2AZ-FE ENGINE CONTROL SYSTEM – SFI SYSTEMES–47
ES
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
By reading the DATA LIST displayed on an intelligent
tester, values can be checked, including those of the
switches, sensors, and actuators, without removing any
parts. Reading the DATA LIST as the first step of
troubleshooting is one method of shortening diagnostic
time.
NOTICE:
In the table below, the values listed under Normal
Condition are for reference only. Do not depend
solely on these values when determining whether or
not a part is faulty.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the intelligent tester to the DLC3.
(d) Turn the ignition switch ON.
(e) Turn the tester ON.
(f) Select the following menu items: DIAGNOSIS /
ENHANCED OBD II / DATA LIST.
(g) Check the values by referring to the table below.
ECM:
Intelligent Tester Display Measurement: Range (Display) Normal Condition*1 Diagnostic Note
INJECTORInjection period of No. 1 cylinder:
Min.: 0 ms, Max.: 32.64 ms1.0 to 3.0 ms: Idling -
IGN ADVANCE Ignition timing advance for No. 1
cylinder:
Min.: -64 deg, Max.: 63.5 degBTDC 0 to 14 deg: Idling -
CALC LOADCalculated load by ECM:
Min.: 0 %, Max.: 100 %• 10 to 30 %: Idling
• 10 to 30 %: Running without
load at 2,500 rpmLoad value
VEHICLE LOADVehicle load:
Min.: 0 %, Max.: 25,700 %Actual vehicle loadLoad percentage in terms of
maximum intake air flow amount
MAFAir flow rate from Mass Air Flow
(MAF) meter:
Min.: 0 g/sec., Max.: 655.35 g/sec.1 to 3 g/sec.: Idling
2 to 6 g/sec.: Running without
load at 2,500 rpmIf value approximately 0.0 g/sec.:
• MAF meter power source
circuit open
• VG circuit open or short
If value 160.0 g/sec. or more:
• E2G circuit open
ENGINE SPDEngine speed:
Min.: 0 rpm, Max.: 16,383.75 rpm650 to 750 rpm: Idling -
VEHICLE SPDVehicle speed:
Min.: 0 km/h, Max.: 255 km/hActual vehicle speed Speed indicated on speedometer
COOLANT TEMPEngine coolant temperature:
Min.: -40
C, Max.: 140C80 to 100C (176 to 212F):
After warming up• If -40
C (-40F): sensor circuit
open
• If 140
C (284F) or more:
sensor circuit shorted
INTAKE AIRIntake air temperature:
Min.: -40
C, Max.: 140CEquivalent to ambient air
temperature• If -40
C (-40F): sensor circuit
open
• If 140
C (284F) or more:
sensor circuit shorted
AIR-FUEL RATIORatio compared to stoichiometric
level:
Min.: 0, Max.: 1.9990.8 to 1.2: Idling• Less than 1 (0 to 0.999) =
Lean
• Stoichiometric air-fuel ratio = 1
• Greater than 1 (1.001 to
1.999) = Rich
ES–542AZ-FE ENGINE CONTROL SYSTEM – SFI SYSTEM
ES
HINT:
• *1: If no idling conditions are specified, the transmission
gear selector lever should be in the N or P position, and
the A/C switch and all accessory switches should be OFF.
• *2: DATA LIST values are only displayed when performing
the following ACTIVE TEST: VVT B1. For other ACTIVE
TESTs, the DATA LIST value will be 0.
2. ACTIVE TEST
HINT:
Performing an ACTIVE TEST enables components
including the relays, VSV (Vacuum Switching Valve) and
actuators, to be operated without removing any parts.
The ACTIVE TEST can be performed with the intelligent
tester. Performing the ACTIVE TEST as the first step of
troubleshooting is one method of shortening diagnostic
time.
DATA LIST can be displayed during ACTIVE TEST.
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch ON.
CCM CMPLComprehensive component
monitor:
COMPL or INCMPL--
FUEL ENAFuel system monitor:
UNABLE or ENABLE--
FUEL CMPLFuel system monitor:
COMPL or INCMPL--
MISFIRE ENAMisfire monitor:
UNABLE or ENABLE--
MISFIRE CMPLMisfire monitor:
COMPL or INCMPL--
HTR ENAO2S (A/FS) heater monitor:
UNABLE or ENABLE--
HTR CMPLO2S (A/FS) heater monitor:
COMPL or INCMPL--
O2S (A/FS) ENAO2S (A/FS) monitor:
UNABLE or ENABLE--
O2S (A/FS) CMPLO2S (A/FS) monitor:
COMPL or INCMPL--
EVAP ENAEVAP monitor:
UNABLE or ENABLE--
EVAP CMPLEVAP monitor:
COMPL or INCMPL--
CAT ENACatalyst monitor:
UNABLE or ENABLE--
CAT CMPLCatalyst monitor:
COMPL or INCMPL--
MODEL CODE Identifying model code ACA3# -
ENGINE TYPE Identifying engine type 2AZFE -
CYLINDER NUMBERIdentifying cylinder number:
Min.: 0, Max.: 2554-
TRANSMISSION Identifying transmission type 4AT -
DESTINATION Identifying destination A (America) -
MODEL YEARIdentifying model year:
Min.: 1900, Max.: 2155200# -
SYSTEM Identifying engine system GASLIN (gasoline engine) -Intelligent Tester Display Measurement: Range (Display) Normal Condition*1 Diagnostic Note
