2007 ISUZU KB P190 EGR

ENGINE CONTROL SYSTEM (4JK1/4JJ1) 6E-7
P1261 34 CAAInjector Positive Voltage Control Circuit (Supply Voltage
High)
P1262 34 A AA Injector Positive Voltage Control Circuit Group 2
P1404 45 A AA EGR Position Fault (Closed Position Error)
P1404 45 A -- EGR Position Fault (Learned Position Error)
P1411 445 A AA EGR Solenoid Control Driver
P1412 445 A AA EGR Solenoid Control Driver
P1413 445 A AA EGR Solenoid Control Driver
P156A 135 C AA Battery Voltage Low
P156B 135 C AA Battery Voltage High
P161B 179 C AA Immobilizer Wrong Response
P1621 54 C AAControl Module Long Term Memory Performance
(Learned Data)
P1621 254 C AAControl Module Long Term Memory Performance (VIN or
Immobilizer Data)
P1664 76 D -- Service Vehicle Soon Lamp Control Circuit (Low Voltage)
P1664 76 C --Service Vehicle Soon Lamp Control Circuit (High
Voltage)
P2100 446 B AA Intake Throttle Solenoid Circuit Open
P2101 446 B AA Intake Throttle Solenoid Circuit Low
P2103 446 B AA Intake Throttle Solenoid Circuit High
P2122 121 C AA Pedal Position Sensor 1 Circuit Low Input
P2123 121 C AA Pedal Position Sensor 1 Circuit High Input
P2127 122 C AA Pedal Position Sensor 2 Circuit Low Input
P2128 122 C AA Pedal Position Sensor 2 Circuit High Input
P2132 123 C AA Pedal Position Sensor 3 Circuit Low Input
P2133 123 A AA Pedal Position Sensor 3 Circuit High Input
P2138 124 C AA Pedal Position Sensor 1 - 2 Voltage Correlation
P2139 125 C AA Pedal Position Sensor 1 - 3 Voltage Correlation
P2140 126 C AA Pedal Position Sensor 2 - 3 Voltage Correlation
P2146 158 A AA Fuel Injector Group 1 Supply Voltage Circuit Short
P2147 158 A AA Fuel Injector Group 1 Supply Voltage Circuit Low
P2148 158 A AA Fuel Injector Group 1 Supply Voltage Circuit High
P2149 159 A AA Fuel Injector Group 2 Supply Voltage Circuit Short
P2150 159 A AA Fuel Injector Group 2 Supply Voltage Circuit Low
P2151 159 A AA Fuel Injector Group 2 Supply Voltage Circuit High
P2227 71 A A- Barometric Pressure Sensor Circuit Range/ Performance
P2228 71 A AA Barometric Pressure Sensor Circuit Low
P2229 71 A AA Barometric Pressure sensor Circuit High
P2621 94 - -A Throttle Position Output Circuit Low
DTC
Flash
Code DTC Type
DTC Descriptor
Euro 4
Specification Except Euro 4
Specification
(High Output) Except Euro 4
Specification (Standard Output)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6E-22 ENGINE CONTROL SYSTEM (4JK1/4JJ1)
MAF & IAT Sensors, Intake Throttle and EGR Valves
RTW76EXF001501
Intake
throttle
position
sensor
Intake
throttle
solenoid 6
35 3
0.5
WHT
0.5
ORN
0.5
GRY
0.5
BLU E-38
56 1
0.5
RED E-71
E-90
63 6
0.5
YEL
36
57
55
5
2 5V reference 3
5V reference
ECM
ECM
Control
low
side
(PWM) Control
low
side
(PWM) 30
5V reference 2
0.5
WHT/
BLU
31
0.5
GRY
0.5
RED
0.5
BRN
EGR
solenoid EGR
position
sensor
32
62 E-90
43 1
2
Low
reference Low
reference
Low
reference
Low
reference
Shield
ground 41
0.5
BLU/
RED
0.5
BLU/
GRN
0.5
BLK 0.5
WHT/
BLU MAF
sensor Signal
Signal
Signal
Signal
40
0.5
RED/
BLU 0.5
ORN/
BLU
4
3
1 E-47
5
61
43
42 2
E-47IAT
sensor
14
0.5
RED/
BLU
H-4
EB-4
Engine
10A Fuse/
relay
box
(Engine
room)
E-38E-71
Turbocharger
nozzle
control
solenoid
Swirl
control
solenoid +B
+B

