2006 NISSAN VERSA brake

AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-29
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: June 20062007 Versa
COAST OPERATION
When the SET/COAST switch is depressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is depressed after cancel operation other than depressing MAIN
switch is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition
must meet following conditions.

Brake pedal is released.

Clutch pedal is released (M/T models)

Selector lever is in other than P and N positions (A/T and CVT models)

Vehicle speed is greater than 40 km/h (25 MPH) and less than 144 km/h (89 MPH)
Component DescriptionUBS00QB7
ASCD STEERING SWITCH
Refer to EC-466 .
ASCD BRAKE SWITCH
Refer to EC-473 and EC-549 .
ASCD CLUTCH SWITCH
Refer to EC-473 and EC-549 .
STOP LAMP SWITCH
Refer to EC-473 , EC-488 and EC-549 .
ELECTRIC THROTTLE CONTROL ACTUATOR
Refer to EC-493 , EC-499 , EC-506 and EC-511 .
ASCD INDICATOR
Refer to EC-559 .

EC-50Revision: June 2006
ON BOARD DIAGNOSTIC (OBD) SYSTEM
2007 Versa
ENGINE SPEED SIG P0725 0725 — — 2×AT- 11 3
A/T 1ST GR FNCTN P0731 0731 — — 2×AT- 11 7
A/T 2ND GR FNCTN P0732 0732 — — 2×AT- 1 2 1
A/T 3RD GR FNCTN P0733 0733 — — 2×AT- 1 2 4
A/T 4TH GR FNCTN P0734 0734 — — 2×AT- 1 2 8
TCC SOLENOID/CIRC P0740 0740 — — 2×AT- 1 3 4
A/T TCC S/V FNCTN P0744 0744 — — 2×AT- 1 3 9
(A/T),
CVT-110

(CVT)
L/PRESS SOL/CIRC P0745 0745 — — 2×AT- 1 4 5
PRS CNT SOL/A FCTN P0746 0746 — — 1×CVT-118
SFT SOL A/CIRC P0750 0750 — — 1×AT- 1 5 1
SFT SOL B/CIRC P0755 0755 — — 1×AT- 1 5 6
PRS CNT SOL/B FCTN P0776 0776 — — 2×CVT-121
PRS CNT SOL/B CIRC P0778 0778 — — 2×CVT-124
TR PRS SENS/A CIRC P0840 0840 — — 2×CVT-129
TR PRS SENS/B CIRC P0845 0845 — — 2×CVT-137
P-N POS SW/CIRCUIT P0850 0850 — — 2×EC-436
C L O S E D L O O P - B 1 P 11 4 8 11 4 8 — — 1×EC-442
ENG OVER TEMP P1217 1217 — — 1×EC-443
CTP LEARNING P1225 1225 — — 2 —EC-460
CTP LEARNING P1226 1226 — — 2 —EC-462
COLD START CONTROL P1421 1421 — — 2×EC-464
ASCD SW P1564 1564 — — 1 —EC-466
ASCD BRAKE SW P1572 1572 — — 1 —EC-473
ASCD VHL SPD SEN P1574 1574 — — 1 —EC-483
NATS MALFUNCTIONP1610 -
P16151610 - 1615 — — 2 —BL-212
TP SEN/CIRC A/T P1705 1705 — — 1×CVT-150
IN PULY SPEED P1715 1715 — — 2 —EC-485 (A/T),
EC-486
(CVT)
LU-SLCT SOL/CIRC P1740 1740 — — 2×CVT-158
O/R CLTCH SOL/CIRC P1760 1760 — — 2×AT- 1 6 1
STEP MOTR CIRC P1777 1777 — — 1×CVT-164
STEP MOTR FNC P1778 1778 — — 2×CVT-168
BRAKE SW/CIRCUIT P1805 1805 — — 2 —EC-488
ETC MOT PWR P2100 2100 — — 1×EC-493
ETC FUNCTION/CIRC P2101 2101 — — 1×EC-499
ETC MOT PWR P2103 2103 — — 1×EC-493
ETC MOT P2118 2118 — — 1×EC-506
ETC ACTR P2119 2119 — — 1×EC-511
APP SEN 1/CIRC P2122 2122 — — 1×EC-513
APP SEN 1/CIRC P2123 2123 — — 1×EC-513
APP SEN 2/CIRC P2127 2127 — — 1×EC-519
Items
(CONSULT-II screen terms)DTC*
1
SRT codeTe s t v a l u e /
Test limit
(GST only)TripMIL light-
ing upReference
page CONSULT-II
GST*
2ECM*3

EC-78Revision: June 2006
BASIC SERVICE PROCEDURE
2007 Versa
Throttle Valve Closed Position LearningUBS00QO9
DESCRIPTION
Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by
monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume LearningUBS00QOA
DESCRIPTION
Idle Air Volume Learning is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:

Each time electric throttle control actuator or ECM is replaced.

