2007 ISUZU KB P190 torque

6A-22 ENGINE MECHANICAL (4JK1/4JJ1)
Torque Specifications



RTW 56ALF003801


Special Tools
ILLUSTRATION PART NO.
PART NAME

5-8840-2823-0
Engine hanger



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-26 ENGINE MECHANICAL (4JK1/4JJ1)





RTW 56ASH022701
Legend
1. 3.0 - 5.0 mm (0.118 - 0.197 in)
2. 3.0 - 5.0 mm (0.118 - 0.197 in)

3. Install the cylinder head cover.
Tightening torque: 10 N ⋅
⋅⋅
⋅
m (1.0 kg ⋅
⋅⋅
⋅
m / 87 lb in)
• Tighten the nut and bolts in order shown in the
illustration.







RTW 56ASH004801
4. Install the blow-by hose.
5. Install the leak-off hose and the fuel injecto
r
connector.
6. Install the harness bracket to the cylinder head cover.
7. Install the intercooler (High output). • Install the intercooler.
• Install the two intake hoses.
• Connect the BARO sensor harness connector.


8. Install the intake air duct.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb in)
9. Install the engine cover.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-31
Installation
1. Install the intake manifold gasket.
2. Install the intake manifold. • Tighten the nuts and bolts in the orde
r
described in the drawing.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)







RTW 56ASH018001
3. Install the throttle assembly and gasket.
• Tighten the bolts to the specified torque.
Tightening torque: 10 N ⋅
⋅⋅
⋅
m (1.0 kg ⋅
⋅⋅
⋅
m / 87 lb in)
4. Install the vacuum hose of swirl control valve.
5. Install the injection pipe (fuel rail - fuel injector). • It installs sequentially from No. 4 cylinder.
Tightening torque: 29 N ⋅
⋅⋅
⋅
m (3.0 kg ⋅
⋅⋅
⋅
m / 22 lb ft)
6. Install the EGR valve. • Tighten the nuts to the specified torque.
Tightening torque: 27 N ⋅
⋅⋅
⋅
m (2.8 kg ⋅
⋅⋅
⋅
m / 20 lb ft)
7. Install the engine oil level guide tube.
Tighten the nuts to the specified torque.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
8. Install the intercooler (High output).
9. Connect the connector of other parts. • Fuel Injector
• Throttle Assembly
• EGR Valve
• Glow Plug
• Barometric Sensor
• A/C Compressor Connector
10. Install the leak-off hose.




RTW 56ASH024301
Legend
1. Injector Leek-off Hose

11. Install the intake air duct.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
12.Install the A/C compressor bracket. Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
13.Install the A/C compressor and A/C compresso
r
connector.
Tightening torque: 44 N ⋅
⋅⋅
⋅
m (4.5 kg ⋅
⋅⋅
⋅
m / 33 lb ft)
14.Install the A/C belt.
Check the A/C belt tension.
Depress the A/C belt mid-portion with 98 N (10 kg
/
22 lb) force.
Standard deflection: 7.6 - 9.2 mm (0.29 - 0.36 in)



RTW 510SH000201
15. Install the engine cover.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-32 ENGINE MECHANICAL (4JK1/4JJ1)
Torque Specifications




RTW 76AMF000101


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-37
Waste gate operation
1. Remove the hose from the waste gate actuator.
2. Install the pressure gauge (general tool). Refer to the illustration.





RTW 56ASH005701
Legend
1. W aste Gate Actuator
2. W aste Gate Hose
3. Pressure Gauge (General Tool)

3. Use the pressure gauge pump to apply pressure
(load) to the waste gate actuator (the engine must
be off).
4. Note the pressure at which the control rod moves 2 mm (0.078 in). This pressure must be within the
specified limit.

Control rod pressure range: kPa (mmHg / psi)
109 − 118 (818 − 885 / 16 − 17)

5. Inspect the hose for cracks and other damage.
Replace the hose if necessary.
6. Do not apply a pressure of more than 120 kPa (900 mmHg) to the waste gate actuator.

