2007 MERCEDES-BENZ ML320CDI Comand Manual

280 Controls in detailDriving systemsThe rear view camera is an optical parking
aid. It shows you the area behind the vehi-
cle in the COMAND system display when
reverse gearR is engaged, for example
during parallel parking.
The rear view camera is located near the
tailgate handle.
1Rear view cameraSwitching the rear view camera on and
off

Switch on the ignition (
page 40).

Shift the automatic transmission in
positionR (
page 187).
The area behind the vehicle appears in
the COMAND system display.

Shift the automatic transmission
intoP,N orD to switch off the rear
view camera.
i
The area behind the vehicle is shown in the
COMAND system display as a mirror image, like
in the rear view mirror.
i
The image from the rear view camera will no
longer be displayed if you select another
function on the COMAND system while reverse
gearR is engaged. To display the image again,
disengage and reengage reverse gearR.

281 Controls in detail
Loading
Loading
Carriers*
Roof railsFor further information, contact your
authorized Mercedes-Benz Light Truck
Center.
Loading instructions
Warning!
G
Only use carriers* when the basic carrier
bars* have been completely mounted. The
left and right roof rails are only stabilized by
means of the basic carrier bars* mounted.
Follow the manufacturer’s installation
instructions. Otherwise, an improperly at-
tached carrier system or its load could be-
come detached from the vehicle.
Do not exceed the maximum roof load of
220 lb (100 kg).
Take into consideration that when the roof is
loaded, the handling characteristics are dif-
ferent from those when operating the vehi-
cles without a roof loaded.
!
Load the carriers* in such a way that the
vehicle cannot be damaged while driving.
Make sure


the tailgate can be completely opened


the tilt/sliding sunroof can be completely
raised at the rear
Warning!
G
Always fasten items being carried as secure-
ly as possible using cargo tie-down rings and
fastening materials appropriate for the
weight and size of the load.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and can cause in-
jury to vehicle occupants unless the items
are securely fastened in the vehicle.
To help avoid personal injury during a colli-
sion or sudden maneuver, always use tie
down rings, and if so equipped, always use
partition net* when transporting cargo.
Never drive vehicle with the tailgate open.
Deadly carbon monoxide (CO) gases may
enter vehicle interior resulting in uncon-
sciousness and death.

282 Controls in detailLoadingLoad distributionThe gross vehicle weight which is the
weight of the vehicle including fuel, tools,
spare wheel, installed accessories, pas-
sengers and luggage/cargo must never
exceed the load limit and Gross Vehicle
Weight Rating (GVWR) for your vehicle as
specified on the placard located on the
driver’s door B-pillar (
page 530). In addi-
tion, the load must be distributed in such a
way so that the weight on each axle never
exceeds the Gross Axle Weight Rating
(GAWR) for the front and rear axle. The
GVWR and GAWR for your vehicle are indi-cated on the certification label which can
be found on the driver’s door B-pillar
(
page 530).
For more information, see “Tire and Load-
ing Information” (
page 369).
The handling characteristics of a fully load-
ed vehicle depend greatly on the load dis-
tribution. It is therefore recommended to
load the vehicle according to the illustra-
tions shown, with the heaviest items being
placed towards the front of the vehicle.
Please pay attention to and comply with
the following instructions when loading the
vehicle and transporting cargo:


Always place items being carried
against front or rear seat backrests,
and fasten them as securely as possi-
ble.


The heaviest portion of the cargo
should always be kept as low as possi-
ble against front or rear seat backrests.For additional safety when transporting
cargo while the rear seats are unoccupied,
fasten the outer seat belts crosswise into
the opposite side buckles.
i
The cargo compartment is the preferred
place to carry objects. The expanded cargo com-
partment (
page 284) should only be used for
items which do not fit in the cargo compartment
alone.

283 Controls in detail
Loading
Cargo tie-down rings
Your vehicle is equipped with six cargo
tie-down rings.
Carefully secure cargo by applying even
load on all rings with rope of sufficient
strength to hold down the cargo.Cargo compartment
Four cargo tie-down rings are located in
the cargo compartment.
1Cargo tie-down ringBehind front seats
Two cargo tie-down rings are located in the
footwell behind the driver’s and passenger
seat.
1Cargo tie-down ringi
While the partition net* (
page 287) will
help protect you from smaller objects, it cannot
prevent the movement of large, heavier objects
into the passenger compartment in an accident,
during hard braking or sudden maneuvers. Such
items must be properly secured using the cargo
tie-down rings in the cargo compartment floor.

