2006 NISSAN VERSA brake

DI-12
COMBINATION METERS
Revision: June 20062007 Versa
13 B Illumination control switch (-) — —Refer to LT-108, "ILLUMINATION
OPERATION BY LIGHTING SWITCH" .
17 GWasher fluid level switch
(Canada models)ONWasher fluid level low 0
Washer fluid level normal Battery voltage
21
BGround — — 0 22
23
24 V Fuel level sensor ground (-) ON — 0
26 BVehicle speed sensor ground
(without ABS or CVT)ON — 0
27 G Battery power supply OFF — Battery voltage
28 SB Ignition switch ON or START ON — Battery voltage
29 GR Seat belt buckle switch RH ONUnfastened (ON) 0
Fastened (OFF) Battery voltage
30 G Stop lamp switch ONBrake pedal depressed Battery voltage
Brake pedal released 0
31 V A/T N-range input (with A/T) ONTransmission gear selector lever
in N positionBattery voltage
Transmission gear selector lever
other than N position0
32 W A/T P-range input (with A/T) ONTransmission gear selector lever
in P positionBattery voltage
Transmission gear selector lever
other than P position0
33 Y A/T PN output (with A/T) ONTransmission gear selector lever
in P or N position0
Transmission gear selector lever
other than P or N positionBattery voltage
35 BREngine coolant temperature
signal outputONAt idle [after warming up, approx.
80°C (176°F)]
NOTE:
The waveforms vary depending
on engine coolant temperature.
38 L Generator ONGenerator voltage low 0
Generator voltage normal Battery voltage Te r -
minal
No.Wire
colorItemCondition
Reference value (V)
(Approx.) Ignition
switchOperation or condition
SKIB3651J

COMBINATION METERS
DI-15
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: June 20062007 Versa
DATA MONITOR
Display Item List
Display item [Unit]MAIN
SIGNALSSELECTION
FROM MENUContents
SPEED METER [km/h] X XThe value of vehicle speed signal, which is input from ABS
actuator and electric unit (control unit).
SPEED OUTPUT [km/h] X XThe value of vehicle speed signal, which is transmitted to each
unit with CAN communication.
TACHO METER [rpm] X X The value of engine speed signal, which is input from ECM.
W TEMP METER [°C] X XThe value of engine coolant temperature signal, which is input
from ECM.
FUEL METER [lit.] X XThe value, which processes a resistance signal from fuel
gauge.
DISTANCE [km] X XThe value, which is calculated by vehicle speed signal from
ABS actuator and electric unit (control unit), fuel gauge and
fuel consumption signal from ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
C-ENG W/L [ON/OFF] XIndicates [ON/OFF] condition of malfunction indicator lamp
(MIL).
AIR PRES W/L XIndicates [ON/OFF] condition of low tire pressure warning
lamp.
SEAT BELT W/L X Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high beam indicator lamp.
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of KEY warning lamp (green).
KEY R W/L [ON/OFF] X Indicates [ON/OFF] condition of KEY warning lamp (red).
KEY KNOB W/L [ON/OFF] X Indicates [ON/OFF] condition of LOCK warning lamp.
PNP P SW [ON/OFF] X X Indicates [ON/OFF] condition of inhibitor P switch.
PNP N SW [ON/OFF] X X Indicates [ON/OFF] condition of inhibitor N switch.
O/D OFF SW [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF switch.
BRAKE SW [ON/OFF] X Indicates [ON/OFF] condition of parking brake switch.
P RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift P range indi-
cator.
R RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift R range indi-
cator.
N RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift N range indi-
cator.
D RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift D range indi-
cator.
2 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 2 range indicator.
L RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of CVT shift L range indicator.
1 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 1 range indicator.
CRUISE IND [ON/OFF] X Indicates [ON/OFF] condition of CRUISE indicator.
SET IND [ON/OFF] X Indicates [ON/OFF] condition of SET indicator.
O/D OFF W/L [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF indicator lamp.

DI-16
COMBINATION METERS
Revision: June 20062007 Versa
NOTE:
Some items are not available due to vehicle specification.
*: The monitor will indicate “OFF” even though the brake warning lamp is on if either of the following conditions exist.

