2007 INFINITI QX56 relay

INDEX FOR DTC
AT-7
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.DTC
Items
(CONSULT- II screen terms)Reference page OBD- II Except OBD- II
CONSULT- II
GST (*1)C O N S U LT- I I
only “A/T”
— P0615 STARTER RELAY/CIRCAT- 9 4
P0700 P0700 TCMAT- 9 8
P0705 P0705 PNP SW/CIRCAT- 9 9
P0710 P1710 ATF TEMP SEN/CIRCAT- 11 9
P0717 P0717 TURBINE REV S/CIRCAT- 1 0 3
P0720 P0720 VEH SPD SEN/CIR ATAT- 1 0 5
— P0725 ENGINE SPEED SIGAT- 1 0 9
P0740 P0740 TCC SOLENOID/CIRCAT- 111
P0744 P0744 A/T TCC S/V FNCTNAT- 11 3
P0745 P0745 L/PRESS SOL/CIRCAT- 11 5
— P1705 TP SEN/CIRC A/TAT- 11 7
— P1721 VEH SPD SE/CIR·MTRAT- 1 2 4
P1730 P1730 A/T INTERLOCKAT- 1 2 6
— P1731 A/T 1ST E/BRAKINGAT- 1 2 8
P1752 P1752 I/C SOLENOID/CIRCAT- 1 3 0
P1754 (*2) P1754 I/C SOLENOID FNCTNAT- 1 3 2
P1757 P1757 FR/B SOLENOID/CIRCAT- 1 3 4
P1759 (*2) P1759 FR/B SOLENOID FNCTAT- 1 3 6
P1762 P1762 D/C SOLENOID/CIRCAT- 1 3 8
P1764 (*2) P1764 D/C SOLENOID FNCTNAT- 1 4 0
P1767 P1767 HLR/C SOL/CIRCAT- 1 4 2
P1769 P1769 HLR/C SOL FNCTNAT- 1 4 4
P1772 P1772 LC/B SOLENOID/CIRCAT- 1 4 6
P1774 P1774 LC/B SOLENOID FNCTAT- 1 4 8
— P1841 ATF PRES SW 1/CIRCAT- 1 5 0
— P1843 ATF PRES SW 3/CIRCAT- 1 5 2
— P1845 ATF PRES SW 5/CIRCAT- 1 5 4
— P1846 ATF PRES SW 6/CIRCAT- 1 5 6
U1000 U1000 CAN COMM CIRCUITAT- 9 1

AT-32
< SERVICE INFORMATION >
A/T CONTROL SYSTEM
CONTROL SYSTEM DIAGRAM
CAN CommunicationINFOID:0000000003532231
SYSTEM DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. For details, refer to LAN-4,
"CAN Communication System".
SENSORS (or SIGNALS)
⇒TCM
⇒ACTUATORS
PNP switch
Accelerator pedal position sensor
Closed throttle position signal
Wide open throttle position signal
Engine speed signal
A/T fluid temperature sensor
Revolution sensor
Vehicle speed signal
Stop lamp switch signal
Turbine revolution sensor
1st position switch signal
4th position switch signal
ATF pressure switch signal
Tow mode switch signalShift control
Line pressure control
Lock-up control
Engine brake control
Timing control
Fail-safe control
Self-diagnosis
CONSULT-II communication line
Duet-EA control
CAN systemInput clutch solenoid valve
Direct clutch solenoid valve
Front brake solenoid valve
High and low reverse clutch sole-
noid valve
Low coast brake solenoid valve
Torque converter clutch solenoid
valve
Line pressure solenoid valve
A/T CHECK indicator lamp
Starter relay
Back-up lamp relay
SCIA5624E

