2007 MITSUBISHI LANCER EVOLUTION transmission

MANUAL TRANSMISSION -Sensor, Switch and Relay or vehicles with ACD and AYC>22A-56
SENSOR, SWITCH AND RELAY VEHICLES WITH ACD AND AYC>
REMOVAL AND INSTALLATION
Caution
Before removing the steering wheel and air bag module assembly, be sure to refer to GROUP
52B Precautions in Servicing and Airbag Module Clock Spring.
1
3
2
4
5
Parking brake lever
Steering wheel sensor removal
steps
DSteering wheel and column cover
(Refer to GROUP 37A.)
1. Steering wheel sensor
G sensor removal steps
DFloor console (Refer to GROUP 52A.)
2. Longitudinal G sensor
3. Lateral G sensorElectric pump relay removal
4. Electric pump relay
ACD mode switch removal steps
DInstrument panel ornament (Refer to
GROUP 52A – Instrument Panel.)
5. ACD mode switch
NOTE
For details on the wheel speed sensor, refer to GROUP
35B.
REMOVAL SERVICE POINT
AA"STEERING WHEEL SENSOR REMOVAL
Remove the steering wheel sensor from the column switch.
Caution
Make sure no oil adheres to the steering wheel sensor
because a photocoupler is used.Steering wheel sensor

MANUAL TRANSMISSION -Sensor,SwitchandRelay vehicles with ACD and AYC>22A-57
INSPECTION
ELECTRIC PUMP RELAY CONTINUITY CHECK
1. Using a jumper wire, connect a battery (+) to terminal
13 of the electric pump relay and battery ( - ) to terminal
1.
2. While intermittently disconnecting the jumper wire at the
battery side, check for continuity between terminals 4
and 5 of the electric pump relay.
Jumper wireContinuity between No.4 - No.5
ConnectedContinuity
DisconnectedNo continuity
ACD MODE SWITCH CONTINUITY CHECK
ACD mode switch
terminalACD mode switchContinuity
No.1 - No.2ONContinuity
OFFNo continuity
No.3 - No.4-Continuity

22B-1
MANUAL
TRANSMISSION
OVERHAUL
CONTENTS
GENERAL DESCRIPTION 2...................
SPECIFICATIONS 6..........................
SERVICE SPECIFICATIONS 6.................
SEALANTS 7................................
LUBRICANTS 8..............................
SNAP RINGS, SPACERS AND THRUST
PLATES FOR ADJUSTMENT 9................
TIGHTENING TORQUE 11....................
SPECIAL TOOLS 12..........................
TRANSMISSION 15...........................
INPUT SHAFT 22............................OUTPUT SHAFT 29..........................
REVERSE IDLER GEAR 37...................
SPEEDOMETER GEAR 38....................
SELECT LEVER 39...........................
CONTROL HOUSING 40......................
CLUTCH HOUSING 43........................
TRANSMISSION CASE 46....................
CENTER DIFFERENTIAL 48..................
TRANSFER 51...............................

MANUAL TRANSMISSION OVERHAUL -General Description22B-2
GENERAL DESCRIPTION
SECTIONAL VIEW

MANUAL TRANSMISSION OVERHAUL -General Description22B-3
SECTIONAL VIEW

MANUAL TRANSMISSION OVERHAUL -General Description22B-4
SECTIONAL VIEW

MANUAL TRANSMISSION OVERHAUL -General Description22B-5
SECTIONAL VIEW
4>

MANUAL TRANSMISSION OVERHAUL -Specifications/Service Specifications22B-6
SPECIFICATIONS
TRANSMISSION MODEL TABLE
Transmission
modelGear ratioSpeedometer
gear ratioFinal
reduction
ratioFront LSDVehicle modelEngine model
W5M51 - 2 - X5BA28/364.529CT9A4G63 - I/C•T/C
W5M51 - 2 - X5B1B28/364.529Not providedCT9A4G63 - I/C •T/C
W5M51 - 2 - X5B2C28/364.529ProvidedCT9A4G63 - I/C •T/C
W5M51 - 2 - X5B3B28/364.529Not providedCT9A4G63 - I/C •T/C
W5M51 - 2 - X5B4C28/364.529ProvidedCT9A4G63 - I/C •T/C
GEAR RATIO TABLE
ABC
1st2.9282.785←
2nd1.950←←
3rd1.407←1.444
4th1.031←1.096
5th0.720←0.825
Reverse3.416←←
Transfer gear ratio0.3018←←
SERVICE SPECIFICATIONS
ItemsStandard value mmLimit value mm
Input shaft end play0.05 loose to 0.17 loose-
Input shaft front bearing end play0.01 tight to 0.12 loose-
Input shaft rear bearing end play0.01 tight to 0.12 loose-
Input shaft 5th speed gear end play0.01 tight to 0.09 loose-
Output shaft preload0.13 tight to 0.18 tight-
Output shaft bearing end play0.01 tight to 0.09 loose-
Output shaft 3rd speed gear end play0.01 tight to 0.09 loose-
Center differential case preload0.05 tight to 0.11 tight-
Center differential case pinion backlash0.025 - 0.150-
Clearance between synchronizer ring rear surface and gears-0.5
Provided