 524 of 5883
COOLING FAN
CO-43
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
N
P O
Removal and InstallationINFOID:0000000001337846
REMOVAL
1. Drain engine coolant from radiator. Refer to CO-35, "Changing Engine Coolant".
CAUTION:
Perform this step when engine is cold.
Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to EM-154, "
Component".
3. Remove reservoir tank.
4. Disconnect radiator hose (upper) at radiator side. Refer to CO-40, "
Component".
5. Disconnect harness connectors from fan motor, and move harness to aside.
6. Remove cooling fan assembly.
CAUTION:
Be careful not to damage or scratch the radiator core.
INSTALLATION
Installation is the reverse order of removal.
Cooling fans are controlled by ECM. For details, refer to CO-28, "
Cooling Circuit".
CAUTION:
Be careful not to damage or scratch the radiator core.
Page 525 of 5883
![NISSAN TIIDA 2007 Service Repair Manual CO-44
< ON-VEHICLE REPAIR >[MR18DE]
WATER PUMP
WATER PUMP
ComponentINFOID:0000000001337848
Removal and InstallationINFOID:0000000001337849
REMOVAL
1. Drain engine coolant. Refer to CO-35, "Changing En NISSAN TIIDA 2007 Service Repair Manual CO-44
< ON-VEHICLE REPAIR >[MR18DE]
WATER PUMP
WATER PUMP
ComponentINFOID:0000000001337848
Removal and InstallationINFOID:0000000001337849
REMOVAL
1. Drain engine coolant. Refer to CO-35, "Changing En](/manual-img/5/57395/w960_57395-524.png)
CO-44
< ON-VEHICLE REPAIR >[MR18DE]
WATER PUMP
WATER PUMP
ComponentINFOID:0000000001337848
Removal and InstallationINFOID:0000000001337849
REMOVAL
1. Drain engine coolant. Refer to CO-35, "Changing Engine Coolant".
CAUTION:
Perform this step when the engine is cold.
2. Remove drive belt auto-tensioner. Refer to EM-153, "
Removal and Installation of Drive Belt Auto Ten-
sioner".
3. Remove water pump.
CAUTION:
Handle water pump vane so that it does not contact any other parts.
Water pump cannot be disassembled and should be replaced as a unit.
INSPECTION AFTER REMOVAL
Visually check that there is no significant dirt or rusting on water
pump body and vane (A).
Make sure that there is no looseness in vane shaft, and that it turns
smoothly when rotated by hand.
Replace water pump, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
Check for leaks of engine coolant. Refer to CO-35, "Inspection".
Start and warm up the engine. Visually check if there is no leaks of engine coolant.
1. Gasket 2. Water pump
PBIC3921E
PBIC3313J
Page 527 of 5883
![NISSAN TIIDA 2007 Service Repair Manual CO-46
< ON-VEHICLE REPAIR >[MR18DE]
THERMOSTAT
If out of the specification, replace thermostat.
INSTALLATION
Installation is in the reverse order of removal.
Thermostat
CAUTION:
Replace the rubber NISSAN TIIDA 2007 Service Repair Manual CO-46
< ON-VEHICLE REPAIR >[MR18DE]
THERMOSTAT
If out of the specification, replace thermostat.
INSTALLATION
Installation is in the reverse order of removal.
Thermostat
CAUTION:
Replace the rubber](/manual-img/5/57395/w960_57395-526.png)
CO-46
< ON-VEHICLE REPAIR >[MR18DE]
THERMOSTAT
If out of the specification, replace thermostat.
INSTALLATION
Installation is in the reverse order of removal.
Thermostat
CAUTION:
Replace the rubber ring with a new one.
Install thermostat while making rubber ring (1) groove fit to thermo-
stat flange (A) around the whole circumference.
Install thermostat (1) into the thermostat housing (2) with jiggle
valve (A) facing upwards.
Thermostat Housing
CAUTION:
Replace the rubber ring with a new one.
Securely insert the rubber ring into the mating groove of thermostat housing and install it.
Install the thermostat housing to the cylinder block without displacing the gasket from the gasket position.
INSPECTION AFTER INSTALLATION
Check for leaks of engine coolant. Refer to CO-35, "Inspection".
Start and warm up the engine. Visually check for engine coolant leaks.
ItemsThermostat
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Maximum valve lift 8 mm/ 95°C (0.315 in/ 203°F)
Valve closing temperature 77°C (171°F)
PBIC3315J
PBIC3548J
Page 529 of 5883
![NISSAN TIIDA 2007 Service Repair Manual CO-48
< ON-VEHICLE REPAIR >[MR18DE]
WATER OUTLET AND WATER CONTROL VALVE
Place a thread (A) so that it is caught in the valves of water control
valve (1). Immerse fully in a container (B) filled wit NISSAN TIIDA 2007 Service Repair Manual CO-48
< ON-VEHICLE REPAIR >[MR18DE]
WATER OUTLET AND WATER CONTROL VALVE
Place a thread (A) so that it is caught in the valves of water control
valve (1). Immerse fully in a container (B) filled wit](/manual-img/5/57395/w960_57395-528.png)
CO-48
< ON-VEHICLE REPAIR >[MR18DE]
WATER OUTLET AND WATER CONTROL VALVE
Place a thread (A) so that it is caught in the valves of water control
valve (1). Immerse fully in a container (B) filled with water. Heat
while stirring.
The valve opening temperature is the temperature at which the
valve opens and falls from the thread.
Continue heating. Check the full open valve lift amount.
NOTE:
The maximum valve lift amount standard temperature for water
control valve is the reference value.
After checking the maximum valve lift amount, lower the water
temperature and check the valve closing temperature.
If out of the specification, replace water control valve.
INSTALLATION
Installation is in the reverse order of removal.
Water Control Valve
CAUTION:
Replace the rubber ring with a new one.
Install water control valve while making rubber ring (1) groove fit to
water control valve flange (A) around the whole circumference.
While the mark (A) points to up, install water control valve (2) with
frame center (B) facing straight upward into water outlet (1).
Water Outlet
Install the water control valve to the cylinder head without displacing the valve from the valve position.
Water Hoses
Valve opening temperature 93.5 - 96.5°C (200 - 206°F)
Maximum valve lift 8 mm/ 108°C (0.315 in/ 226°F)
Valve closing temperature 90°C (194°F)
PBIC3314J
PBIC3317J
PBIC4700E
Page 531 of 5883
CO-50
< DISASSEMBLY AND ASSEMBLY >[MR18DE]
COOLING FAN
DISASSEMBLY AND ASSEMBLY
COOLING FAN
DISASSEMBLY AND ASSEMBLYINFOID:0000000001337847
Disassembly
1. Remove cooling fan from fan motor.
2. Remove fan motor from fan shroud.
Inspection After Disassembly
Inspect cooling fan for crack or unusual bend.
If anything is found, replace cooling fan.
Assembly
Assembly is the reverse order of disassembly.