A/T CONTROL SYSTEM
AT-33
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
Input/Output Signal of TCMINFOID:0000000003532232
*1: Spare for vehicle speed sensor·A/T (revolution sensor)
*2: Spare for accelerator pedal position signal
*3: If these input and output signals are different, the TCM triggers the fail-safe function.
*4: CAN communications
Line Pressure ControlINFOID:0000000003532233
• When an input torque signal equivalent to the engine drive force is sent from the ECM to the TCM, the TCM
controls the line pressure solenoid.
Control itemLine
pressure
controlVehicle
speed
controlShift
controlLock-up
controlEngine
brake
controlFail-safe
function
(*3)Self-diag-
nostics
function
InputAccelerator pedal position signal
(*4)XXXXXXX
Vehicle speed sensor A/T
(revolution sensor)XXXX XX
Vehicle speed sensor MTR
(*1) (*4)XXXX X
Closed throttle position signal
(*4)(*2) X (*2) X X (*2) X X
Wide open throttle position signal
(*4)(*2) X (*2) X (*2) X X
Turbine revolution sensor 1 X X X X X
Turbine revolution sensor 2
(for 4th speed only)XXXXX
Engine speed signals
(*4)XX
PNP switch XXXXXXX
A/T fluid temperature sensors 1, 2 X X X X X X X
ASCDOperation signal
(*4)XXXX
Overdrive cancel sig-
nal
(*4)XXX
TCM power supply voltage signal X X X X X X
Out-
putDirect clutch solenoid (ATF pressure
switch 5)XX XX
Input clutch solenoid (ATF pressure
switch 3)XX XX
High and low reverse clutch sole-
noid (ATF pressure switch 6)XX XX
Front brake solenoid (ATF pressure
switch 1)XX XX
Low coast brake solenoid (ATF
pressure switch 2)XX XXX
Line pressure solenoid X X X X X X X
TCC solenoid X X X
Starter relayXX

TROUBLE DIAGNOSIS
AT-43
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
TROUBLE DIAGNOSIS
DTC Inspection Priority ChartINFOID:0000000003532243
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 1
.
Fail-SafeINFOID:0000000003532244
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is an error in a
main electronic control input/output signal circuit. In fail-safe mode the transmission is fixed in 2nd, 4th or 5th
(depending on the breakdown position), so the customer should feel “slipping” or “poor acceleration”.
Even when the electronic circuits are normal, under special conditions (for example, when slamming on the
brake with the wheels spinning drastically and stopping the tire rotation), the transmission can go into fail-safe
mode. If this happens, switch “OFF” the ignition switch for 10 seconds, then switch it “ON” again to return to
the normal shift pattern. Therefore, the customer's vehicle has returned to normal, so handle according to the
“diagnostics flow” (Refer to AT-44, "
How To Perform Trouble Diagnosis for Quick and Accurate Repair").
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, this function controls the A/T to mark driving possible.
Vehicle Speed Sensor
• Signals are input from two systems - from vehicle speed sensor A/T (revolution sensor) installed on the
transmission and from combination meter so normal driving is possible even if there is a malfunction in one
of the systems. And if vehicle speed sensor A/T (revolution sensor) has unusual cases, 5th gear is prohib-
ited.
Accelerator Pedal Position Sensor
• If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM according
to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow sys-
tems, the engine speed is fixed by ECM to a pre-determined engine speed to make driving possible.
Throttle Position Sensor
• If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM according
to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow sys-
tems, the accelerator opening angle is controlled by the idle signal sent from the ECM which is based on
input indicating either idle condition or off-idle condition (pre-determined accelerator opening) in order to
make driving possible.
PNP Switch
• In the unlikely event that a malfunction signal enters the TCM, the position indicator is switched “OFF”, the
starter relay is switched “OFF” (starter starting is disabled), the back-up lamp relay switched “OFF” (back-up
lamp is OFF) and the position is fixed to the “D” range to make driving possible.
Starter Relay
• The starter relay is switched “OFF”. (Starter starting is disabled.)
A/T Interlock
• If there is an A/T interlock judgment malfunction, the transmission is fixed in 2nd gear to make driving possi-
ble.
NOTE:
When the vehicle is driven fixed in 2nd gear, a turbine revolution sensor malfunction is displayed,
but this is not a turbine revolution sensor malfunction.
• When the coupling pattern below is detected, the fail-safe action corresponding to the pattern is performed.
A/T INTERLOCK COUPLING PATTERN TABLE
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above