284 Controls in detailLoadingHooks
Four hooks are located on the rear com-
partment trim panels, two on each side.
1Hook
Use the hooks to secure light weight items
only. The maximum permissible weight per
hook is 9 lbs (4 kg).
Expanding cargo compartment
You can separately fold the left and right
rear seat backrests to expand the cargo
compartment.
Folding the rear seat backrest forwardWarning!
G
When expanding the cargo compartment,
always fully fold the corresponding seats
and, if so equipped, always use the partition
net* (
page 287) when transporting cargo.
Unless you are transporting cargo, the back-
rests must remain properly locked in the up-
right position.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and can cause
injury to vehicle occupants unless the items
are securely fastened in the vehicle.
Always use the cargo tie down rings
(
page 283).
Warning!
G
Never drive the vehicle with the tailgate
open. Deadly carbon monoxide (CO) gases
may enter vehicle interior resulting in un-
consciousness and death.!
Always release the seat cushion and fold it
up before folding the seat backrest forward. The
covering on the seat backrest may otherwise be
damaged.
When the seat backrest are folded forward, the
front seats may not be moved to the rearmost
position. Otherwise you could damage the front
and second-row seats.

285 Controls in detail
Loading
1Release handle
2Seat cushion
Pull release handle1.

Fold seat cushion2 forward.3Release handle
4Seat backrest

Make sure the rear seat head restraints
are in the lowermost position
(page 128).

Pull release handle3.A red indicator5 will be visible and the
seat backrest4 is released.
5Indicator

Fold seat backrest4 forward.

286 Controls in detailLoadingReturning the rear seat backrest to
original position
1Seat backrest
2Seat cushion
Fold seat backrest1 rearward until it
engages.
The red indicator5 (
page 285)
should no longer be visible.

Fold seat cushion2 rearward until it
locks into position.

Check for secure locking by pushing
and pulling on the seat backrest.
Cargo compartment cover blind
The cargo compartment cover blind can be
installed behind the rear seats.1Handle
2Mount
Rolling out blind

Pull blind on handle1 across the car-
go compartment.

Guide blind into mounts2 and re-
lease.
Rolling up blind

Disengage blind and guide retraction
by its handle1.
Warning!
G
If a red indicator is visible with the backrest
up, then the backrest is not properly locked
into position.
Always lock backrest in its upright position
when the rear seats are occupied, or the ex-
tended cargo compartment is not in use.
Check for secure locking by pushing and
pulling on the backrest.!
With the cargo compartment cover blind in-
stalled, do not pile luggage higher than the lower
edges of the rear side windows.

287 Controls in detail
Loading
Removing blind
1Release button
2Blind
Roll the blind up (
page 286).

Push release button1.

Pull blind2 to the left against the
spring pressure until the spring in the
cover audibly engages.

Remove the blind.
Installing blind

Place left side of blind2 in left mount.

Position right side of blind2 over right
mount.

Press release button1 and guide
cover2 into mount.

Make sure the cargo compartment
cover blind is securely fastened.
Partition net*
i
Before removing cargo compartment cover
blind behind the rear seats, fold the left or right
rear seat forward. Afterwards, return the left or
right rear seat into its original position.
i
Before installing cargo compartment cover
blind behind the front seats, fold the rear seats
forward.
Warning!
G
Make sure the partition net is properly en-
gaged at top and bottom position and the
tightening belts are securely fastened.
Never use a damaged partition net.
To help avoid personal injury from smaller
objects being thrown around in the occu-
pant compartment during a collision or sud-
den maneuver, always use partition net
when transporting cargo.
The partition net cannot prevent the move-
ment of large, heavier objects into the pas-
senger compartment in an accident. Such
items must be properly secured using the
cargo tie-down rings (
page 283) in the
cargo compartment floor.
Passenger use of seats behind installed par-
tition net is restricted because of the foot-
well being taken up by the net.