2007 MERCEDES-BENZ ML320CDI Comand Manual

528 Technical dataThe “Technical data” section provides the
necessary technical data for your vehicle.Parts service
All authorized Mercedes-Benz Centers
maintain a stock of Genuine
Mercedes-Benz parts required for mainte-
nance and repair work. In addition, strate-
gically located parts distribution centers
provide quick and reliable parts service.
More than 300 000 different parts for
Mercedes-Benz models are available.
Genuine Mercedes-Benz parts are subject-
ed to stringent quality inspections. Each
part has been specifically developed, man-
ufactured or selected for and adapted to
Mercedes-Benz vehicles.
Therefore, Genuine Mercedes-Benz parts
should be installed.
!
The use of non-genuine Mercedes-Benz
parts and accessories not authorized by
Mercedes-Benz could damage the vehicle, which
is not covered by the Mercedes-Benz Limited
Warranty, or could compromise the vehicle’s
durability or safety.

529 Technical data
Warranty coverage
Warranty coverage
Your vehicle is covered under the terms of
the warranties printed in the Service and
Warranty Information booklet. Your
authorized Mercedes-Benz Light Truck
Center will exchange or repair any defec-
tive parts originally installed on the vehicle
in accordance with the terms of the follow-
ing warranties:

New Vehicle Limited Warranty


Emission System Warranty


Emission Performance Warranty


California, Maine, Massachusetts, and
Vermont Emission Control Systems
WarrantyReplacement parts and accessories are
covered by the Mercedes-Benz Parts and
Accessories warranties, copies of which
are available at any authorized
Mercedes-Benz Light Truck Center.Loss of Service and Warranty
Information Booklet
Should you lose your Service and Warranty
Information booklet, have an authorized
Mercedes-Benz Light Truck Center arrange
for a replacement. It will be mailed to you.

530 Technical dataIdentification labels1Certification label (on driver’s B-pillar)
The V
ehicle I
dentification N
umber (VIN)
can be found in the following locations:


on the certification label


embossed underneath the
passenger-side rear seat (
page 531)


on the lower edge of the windshield
(page 531)
Example certification label (U.S. vehicles)2Paintwork code
3VIN
Example certification label
(Canada vehicles)2Paintwork code
3VINi
Data shown on certification label are for
illustration purpose only. These data are specific
to each vehicle and may vary from data shown in
the illustration. Refer to certification label on
vehicle for actual data specific to your vehicle.

531 Technical data
Identification labels
4Seat cushion
5Floor cover
6VIN
Fold the seat cushion4 forward
(page 285).

Fold floor cover5 in direction of the
arrow.
The VIN6 is now visible.7Emission control information label,
includes both federal and California
certification exhaust emission
standards
8Engine number (engraved on engine)
9Vacuum line routing diagram label
aVIN (lower edge of windshield)
i
When ordering parts, please specify vehicle
identification and engine numbers.

532 Technical dataLayout of poly-V-belt driveML 350
1Idler pulley
2Idler pulley
3Automatic belt tensioner
4Power steering pump
5Air conditioning compressor
6Crankshaft
7Coolant pump
8Generator (alternator)
ML 320 CDI
1Coolant pump
2Idler pulley
3Automatic belt tensioner
4Power steering pump
5Air conditioning compressor
6Crankshaft
7Idler pulley
8Generator (alternator)
ML 500
1Automatic belt tensioner
2Power steering pump
3Air conditioning compressor
4Crankshaft
5Coolant pump
6Generator (alternator)
7Idler pulley

533 Technical data
Layout of poly-V-belt drive
ML 63 AMG
1Idler pulley
2Idler pulley
3Idler pulley
4Automatic belt tensioner
5Power steering pump
6Air conditioning compressor
7Crankshaft
8Coolant pump
9Generator (alternator)

534 Technical dataEngineModel
ML 320 CDI (164.122
1)
1The quoted data apply only to the standard vehicle. See an authorized Mercedes-Benz Light Truck Center for the corresponding data of all special bodies and
special equipment.
ML 350 (164.186
1)
Engine
642
272
Mode of operation
Diesel 4-stroke engine
4-stroke engine, gasoline injection
No. of cylinders
6
6
Bore
3.27 in (83.00 mm)
3.66 in (92.90 mm)
Stroke
3.62 in (92.00 mm)
3.38 in (86.00 mm)
Total piston displacement
182 cu in (2987 cm
3)
213 cu in (3498 cm
3)
Compression ratio
16.5:1
10.7:1
Output acc. to SAE J 1349
221 hp/3800 rpm
(165 kW/3800 rpm)
268 hp/6000 rpm
2
(200 kW/6000 rpm)
2Premium fuel required. Performance may vary with fuel octane rating.Maximum torque acc. to SAE J 1349
398 lb-ft/1600-2400 rpm
(540 Nm/1600-2400 rpm)
258 lb-ft/2400-5000 rpm
(350 Nm/2400-5000 rpm)
Maximum engine speed
4500 rpm
6500 rpm
Firing order
1-4-2-5-3-6
1-4-3-6-2-5
Poly-V-belt
2 035 mm
2 404 mm

535 Technical data
Engine
Model
ML 500 (164.175
1)
1The quoted data apply only to the standard vehicle. See an authorized Mercedes-Benz Light Truck Center for the corresponding data of all special bodies and special
equipment.
ML 63 AMG (164.177
1)
Engine
113
156
Mode of operation
4-stroke engine, gasoline injection
4-stroke engine, gasoline injection
No. of cylinders
8
8
Bore
3.82 in (97.00 mm)
4.02 in (102.20 mm)
Stroke
3.31 in (84.00 mm)
3.72 in (94.60 mm)
Total piston displacement
303 cu in (4966 cm
3)
378.8 cu in (6208 cm
3)
Compression ratio
10:1
11.3:1
Output acc. to SAE J 1349
302 hp/5600 rpm
2
(225 kW/5600 rpm)
2Premium fuel required. Performance may vary with fuel octane rating.
503 hp/6800 rpm
2
(375 kW/6800 rpm)
Maximum torque acc. to SAE J 1349
339 lb-ft/2700-4750 rpm
(460 Nm/2700-4750 rpm)
465 lb-ft/5200 rpm
(630 Nm/5200 rpm)
Maximum engine speed
6300 rpm
7200 rpm
Firing order
1-5-4-2-6-3-7-8
1-5-4-2-6-3-7-8
Poly-V-belt
2 370 mm
2 369 mm