TROUBLE DIAGNOSIS
AT-83
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
PCONSULT-II Function (A/T)INFOID:0000000003532259
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II REFERENCE VALUE
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man-
ual may differ slightly. This occurs because of the following reasons:
- Actual shift schedule has more or less tolerance or allowance,
- Shift schedule indicated in Service Manual refers to the point where shifts start, and
- Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
9 B/R Starter relaySelector lever in “N”,“ P” positions. Battery voltage
Selector lever in other positions. 0V
10 B Ground Always 0V Te r m i n a l
No.Wire
colorItem Condition Data (Pyrex.)
TCM diagnostic mode Description
WORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the TCM for setting the status
suitable for required operation, input/output signals are received from the TCM and received data is
displayed.
SELF-DIAG RESULTS Displays TCM self-diagnosis results.
DATA MONITOR Displays TCM input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
FUNCTION TEST Conducted by CONSULT-II instead of a technician to determine whether each system is “OK” or “NG”.
ECU PART NUMBER TCM part number can be read.
Item name Condition Display value (Approx.)
ATF TEMP SE 1
0°C (32° F) - 20°C (68°F) - 80°C (176°F)3.3 - 2.7 - 0.9 V
ATF TEMP SE 23.3 - 2.5 - 0.7 V
TCC SOLENOIDWhen perform slip lock-up 0.2 - 0.4 A
When perform lock-up 0.4 - 0.6 A
SLCT LVR POSISelector lever in “N”,“P” position. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “4” position. 4
Selector lever in “3” position. 3
Selector lever in “2” position. 2
Selector lever in “1” position. 1
VHCL/S SE·A/T During drivingApproximately matches the
speedometer reading.
ENGINE SPEED Engine runningClosely matches the tachometer
reading.

AT-84
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
CONSULT-II START PROCEDURE
Refer to GI-36, "CONSULT-II Start Procedure".
SELF-DIAGNOSTIC RESULT MODE
Operation Procedure
After performing SELF-DIAGNOSTIC RESULT MODE, place check marks for results on the AT-44, "How To
Perform Trouble Diagnosis for Quick and Accurate Repair". Reference pages are provided following the items.
Display Items List
LINE PRES SOL During driving 0.2 - 0.6 A
TURBINE REV During driving (lock-up ON)Approximately matches the en-
gine speed.
VHCL/S SE·MTR During drivingApproximately matches the
speedometer reading.
ATF PRES SW 1Front brake engaged. Refer to AT- 2 0
ON
Front brake disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 2Low coast brake engaged. Refer to AT- 2 0
ON
Low coast brake disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 3Input clutch engaged. Refer to AT- 2 0
ON
Input clutch disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 5Direct clutch engaged. Refer to AT- 2 0
ON
Direct clutch disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 6High and low reverse clutch engaged. Refer to AT- 2 0
ON
High and low reverse clutch disengaged. Refer to AT- 2 0
OFF
I/C SOLENOIDInput clutch disengaged. Refer to AT- 2 0
0.6 - 0.8 A
Input clutch engaged. Refer to AT- 2 0
0 - 0.05 A
FR/B SOLENOIDFront brake engaged. Refer to AT- 2 0
0.6 - 0.8 A
Front brake disengaged. Refer to AT- 2 0
0 - 0.05 A
D/C SOLENOIDDirect clutch disengaged. Refer to AT- 2 0
0.6 - 0.8 A
Direct clutch engaged. Refer to AT- 2 0
0 - 0.05 A
HLR/C SOLHigh and low reverse clutch disengaged. Refer to AT- 2 0
0.6 - 0.8 A
High and low reverse clutch engaged. Refer to AT- 2 0
0 - 0.05 A
ON OFF SOLLow coast brake engaged. Refer to AT- 2 0
ON
Low coast brake disengaged. Refer to AT- 2 0
OFF
STARTER RELAYSelector lever in “N”,“P” position. ON
Selector lever in other position. OFF
ACCELE POSIReleased accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8/8
CLSD THL POSReleased accelerator pedal. ON
Fully depressed accelerator pedal. OFF
W/O THL POSFully depressed accelerator pedal. ON
Released accelerator pedal. OFF
BRAKE SWDepressed brake pedal. ON
Released brake pedal. OFF Item name Condition Display value (Approx.)