Idle speed or ignition timing is out of specification.
PREPARATION
Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.

Battery voltage: More than 12.9V (At idle)

Engine coolant temperature: 70 - 95°C (158 - 203°F)

Park/neutral position (PNP) switch: ON

Electric load switch: OFF
[Air conditioner (models with A/C), headlamp, rear window defogger]
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine
is started the headlamp will not be illuminated.

Steering wheel: Neutral (Straight-ahead position)

Vehicle speed: Stopped

Transmission: Warmed-up
–Models with CONSULT-II (A/T and CVT models)
 Drive vehicle until “FLUID TEMP SE” in “DATA MONITOR” mode of “A/T” or “CVT” system indicates less
than 0.9V.
–Models without CONSULT-II (A/T and CVT models) and M/T models
 Drive vehicle for 10 minutes.

EC-90Revision: June 2006
TROUBLE DIAGNOSIS
2007 Versa
2
P0031 P0032 Air fuel ratio (A/F) sensor 1 heater

P0037 P0038 Heated oxygen sensor 2 heater

P0075 Intake valve timing control solenoid valve

P0130 P0131 P0132 P0133 P2A00 Air fuel ratio (A/F) sensor 1

P0137 P0138 P0139 Heated oxygen sensor 2

P0441 EVAP control system purge flow monitoring

P0443 P0444 P0445 EVAP canister purge volume control solenoid valve

P0447 P0448 EVAP canister vent control valve

P0451 P0452 P0453 EVAP control system pressure sensor

P1217 Engine over temperature (OVERHEAT)

P1805 Brake switch

P2100 P2103 Throttle control motor relay

P2101 Electric throttle control function

P2118 Throttle control motor
3

P0011 Intake valve timing control

P0171 P0172 Fuel injection system function

P0300 - P0304 Misfire

P0420 Three way catalyst function

P0442 P0456 EVAP control system (SMALL LEAK, VERY SMALL LEAK)

P0455 EVAP control system (GROSS LEAK)

P0506 P0507 Idle speed control system

P0710 P0715 P0720 P0725 P0731 P0732 P0733 P0734 P0740 P0744 P0745 P0746 P0750 P0755 P0776 P0778
P0840 P0845 P1705 P1740 P1760 P1777 P1778 A/T or CVT related sensors, solenoid valves and switches

P1148 Closed loop control

P1421 Cold start control

P1564 ASCD steering switch

P1572 ASCD brake switch

P1574 ASCD vehicle speed sensor

P1715 Turbine revolution sensor (A/T), Primary speed sensor (CVT)

P2119 Electric throttle control actuator Priority Detected items (DTC)

TROUBLE DIAGNOSIS
EC-101
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: June 20062007 Versa
1. Stop lamp switch 2. ASCD brake switch 3. ASCD clutch switch
4. Clutch pedal 5. ASCD steering switch 6. MAIN switch
7. CANCEL switch 8. SET/COAST switch 9. RESUME/ACCELERATOR switch
10. EVAP control system pressure sen-
sor (This illustration is a view from
under vehicle)11. EVAP canister 12. EVAP canister vent control valve
BBIA0728E

TROUBLE DIAGNOSIS
EC-111
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: June 20062007 Versa
73 PIntake valve timing control
solenoid valve[Engine is running]

Warm-up condition

Idle speedBATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

When revving engine up to 2,000 rpm
quickly7 - 10V
74 WSensor power supply
(Refrigerant pressure
sensor)[Ignition switch: ON]Approximately 5V
75 BRSensor power supply
[Crankshaft position sensor
(POS)][Ignition switch: ON]Approximately 5V
76 WEVAP control system pres-
sure sensor power supply[Ignition switch: ON]Approximately 5V
78 OSensor power supply
[Camshaft position sensor
(PHASE)][Ignition switch: ON]Approximately 5V
83 P CAN communication line[Ignition switch: ON]Approximately 1.7 - 2.3V
Output voltage varies with the
communication status.
84 L CAN communication line[Ignition switch: ON]Approximately 2.6 - 3.2V
Output voltage varies with the
communication status.
88 LG DATA link connector[Ignition switch: ON]