Installation
1. Put the gasket in to install the exhaust manifold.
• Tighten up with the 8 nuts according to the
order given in the figure.
Tightening torque: 52 N ⋅
⋅⋅
⋅
m (5.3 kg ⋅
⋅⋅
⋅
m / 38 lb ft)
Note:
Do not tighten up too much because it hampers
expansion and contraction due to the heat from the
manifold.









RTW 56ASH005801
2. Install the gasket and turbocharger to the exhaust
manifold. Tighten the nuts to the specified torque.
Tightening torque: 27 N ⋅
⋅⋅
⋅
m (2.8 kg ⋅
⋅⋅
⋅
m / 20 lb ft)




RTW 56ASH005501
Legend
1. Exhaust Manifold
2. Gasket
3. Turbocharger


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-38 ENGINE MECHANICAL (4JK1/4JJ1)
3. Install the catalyst converter.
Tighten the nuts to the specified torque.
Tightening torque: 27 N ⋅
⋅⋅
⋅
m (2.8 kg ⋅
⋅⋅
⋅
m / 20 lb ft)
4. Connect the front propeller shaft flange (Front Dif
f
Side, 4 ×4 only).
5. Install the front exhaust pipe.
Tighten the nuts to the specified torque.
Tightening torque
Exhaust Manifold Side: 67 N⋅
⋅⋅
⋅m (6.8 kg⋅
⋅⋅
⋅m / 49 lb ft)
Exhaust Pipe Side: 43 N
⋅
⋅⋅
⋅m (4.4 kg⋅
⋅⋅
⋅m / 32lb ft)
6. Install the water feed pipe to the turbocharger (1).
• Tighten the joint bolts to the specified torque.
Tightening torque: 54 N ⋅
⋅⋅
⋅
m (5.5 kg ⋅
⋅⋅
⋅
m / 40 lb ft)
• Install the pipe bracket and tighten the bolts to
the specified torque.
Tightening torque: 10 N ⋅
⋅⋅
⋅
m (1.0 kg ⋅
⋅⋅
⋅
m / 87 lb in)
• Install the rubber hose between the wate
r
return pipe and the thermostat housing.







RTW 56ASH019101
7. Install the water return pipe. Tighten the joint bolt
to the specified torque.
Tightening torque: 54 N ⋅
⋅⋅
⋅
m (5.5 kg ⋅
⋅⋅
⋅
m / 40 lb ft)









RTW 56ASH019001
8. Install the turbocharger oil feed pipe to the top of
the turbocharger. Tighten the joint bolts to the
specified torque.
Tightening torque (Turbo charger side): 23 N ⋅
⋅⋅
⋅
m (2.3 kg ⋅
⋅⋅
⋅
m / 17 lb ft)
Tightening torque (Oil cooler side): 23 N ⋅
⋅⋅
⋅
m (2.3 kg ⋅
⋅⋅
⋅
m / 17 lb ft)
• Install the pipe bracket and tighten the bolts to
the specified torque.
Tightening torque: (Clip) 10 N ⋅
⋅⋅
⋅
m (1.0 kg ⋅
⋅⋅
⋅
m / 87 lb in)



RTW 56ASH00610
Legend
1. Oil Feed Pipe
2. Clip
3. Oil Return Pipe




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-39
9. Tighten the oil return pipe bolts and nuts to the
specified torque.
Tightening torque (Turbocharger side): 10 N ⋅
⋅⋅
⋅
m (1.0 kg ⋅
⋅⋅
⋅
m / 87 lb in)
Tightening torque (Crank case side): 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
10.Install the EGR cooler. • Refer to “EGR Cooler” in EXHAUST SYSTEM
section.
11. Install the heat protector. • Refer to “EGR Cooler” in EXHAUST SYSTEM
section.
12. Install the intake hose between the intercooler and the intake throttle (7).
13. Install the intake hose between the turbocharge
r
and the intercooler (9).
14. Install the intake duct between the turbocharge
r
and the air cleaner (8).
Tightening torque: 6 N ⋅
⋅⋅
⋅
m (0.6 kg ⋅
⋅⋅
⋅
m / 52 lb in)
15.Replenish the coolant.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-40 ENGINE MECHANICAL (4JK1/4JJ1)
Torque Specifications



RTW 76ALF000901


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007