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6E-28 ENGINE CONTROL SYSTEM (4JK1/4JJ1)
Legend1. Boost pressure sensor
2. Turbocharger nozzle control solenoid
3. Barometric pressure (BARO) sensor (High output)

Legend
1. Exhaust gas recirculation (EGR) valve
2. Intake throttle valve

Legend
1. Engine control module (ECM)
2. Mass air flow (MAF) sensor / intake air templature
(IAT) sensor

Legend
1. Fuel rail pressure (FRP) sensor
2. Pressure limiter valve
3. Fuel rail

RTW76ESH003501
1
23
RTW56ESH002601
1
2
RTW56ESH003101
1
2
RTW76ESH002101123

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE CONTROL SYSTEM (4JK1/4JJ1) 6E-31
Engine Control Module (ECM) Connector
End Views
Engine Control Module (ECM)-J1
Connector No. E-90
Connector Color Gray
Test Adapter No. J-35616-64A
Pin No. Wire Color Pin Function
1 — Not used
2 — Not used
3 — Not used
4 — Not used
5 — Not used
6 — Not used
7 — Not used
8 — Not used
9 — Not used
10 — Not used
11 — Not used
12 — Not used
13 — Not used
14 — Not used
15 — Not used
16 — Not used
17 ORN BARO sensor low reference
18 PNK/ GRN BARO sensor signal
19 BLU/ GRN BARO sensor 5V reference
20 GRN Boost pressure sensor 5V
reference
21 YEL Boost pressure sensor signal
RTW76ESH003101
12345678910111213141516
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
Pin No. Wire Color
Pin Function
22 BLK Boost pressure sensor shield
ground
23 BLU Boost pressure sensor low
reference
24 YEL Cylinder #2 fuel injector control
25 BRN Cylinder #3 fuel injector control
26 WHT ECT sensor low reference
27 GRN/ RED ECT sensor signal
28 YEL/ RED FT sensor low reference
29 PNK FT sensor signal
30 RED EGR position sensor low
reference
31 WHT/ BLU EGR position sensor 5V reference
32 GRY EGR position sensor signal
33 BLU/ YEL Cylinder #1 fuel injector control
34 BLU/ YEL FRP regulator control high side
35 BLU Intake throttle position sensor low
reference
36 GRY Intake throttle position sensor 5V
reference
37 GRN CKP sensor 5V reference
38 BLK CKP sensor shield ground
39 BLU CKP sensor low reference
40 ORN/ BLU MAF sensor signal
41 BLU/ RED IAT sensor signal
42 BLK MAF sensor shield ground
43 WHT/ BLU MAF sensor low reference
44 BLK CMP sensor low reference
45 WHT CMP sensor signal
46 RED CMP sensor 5V reference
47 RED FRP sensor 5V reference
48 WHT FRP sensor signal
49 BLK FRP sensor shield ground
50 BLU/ RED FRP regulator low side
51 WHT Cylinder #3 fuel injector charge
voltage
52 BLU Cylinder #1 fuel injector charge
voltage
53 GRN Cylinder #4 fuel injector control
54 BLK/ YEL FRP regulator control high side
55 WHT Intake throttle drive voltage
56 RED Intake throttle control low side
57 ORN Intake throttle position sensor
signal