CONSULT-II or GST: Disconnected.Approximately 10.5V
93 O Ignition switch[Ignition switch: OFF]0V
[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
94 R ASCD steering switch[Ignition switch: ON]

ASCD steering switch: OFFApproximately 4V
[Ignition switch: ON]

MAIN switch: PressedApproximately 0V
[Ignition switch: ON]

CANCEL switch: PressedApproximately 1V
[Ignition switch: ON]

RESUME/ACCELERATE switch: PressedApproximately 3V
[Ignition switch: ON]

SET/COAST switch: PressedApproximately 2V
95 BSensor ground
(ASCD steering switch)[Engine is running]

Warm-up condition

Idle speedApproximately 0V
99 R Stop lamp switch[Ignition switch: OFF]

Brake pedal: Fully releasedApproximately 0V
[Ignition switch: OFF]

Brake pedal: Slightly depressedBATTERY VOLTAGE
(11 - 14V) TERMI-
NAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIA4937J

EC-112Revision: June 2006
TROUBLE DIAGNOSIS
2007 Versa
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)100 G ASCD brake switch[Ignition switch: ON]

Brake pedal: Slightly depressed (A/T, CVT)

Brake pedal and/or clutch pedal: Slightly
depressed (M/T)Approximately 0V
[Ignition switch: ON]

Brake pedal: Fully released (A/T, CVT)

Brake pedal and clutch pedal: Fully
released (M/T)BATTTERY VOLTAGE
(11 - 14V)
102 SBSensor power supply
(Accelerator pedal position
sensor 2)[Ignition switch: ON]Approximately 5V
103 GRAccelerator pedal position
sensor 2[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully released0.3 - 0.6V
[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully depressed1.95 - 2.4V
104 YSensor ground
(Accelerator pedal position
sensor 2)[Engine is running]

Warm-up condition

Idle speedApproximately 0V
105 G Power supply for ECM[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
106 PSensor power supply
(Accelerator pedal position
sensor 1)[Ignition switch: ON]Approximately 5V
108 B ECM ground[Engine is running]

Idle speedBody ground
11 0 GAccelerator pedal position
sensor 1[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully released0.6 - 0.9V
[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully depressed3.9 - 4.7V
111 RSensor ground
(Accelerator pedal position
sensor 1)[Engine is running]

Warm-up condition

Idle speedApproximately 0V TERMI-
NAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)

EC-114Revision: June 2006
TROUBLE DIAGNOSIS
2007 Versa
ENGINE CONTROL COMPONENT PARTS/CONTROL SYSTEMS APPLICATION
ItemDIAGNOSTIC TEST MODE
WORK
SUP-
PORTSELF-DIAGNOSTIC
RESULTS
DATA
MONI-
TORDATA
MONI-
TOR
(SPEC)ACTIVE
TESTDTC & SRT
CONFIRMATION
DTC*
1 FREEZE
FRAME
DATA*
2
SRT
STATUSDTC
WORK
SUP-
PORT
ENGINE CONTROL COMPONENT PARTS
INPUT
Crankshaft position sensor (POS)××××
Camshaft position sensor (PHASE)××××
Mass air flow sensor×××
Engine coolant temperature sensor×××××
Air fuel ratio (A/F) sensor 1×××××
Heated oxygen sensor 2×××××
Wheel sensor××××
Accelerator pedal position sensor×××
Throttle position sensor× ×××
Fuel tank temperature sensor××××
EVAP control system pressure
sensor×××
Intake air temperature sensor××××
Knock sensor×
Refrigerant pressure sensor*
4××
Closed throttle position switch
(Accelerator pedal position sensor
signal)××
Air conditioner switch××
Park/neutral position (PNP) switch×××
Stop lamp switch×××
Battery voltage××
Load signal ××
Fuel level sensor×××
ASCD steering switch×××
ASCD brake switch×××
ASCD clutch switch×××
EPS control unit××