2006 NISSAN VERSA oil capacity

2007
QUICK REFERENCE CHART: VERSA

Refill CapacitiesELS00257
DescriptionCapacity (Approximate)
Liter US measure Imp measure
Fuel50.0 13 1/4 gal 11 gal
Engine oil
Drain and refillWith oil filter change 3.9 4 1/8 qt 3 3/8 qt
Without oil filter change 3.7 3 7/8 qt 3 1/4 qt
Dry engine (engine overhaul) 4.9 5 1/8 qt 4 3/8 qt
Cooling system
(with reservoir at max level)6.8 7 1/4 qt 6 qt
Manual transaxle fluid (MTF) 2.0 4 1/4 pt 3 1/2 pt
Automatic transaxle fluid (ATF) 7.9 8 3/8 qt 7 qt
CVT fluid8.3 8 3/4 qt 7 1/4 qt
Brake and clutch fluid — — —
Multi-purpose grease — — —
Windshield washer fluid 4.5 4 3/4 qt 4 qt
Air conditioning system refrigerant 0.45 ± 0.05 kg 0.99 ± 0.11 lb 0.99 ± 0.11 lb
Air conditioning system oilType 1
120 m4.1 fl oz 4.2 fl oz
Type 2
100 m3.4 fl oz 3.5 fl oz

A/T FLUID
AT-17
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
Changing A/T FluidUCS005M9
1. Warm up A/T fluid.
2. Stop engine.
3. Drain A/T fluid by removing the drain plug. Reinstall the drain plug to the specified torque.
CAUTION:
Do not reuse drain plug gasket.
4. Refill the transaxle with new specified A/T fluid through the A/T fluid charging pipe. Always refill the tran-
saxle with the same volume of A/T fluid that was drained out.
5. Run engine at idle speed for 5 minutes.
6. Check A/T fluid level and condition. Refer to AT- 1 6 , "
Checking A/T Fluid" .
A/T Fluid Cooler CleaningUCS006KH
Whenever the A/T is repaired, overhauled, or replaced, the A/T fluid cooler mounted in the radiator must be
inspected and cleaned.
Metal debris and friction material, if present, can become trapped in the A/T fluid cooler. This debris can con-
taminate the newly serviced A/T or, in severe cases, can block or restrict the flow of A/T fluid. In either case,
malfunction of the newly serviced A/T may result.
Debris, if present, may build up as A/T fluid enters the cooler inlet. It will be necessary to back flush the cooler
through the cooler outlet in order to flush out any built up debris.
A/T FLUID COOLER CLEANING PROCEDURE
1. Identify the A/T inlet and outlet fluid cooler hoses.
2. Position an oil pan under the A/T inlet and outlet fluid cooler
hoses.
3. Disconnect the A/T fluid cooler inlet and outlet rubber hoses
from the steel cooler tubes or bypass valve.
NOTE:
Replace the cooler hoses if rubber material from the hose
remains on the tube fitting.
4. Allow any A/T fluid that remains in the cooler hoses to drain into
the oil pan.
5. Insert the extension adapter hose of a can of Transmission
Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.
CAUTION:

Wear safety glasses and rubber gloves when spraying
the Transmission Cooler Cleaner.

Spray Transmission Cooler Cleaner only with adequate
ventilation.

Avoid contact with eyes and skin.

Do not breath vapors or spray mist.
6. Hold the hose and can as high as possible and spray Transmis-
sion Cooler Cleaner in a continuous stream into the cooler outlet hose until A/T fluid flows out of the cooler
inlet hose for 5 seconds. Drain plug: Refer to AT- 2 5 7 , "
Components" .
Fluid grade and capacity: Refer to MA-11, "
RECOMMENDED FLUIDS AND LUBRICANTS" .
SCIA5628E
SCIA5629E

EM-78Revision: June 2006
CYLINDER BLOCK
2007 Versa
Disassembly and AssemblyEBS00U7X
DISASSEMBLY
1. Remove engine and transaxle assembly from vehicle, separate transaxle from engine. Refer to EM-73,
"ENGINE ASSEMBLY" .
2. Install engine to engine stand as follows;
a. Remove flywheel (M/T models) or drive plate (1) (A/T or CVT
models).