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6E-32 ENGINE CONTROL SYSTEM (4JK1/4JJ1)
Engine Control Module (ECM)-J2
Pin No. Wire ColorPin Function
58 YEL CKP sensor signal
59 PNK Fuel filter switch signal
60 — Not used
61 BLU/ GRN IAT sensor low reference
62 BRN EGR drive voltage
63 YEL EGR control low side
64 BLK CMP sensor shield ground
65 — Not used
66 ORN/ BLK Turbocharger nozzle control
solenoid valve control
67 YEL Swirl control solenoid valve
control
68 WHT FRP sensor signal
69 BLK FRP sensor low reference
70 BLU/ RED FRP regulator low side
71 RED Cylinder #2 fuel injector charge
voltage
72 PNK Cylinder #4 fuel injector charge
voltage
73 BLK Ground
Connector No. C-58
Connector Color Black
Test Adapter No. J-35616-64A
Pin No. Wire Color Pin Function
1 ORN Brake switch 2 signal
2 BLK/ GRN Diagnostic request switch
RTW76ESH003101
12345678910111213141516
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
Pin No. Wire Color
Pin Function
3 RED/ GRN P or N range switch (A/T)
BLK/ WHT Neutral switch (M/T)
4 GRN/ BLK Thermo relay signal
5 — Not used
6 — Not used
7 BLU APP sensor 3 5V reference
8 BL/ UWHT APP sensor 3 signal
9 ORN APP sensor 2 5V reference
10 BLU/ GRN APP sensor 2 signal 11 WHT APP sensor 1 5V reference
12 RED APP sensor 1 signal
13 GRY/ GRN Cruise cancel switch signal
14 WHT/ GRN Cruise main switch signal
15 — Not used
16 — Not used
17 — Not used
18 — Not used
19 YEL Clutch switch signal
20 — Not used
21 RED Brake switch 1 signal
22 — Not used
23 BLU/ RED APP sensor 3 low reference
24 BLK APP sensor 3 shield ground
25 ORN/ BLU APP sensor 2 low reference
26 BLK APP sensor 2 shield ground
27 BLK APP sensor 1 low reference
28 BLK APP sensor 1 shield ground
29 BRN/ YEL Cruise resume switch signal
30 LT GRN Cruise set switch signal
31 — Not used
32 — Not used
33 BLK/ RED Engine speed signal output
34 — Not used
35 ORN/ BLU Starter cut relay control
36 — Not used
37 BLK/ BLU Glow relay control
38 — Not used
39 — Not used
40 — Not used
41 — Not used
42 — Not used

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE CONTROL SYSTEM (4JK1/4JJ1) 6E-37
EGR ValveEngine Coolant Temperature (ECT) Sensor
Connector No.
B-58
Connector Color Black
Test Adapter No. J-35616-2A
Pin No. Wire Color Pin Function
1 BKL/ GRN Diagnostic request switch (ECM)
2 — Not used
3 — Not used
4 BLK Ground
5 BLK Ground
6 BLU CAN high
7 VIO/ GRN Keyword serial data (TCM
[standard output], EHCU [ABS
module] and SRS control unit)
8 — Not used
9 — Not used
10 — Not used 11 YEL/ BLK Diagnostic request switch (TCM)
12 ORN/ WHT Diagnostic request switch (EHCU
[ABS module])
13 RED Diagnostic request switch (SRS
control unit)
14 YEL CAN low
15 — Not used
16 RED/ YEL Battery voltage
LNW46ESH001901
1
4 2
5 3
6
Connector No. E-71
Connector Color Gray
Test Adapter No. J-35616-64A
Pin No. Wire Color Pin Function
1 WHT/ BLU Position sensor 5V reference
2 RED Position sensor low reference
3 GRY Position sensor signal
4 BRN Solenoid drive voltage
5—Not used
6 YEL Solenoid control low side (PWM)
Connector No. E-41
Connector Color Gray
Test Adapter No. J-35616-64A
Pin No. Wire Color Pin Function
1 GRN/ RED Sensor signal
2 WHT Sensor low reference
3 YEL/ BLK Gauge signal
LNW46ESH001701
12
3