TROUBLE DIAGNOSIS
AT-85
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
X: Applicable, —: Not applicable
Items (CONSULT-II
screen terms)Malfunction is detected when...TCM self-di-
agnosisOBD-II (DTC)
“A/T” with
CONSULT-IIMIL indicator
lamp*1, “EN-
GINE” with
CONSULT-II or
GST
CAN COMM CIRCUIT • When a malfunction is detected in CAN communications U1000 U1000
STARTER RELAY/
CIRC• If this signal is ON other than in P or N position, this is judged to be a
malfunction.
(And if it is OFF in P or N position, this too is judged to be a malfunction.)P0615 —
TCM • TCM is malfunctioning. P0700 P0700
PNP SW/CIRC• PNP switch 1-4 signals input with impossible pattern
• “P” position is detected from N position without any other position being
detected in between.P0705 P0705
TURBINE REV S/CIRC• TCM does not receive the proper voltage signal from the sensor.
• TCM detects an irregularity only at position of 4th gear for turbine revo-
lution sensor 2.P0717 P0717
VEH SPD SEN/CIR AT
(Revolution sensor)• Signal from vehicle speed sensor A/T (Revolution sensor) not input due
to cut line or the like
• Unexpected signal input during running
• After ignition switch is turned ON, unexpected signal input from vehicle
speed sensor MTR before the vehicle starts movingP0720 P0720
ENGINE SPEED SIG • TCM does not receive the CAN communication signal from the ECM. P0725 —
TCC SOLENOID/CIRC • Normal voltage not applied to solenoid due to cut line, short, or the like P0740 P0740
A/T TCC S/V FNCTN• A/T cannot perform lock-up even if electrical circuit is good.
• TCM detects as irregular by comparing difference value with slip rota-
tion.P0744 P0744*2
L/PRESS SOL/CIRC• Normal voltage not applied to solenoid due to cut line, short, or the like
• TCM detects as irregular by comparing target value with monitor value.P0745 P0745
TP SEN/CIRC A/T• TCM does not receive the proper accelerator pedal position signals (in-
put by CAN communication) from ECM.P1705 P1705
ATF TEMP SEN/CIRC• During running, the ATF temperature sensor signal voltage is exces-
sively high or lowP1710 P0710
VEH SPD SE/CIR·MTR• Signal (CAN communication) from vehicle speed sensor MTR not input
due to cut line or the like
• Unexpected signal input during runningP1721 —
A/T INTERLOCK• Except during shift change, the gear position and ATF pressure switch
states are monitored and comparative judgement made.P1730 P1730
A/T 1ST E/BRAKING• Each ATF pressure switch and solenoid current is monitored and if a
pattern is detected having engine braking 1st gear other than in the "1"
position, a malfunction is detected.P1731 —
I/C SOLENOID/CIRC• Normal voltage not applied to solenoid due to functional malfunction,
cut line, short, or the like
• TCM detects as irregular by comparing target value with monitor value.P1752 P1752
I/C SOLENOID FNCTN • TCM detects that actual gear ratio is irregular, and relation between
gear position and condition of ATF pressure switch 3 is irregular during
depressing accelerator pedal. (Other than during shift change)
• TCM detects that relation between gear position and condition of ATF
pressure switch 3 is irregular during releasing accelerator pedal. (Other
than during shift change)P1754 P1754*2
FR/B SOLENOID/CIRC• Normal voltage not applied to solenoid due to functional malfunction,
cut line, short, or the like
• TCM detects as irregular by comparing target value with monitor value.P1757 P1757

TROUBLE DIAGNOSIS
AT-89
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
DTC WORK SUPPORT MODE
Display Items List
ATF WARN LAMP (ON-OFF display) — — X
BACK-UP LAMP (ON-OFF display) — — X
STARTER RELAY (ON-OFF display) — — X
PNP SW3 MON (ON-OFF display) — — X
C/V CLB ID1 — — X
C/V CLB ID2 — — X
C/V CLB ID3 — — X
UNIT CLB ID1 — — X
UNIT CLB ID2 — — X
UNIT CLB ID3 — — X
TRGT GR RATIO — — X
TRGT PRES TCC (kPa) — — X
TRGT PRES L/P (kPa) — — X
TRGT PRES I/C (kPa) — — X
TRGT PRE FR/B (kPa) — — X
TRGT PRES D/C (kPa) — — X
TRG PRE HLR/C (kPa) — — X
SHIFT PATTERN — — X
DRV CST JUDGE — — X
START RLY MON — — X
NEXT GR POSI — — X
SHIFT MODE — — X
MANU GR POSI — — X
VEHICLE SPEED (km/h) — XX Vehicle speed recognized by the TCM.
Voltage (V) — — XDisplays the value measured by the voltage
probe.
Frequency (Hz) — — X
The value measured by the pulse probe is dis-
played. DUTY-HI (high) (%) — — X
DUTY-LOW (low) (%) — — X
PLS WIDTH-HI (ms) — — X
PLS WIDTH-LOW (ms) — — XMonitored item (Unit)Monitor Item Selection
Remarks ECU IN-
PUT SIG-
NALSMAIN SIG-
NALSSELEC-
TION
FROM
MENU
DTC work support itemDescription Check item
I/C SOL FUNCTN CHECK* — —
FR/B SOL FUNCTN CHECK* — —
D/C SOL FUNCTN CHECK* — —
HLR/C SOL FUNCTN CHECK* — —