Secure flywheel (M/T models) or drive plate (A/T or CVT mod-
els) using Tool (A), and remove bolts.
CAUTION:
Be careful not to damage or scratch drive plate (A/T or CVT
models) and contact surface for clutch disc of flywheel (M/T
models).
NOTE:
Figure shows drive plate (A/T or CVT models)
b. Lift the engine with a hoist to install it onto widely use engine stand.
CAUTION:

Use the engine stand that has a load capacity [approximately 135 kg (298 lb) or more] large
enough for supporting the engine weight.

If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the
potential risk of overturning stand.
–Exhaust manifold; Refer to EM-21, "EXHAUST MANIFOLD" .
–Rocker cover; Refer to EM-30, "IGNITION COIL, SPARK PLUG AND ROCKER COVER" .
NOTE:
The figure shows an example of widely used engine stand (A)
that can support mating surface of transaxle with flywheel (M/T
models) or drive plate (A/T or CVT models) removed.
CAUTION:
Before removing the hanging chains, make sure the engine
stand is stable and there is no risk of overturning.
3. Remove oil pan (upper and lower). Refer to EM-24, "
OIL PAN" .
4. Remove cylinder head. Refer to EM-62, "
CYLINDER HEAD" .
5. Remove thermostat housing. Refer to CO-18, "
THERMOSTAT" .
1. Cylinder block 2. O-ring 3. Crankshaft position sensor (POS)
4.Crankshaft position sensor (POS)
cover5.Oil filter (for intake valve timing con-
trol)6. Knock sensor
7. Oil pressure switch 8. Top ring 9. Second ring
10. Oil ring 11. Snap ring 12. Piston
13. Piston pin 14. Connecting rod 15. Thrust bearing
16. Connecting rod bearing upper 17. Main bearing upper 18. Crankshaft key
19. Main bearing lower 20. Connecting rod bearing lower 21. Connecting rod bearing cap
22. Connecting rod bolt 23. Main bearing cap 24. Main bearing cap bolt
25. Crankshaft 26. Pilot converter (A/T or CVT models) 27. Signal plate
28. Rear oil seal 29. Drive plate (A/T or CVT models) 30. Reinforcement plate (A/T or CVT
models)
31. Flywheel (M/T models) 32. Block heater (Canada only) A. Refer to EM-81
Tool number : KV 11105210 (J-44716)
PBIC3226J
PBIC3227J