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6E-48 ENGINE CONTROL SYSTEM (4JK1/4JJ1)
Fuel Rail Pressure SensorVolts1.4 to 1.5 volts More than 2.1 volts (4JJ1 Euro 4
specification)
More than 1.8 volts (4JJ1 except Euro 4 specification)
More than 1.9 volts (4JK1)
FRP Regulator Command (Fuel Rail Pressure) %
35 to 50 % 35 to 45 %
FRP Regulator Commanded Fuel Flow mm
3/sec More than 1,000 mm3/sec More than 2,000 mm3/sec
FRP Regulator Feedback (Fuel Rail Pressure) mA
1,600 to 2,000 mA 1,500 to 1,800 mA
Accelerator Pedal Position %0% 10 to 25 %
APP Sensor 1 (Accelerator Pedal Position) Volts
0.2 to 1.0 volts 1.0 to 1.7 volts
APP Sensor 2 (Accelerator Pedal Position) Volts
3.8 to 4.6 volts 3.3 to 3.9 volts
APP Sensor 3 (Accelerator Pedal Position) Volts
3.8 to 4.6 volts 3.7 to 4.0 volts
EGR Solenoid Command %Less than 30 % Less than 30 %
Desired EGR Position %Less than 70 % Less than 80 %
EGR Position %Less than 70 % Less than 80 %
EGR Position Sensor VoltsLess than 2.9 volts Less than 3.1 volts
Intake Throttle Solenoid Command %
Less than 30 % Less than 40 %
Desired Intake Throttle Position %Less than 30 % Less than 80 %
Intake Throttle Position %Less than 30 % Less than 80 %
Intake Throttle Position Sensor Volts Less than 1.6 voltsLess than 3.3 volts
Desired Injection Quantity mm
37 to 12 mm37 to 12 mm3
Main Injection Quantitymm33 to 8 mm35 to 10 mm3
Main Injection Timing°CA 2 to 12 °CA 0 to 10 °CA
Main Injection On Time ms600 to 800 ms 400 to 550 ms
Pre Injection Quantity mm
31 to 4 mm32 to 4 mm3
Pre Injection Interval°CA 3 to 20 °CA 10 to 30 °CA
Fuel Compensation Cyl. 1 mm
3-5.0 to 5.0 mm3 (varies)0.0 mm3
Fuel Compensation Cyl. 2 mm3-5.0 to 5.0 mm3 (varies)0.0 mm3
Fuel Compensation Cyl. 3 mm3-5.0 to 5.0 mm3 (varies)0.0 mm3
Fuel Compensation Cyl. 4 mm3-5.0 to 5.0 mm3 (varies)0.0 mm3
Cylinder Balancing Update Enabled/ Disabled EnabledDisabled
Fuel Supply Pump Status Not Learn/ Learning/ LearnedLearning or Learned
Learning or Learned
Rail Pressure Feedback Mode Wait Mode/ Feedback Mode/ Shutoff Mode Feedback Mode
Feedback Mode
Engine Running Status Off/ Ignition On/ Cranking/ Running Running
Running
Scan Tool Parameter Units Displayed Typical Data Value at Engine Idle Typical Data Value at 2000RPM