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
K
KEYLES - Wiring diagram .................................. BL-57
Knock sensor (KS) .......................................... EC-315
KS - Wiring diagram ........................................ EC-316
L
L/USSV - Wiring diagram .............................. CVT-159
Line pressure and secondary pressure control CVT-26
Line pressure solenoid valve ......... CVT-113, CVT-118
Line pressure test (A/T) ...................................... AT-56
Liquid gasket application ................ EM-5, LU-2, CO-3
Location of electrical units ................................. PG-64
Lock-up and select control .............................. CVT-28
Lock-up select solenoid valve ....................... CVT-158
Low tire pressure warning system ....................... WT-7
Low tire pressure warning system - trouble diagnoses
WT-10
Low tire pressure warning system - Wiring diagram ....
WT-10
LPSV - Wiring diagram .................... AT-146, CVT-114
Lubricant (R134a) A/C ...................... MTC-5, MTC-18
Lubrication circuit (engine) ................................... LU-4
Lubrication oil A/C .......................................... MTC-96
M
M/T major overhaul ........................................... MT-17
M/T removal and installation ............................. MT-15
MAFS - Wiring diagram ..................... EC-181, EC-189
Magnet clutch ................................................. MTC-41
MAIN - Wiring diagram ...................... EC-144, AT-183
Mainshaft (M/T) ................................................. MT-18
Maintenance ........................................................ MA-5
Malfunction indicator lamp (MIL) ....................... EC-61
Manual air conditioner - Wiring diagram ........ MTC-29
Mass air flow sensor (MAFS) ............ EC-178, EC-187
Master cylinder (clutch) ........................................ CL-9
Meter ..................................................................... DI-5
METER - Wiring diagram ...................................... DI-9
MIL data link connectors circuit ....................... EC-592
MIRROR - Wiring diagram ............................... GW-64
Mirror, door ....................................................... GW-65
Mirror, out side ................................................. GW-65
Misfire .............................................................. EC-308
Mode door control linkage adjustment ........... MTC-71
Molding - See Exterior .............................. EI-23, EI-24
Mud guard - See Exterior .................................... EI-26
Multiport fuel injection (MFI) system ................. EC-23
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ................................................................ BL-54
N
NATS - Wiring diagram .................................... BL-215
NATS (Nissan anti-theft system) precautions ...... GI-3
NONDTC - Wiring diagram ............. AT-193, CVT-176
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (RSU) ............................. RSU-4
NVIS (Nissan vehicle immobilizer system) ....... BL-212
O
Oil change (capacity) ......................................... MA-11
Oil cooler (engine) ............................................. EM-24
Oil filter ................................................................ LU-8
Oil pan (engine) ................................................. EM-24
Oil pressure (engine) ........................................... LU-5
Oil seal replacement (engine) . EM-24, EM-37, EM-59,
EM-66
On board diagnostic system .............................. EC-47
ORVR (On-board Refueling Vapor Recovery) ... EC-38
Out side mirror .................................................. GW-65
Overdrive control switch ..................... AT-186, AT-191
Overheat .......................................................... EC-443
OVRCSV - Wiring diagram .............................. AT-162
P
P/SCKT - Wiring diagram ................................ WW-44
Park/Neutral position switch ............................ EC-436
Park/neutral position switch (A/T) ......... AT-97, AT-186
Park/neutral position switch (CVT) .................. CVT-78
Park/neutral position switch (M/T) ..................... MT-11
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................. EC-44
Periodic maintenance .......................................... MA-7
PGC/V - Wiring diagram .................... EC-356, EC-364
PHASE - Wiring diagram ................................. EC-329
Pilot bushing replacement ................................. EM-77
Piston assembly ................................................ EM-99
Piston pin inspection .......................................... EM-95
Piston ring inspection ........................................ EM-96
Piston to bore clearance .................................... EM-99
PNP/SW - Wiring diagram ..... EC-438, AT-98, CVT-80
POS - Wiring diagram ...................................... EC-321
POWER - Wiring diagram ................... CVT-146, PG-6
Power door lock .................................................. BL-23
Power socket ................................................... WW-44
Power steering gear .......................................... PS-12
Power supply routing ........................................... PG-4
Power window .................................................. GW-17
PRE/SE - Wiring diagram .................. EC-387, EC-393
Precations for Leak detection dye .................. MTC-10
Precautions (General) .......................................... GI-4
Pressure control solenoid valve A CVT-113, CVT-118
Pressure control solenoid valve B CVT-121, CVT-124
Pressure plate - See Clutch cover ..................... CL-13
Pressure test (CVT) ......................................... CVT-45
Primary pressure sensor ............................... CVT-137
Primary Speed Sensor .................................... CVT-90
PRIPS - Wiring diagram ................................ CVT-138
PRSCVT - Wiring diagram ............................... CVT-91
PT/SEN - Wiring diagram ................................ AT-177

LU-1
ENGINE LUBRICATION SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION LU
A
LU
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 2
Precautions for Liquid Gasket .................................. 2
LIQUID GASKET APPLICATION PROCEDURE ..... 2
PREPARATION ........................................................... 3
Special Service Tools ............................................... 3
Commercial Service Tools ........................................ 3
LUBRICATION SYSTEM ............................................ 4
Lubrication Circuit .................................................... 4
ENGINE OIL ............................................................... 5
Inspection ................................................................. 5
ENGINE OIL LEVEL ............................................. 5
ENGINE OIL APPEARANCE ................................ 5ENGINE OIL LEAKAGE ........................................ 5
OIL PRESSURE CHECK ...................................... 5
Changing Engine Oil ................................................. 6
OIL FILTER ................................................................. 8
Removal and Installation .......................................... 8
REMOVAL ............................................................. 8
INSTALLATION ..................................................... 8
INSPECTION AFTER INSTALLATION .................. 8
SERVICE DATA AND SPECIFICATIONS (SDS) ........ 9
Standard and Limit .................................................... 9
OIL PRESSURE .................................................... 9
OIL CAPACITY ...................................................... 9

ENGINE OIL
LU-7
C
D
E
F
G
H
I
J
K
L
MA
LU
Revision: June 20062007 Versa
3. Loosen oil filler cap (1) and then remove drain plug (2).