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE CONTROL SYSTEM (4JK1/4JJ1) 6E-51
Turbocharger Solenoid Command
This parameter displays the turbocharger nozzle
control solenoid valve control duty ratio based on inputs
to the ECM from various engine sensors. The scan
tool will display a lower percentage when the nozzle is
controlled to open (vacuum pressure supply to the
actuator is reduced). The scan tool will display a higher
percentage when the nozzle is controlled to close
(vacuum pressure supply to the actuator is increased).
Desired Boost Pressure
This parameter displays boost pressure desired by the
ECM based on current driving conditions. This can be
compared to the actual boost pressure to determine
sensor accuracy or turbocharger control problems.
Boost Pressure
This parameter displays the boost pressure in the
intake duct as calculated by the ECM using the signal
from the boost pressure sensor. The scan tool will
display a low boost pressure when the low engine load,
and a high boost pressure when the high engine load.
Note that the true boost pressure is determined by
subtracting barometric pressure from the actual
reading.
Boost Pressure Sensor
This parameter displays the voltage signal sent to the
ECM from the boost pressure sensor. Boost pressure
sensor is a range of value indicating a low voltage
when the boost pressure is low (idle or lower engine
load) and a high voltage when the boost pressure is
high (higher engine load).
Desired Fuel Rail Pressure
This parameter displays fuel rail pressure desired by
the ECM based on current driving conditions. This can
be compared to the actual fuel rail pressure to
determine sensor accuracy or fuel pressure control
problems.
Fuel Rail Pressure
This parameter displays the fuel rail pressure as
calculated by the ECM using the signal from the fuel
rail pressure (FRP) sensor. The scan tool will display a
low pressure when the low engine load, and a high
pressure when the high engine load.
Fuel Rail Pressure Sensor
This parameter displays the voltage signal sent to the
ECM from the fuel rail pressure (FRP) sensor. FRP
sensor is a range of value indicating a low voltage
when the fuel rail pressure is low, and a high voltage
when the fuel rail pressure is high.
FRP Commanded Fuel Flow (Fuel Rail Pressure)
This parameter displays the commanded fuel flow
quantity of the fuel rail pressure (FRP) regulator to the
fuel rail. FRP Regulator Command (Fuel Rail Pressure)
This parameter displays the fuel rail pressure (FRP)
regulator control duty ratio based on inputs to the ECM
from various engine sensors. The scan tool will display
a lower percentage when the FRP regulator is
controlled to open (fuel supply quantity to the fuel rail is
increased). The scan tool will display higher
percentage when the FRP regulator is controlled to
close (fuel supply quantity to the fuel rail is reduced).
FRP Regulator Feedback (Fuel Rail Pressure)
This parameter displays the fuel rail pressure (FRP)
regulator control feedback current as measured by the
ECM. The scan tool will display a low current when the
FRP regulator is controlled to open (fuel supply
quantity to the fuel rail is increased). The scan tool will
display a high current when the FRP regulator is
controlled to close (fuel supply quantity to the fuel rail is
reduced).
Accelerator Pedal Position
This parameter displays the angle of the accelerator
pedal as calculated by the ECM using the signals from
the accelerator pedal position (APP) sensors. The scan
tool will display linearly from 0 to 100% according to the
pedal operation.
APP Sensor 1 (Accelerator Pedal Position)
This parameter displays the voltage signal sent to the
ECM from the accelerator pedal position (APP) sensor
1 of the APP sensor assembly. APP sensor 1 is a
range of value indicating a low voltage when the
accelerator pedal is not depressed, and a high voltage
when the accelerator pedal is fully depressed.
APP Sensor 2 (Accelerator Pedal Position)
This parameter displays the voltage signal sent to the
ECM from the accelerator pedal position (APP) sensor
2 of the APP sensor assembly. APP sensor 2 is a
range of value indicating a high voltage when the
accelerator pedal is not depressed, and a low voltage
when the accelerator pedal is fully depressed.
APP Sensor 3 (Accelerator Pedal Position)
This parameter displays the voltage signal sent to the
ECM from the accelerator pedal position (APP) sensor
3 of the APP sensor assembly. APP sensor 3 is a
range of value indicating a high voltage when the
accelerator pedal is not depressed, and a middle
voltage when the accelerator pedal is fully depressed.
EGR Solenoid Command
This parameter displays the EGR solenoid valve
control duty ratio based on inputs to the ECM from
various engine sensors. The scan tool will display a
lower percentage when the EGR solenoid valve is
controlled to close (EGR gas supply to the intake is
reduced). The scan tool will display a higher
percentage when the EGR solenoid valve is controlled
to open (EGR gas supply to the intake is increased).

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007