Oil filter (3)

⇐ Engine front
4. Drain engine oil.
5. Install drain plug (2) with new washer. Refer to EM-24, "
Compo-
nents" .
CAUTION:
Be sure to clean drain plug (2) and install with new washer.
6. Refill with new engine oil.
Refer to MA-11, "
RECOMMENDED FLUIDS AND LUBRI-
CANTS" .
CAUTION:

The refill capacity depends on the engine oil temperature
and drain time. Use these specifications for reference
only.

Always use oil level gauge to determine the proper
amount of engine oil in the engine.
7. Warm up engine and check area around drain plug (2) and oil fil-
ter (3) for engine oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level. Refer to LU-5, "
ENGINE OIL LEVEL"
.
PBIC3915E

SERVICE DATA AND SPECIFICATIONS (SDS)
LU-9
C
D
E
F
G
H
I
J
K
L
MA
LU
Revision: June 20062007 Versa
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00T74
OIL PRESSURE
OIL CAPACITY
Unit: (US qt, Imp qt) Engine speed rpm
Approximate discharge pressure kPa (bar, kg/cm
2 , psi)
Idle speed
2,00060 (0.60, 0.61, 9)
200 (2.0, 2.0, 29)
Drain and refillWith oil filter change Approximately 3.9 (4 1/8, 3 3/8)
Without oil filter change Approximately 3.7 (3 7/8, 3 1/4)
Dry engine (engine overhaul) Approximately 4.9 (5 1/8, 4 3/8)

RECOMMENDED FLUIDS AND LUBRICANTS
MA-11
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: June 20062007 Versa
RECOMMENDED FLUIDS AND LUBRICANTSPFP:00000
Fluids and LubricantsELS001YG
*1: For further details, see “SAE Viscosity Number”.
*2: DEXRONTM III / MERCONTM , or equivalent may also be used. Outside the continental United States and Alaska contact a NISSAN
dealership for more information regarding suitable fluids, including recommended brand(s) of DEXRONTM III / MERCONTM Automatic
Transmission Fluid.
*3: Using transaxle fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the NISSAN
new vehicle limited warranty.
*4: Available in mainland U.S.A. through your NISSAN dealer.
*5: For further details, see “Air conditioner specification label”.DescriptionCapacity (Approximate)
Recommended Fluids/Lubricants
Liter US measure Imp measure
Fuel 50.0 13 1/4 gal 11 galUnleaded gasoline with an octane rating of
at least 87 AKI (RON 91)
Engine oil
Drain and refillWith oil filter
change3.9 4 1/8 qt 3 3/8 qt

API Certification Mark *2 *3

API grade SH, SJ, SL or SM, Energy
Conserving *2 *3

ILSAC grade GF-2, GF-3 & GF-4 *2 *3 Without oil fil-
ter change3.7 3 7/8 qt 3 1/4 qt
Dry engine (engine overhaul) 4.9 5 1/8 qt 4 3/8 qt
Cooling system
(with reservoir at max level)6.8 7 1/4 qt 6 qtGenuine NISSAN Long Life Anti-freeze
Coolant or equivalent
Manual transaxle fluid (MTF) 2.0 4 1/4 pt 3 1/2 ptELF XT4447 M+ 75W-80 or API GL-4, Vis-
cosity SAE 75W-80
Automatic transaxle fluid (ATF) 7.9 8 3/8 qt 7 qtGenuine NISSAN Matic “D” ATF (Conti-
nental U.S. and Alaska) or Canada NIS-
SAN Automatic Transmission Fluid *2
CVT fluid 8.3 8 3/4 qt 7 1/4 qt Genuine NISSAN CVT Fluid NS-2 *3
Brake and clutch fluid — — —Genuine NISSAN Super Heavy Duty
Brake Fluid*4 or equivalent DOT 3 (US
FMVSS No. 116)
Multi-purpose grease — — — NLGI No. 2 (Lithium soap base)
Windshield washer fluid 4.5 4 3/4 qt 4 qtGenuine NISSAN Windshield Washer
Concentrate Cleaner & Anti-Freeze or
equivalent
Air conditioning system refrigerant 0.45 ± 0.05 kg 0.99 ± 0.11 lb 0.99 ± 0.11 lb HFC-134a (R-134a) *5
Air conditioning
system oilType 1
120 m4.1 fl oz 4.2 fl ozNISSAN A/C System Lubricant Type R or
equivalent *5
Type 2
100 m3.4 fl oz 3.5 fl ozNISSAN A/C System Lubricant Type S or
equivalent *5