The parking brake is engaged

The brake fluid level is low e-4WD W/L [ON/OFF] X This item is not used for this model. “OFF” is always displayed.
EPS W/L [ON/OFF] X Indicates [ON/OFF] condition of EPS warning lamp.Display item [Unit]MAIN
SIGNALSSELECTION
FROM MENUContents

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: June 20062007 Versa DTC Confirmation Procedure ............................... 399
Diagnostic Procedure ........................................... 400
DTC P0456 EVAP CONTROL SYSTEM ................ 406
On Board Diagnosis Logic ................................... 406
DTC Confirmation Procedure ............................... 407
Overall Function Check ........................................ 408
Diagnostic Procedure ........................................... 409
DTC P0460 FUEL LEVEL SENSOR ...................... 415
Component Description ........................................ 415
On Board Diagnostic Logic .................................. 415
DTC Confirmation Procedure ............................... 415
Diagnostic Procedure ........................................... 416
Removal and Installation ...................................... 416
DTC P0461 FUEL LEVEL SENSOR ...................... 417
Component Description ........................................ 417
On Board Diagnostic Logic .................................. 417
Overall Function Check ........................................ 417
Diagnostic Procedure ........................................... 418
Removal and Installation ...................................... 418
DTC P0462, P0463 FUEL LEVEL SENSOR .......... 419
Component Description ........................................ 419
On Board Diagnostic Logic .................................. 419
DTC Confirmation Procedure ............................... 419
Diagnostic Procedure ........................................... 420
Removal and Installation ...................................... 420
DTC P0500 VSS ..................................................... 421
Description ........................................................... 421
On Board Diagnosis Logic ................................... 421
DTC Confirmation Procedure ............................... 421
Overall Function Check ........................................ 422
Diagnostic Procedure ........................................... 422
DTC P0506 ISC SYSTEM ....................................... 423
Description ........................................................... 423
On Board Diagnosis Logic ................................... 423
DTC Confirmation Procedure ............................... 423
Diagnostic Procedure ........................................... 424
DTC P0507 ISC SYSTEM ....................................... 425
Description ........................................................... 425
On Board Diagnosis Logic ................................... 425
DTC Confirmation Procedure ............................... 425
Diagnostic Procedure ........................................... 426
DTC P0605 ECM .................................................... 427
Component Description ........................................ 427
On Board Diagnosis Logic ................................... 427
DTC Confirmation Procedure ............................... 427
Diagnostic Procedure ........................................... 428
DTC P0643 SENSOR POWER SUPPLY ................ 430
On Board Diagnosis Logic ................................... 430
DTC Confirmation Procedure ............................... 430
Wiring Diagram .................................................... 431
Diagnostic Procedure ........................................... 433
DTC P0850 PNP SWITCH ...................................... 436
Component Description ........................................ 436
CONSULT-II Reference Value in Data Monitor Mode
. 436
On Board Diagnosis Logic ................................... 436
DTC Confirmation Procedure ............................... 436
Overall Function Check ........................................ 437Wiring Diagram .....................................................438
Diagnostic Procedure ...........................................439
DTC P1148 CLOSED LOOP CONTROL ................442
On Board Diagnosis Logic ....................................442
DTC P1217 ENGINE OVER TEMPERATURE ........443
System Description ...............................................443
CONSULT-II Reference Value in Data Monitor Mode
.444
On Board Diagnosis Logic ....................................445
Overall Function Check ........................................445
Wiring Diagram .....................................................448
Diagnostic Procedure ...........................................450
Main 13 Causes of Overheating ...........................458
Component Inspection ..........................................459
DTC P1225 TP SENSOR ........................................460
Component Description ........................................460
On Board Diagnosis Logic ....................................460
DTC Confirmation Procedure ...............................460
Diagnostic Procedure ...........................................461
Removal and Installation ......................................461
DTC P1226 TP SENSOR ........................................462
Component Description ........................................462
On Board Diagnosis Logic ....................................462
DTC Confirmation Procedure ...............................462
Diagnostic Procedure ...........................................463
Removal and Installation ......................................463
DTC P1421 COLD START CONTROL ...................464
Description ............................................................464
On Board Diagnosis Logic ....................................464
DTC Confirmation Procedure ...............................464
Diagnostic Procedure ...........................................464
DTC P1564 ASCD STEERING SWITCH ................466
Component Description ........................................466
CONSULT-II Reference Value in Data Monitor Mode
.466
On Board Diagnosis Logic ....................................466
DTC Confirmation Procedure ...............................467
Wiring Diagram .....................................................468
Diagnostic Procedure ...........................................469
Component Inspection ..........................................472
DTC P1572 ASCD BRAKE SWITCH ......................473
Component Description ........................................473
CONSULT-II Reference Value in Data Monitor Mode
.473
On Board Diagnosis Logic ....................................473
DTC Confirmation Procedure ...............................474
Wiring Diagram .....................................................475
Diagnostic Procedure ...........................................476
Component Inspection ..........................................481
DTC P1574 ASCD VEHICLE SPEED SENSOR .....483
Component Description ........................................483
On Board Diagnosis Logic ....................................483
DTC Confirmation Procedure ...............................483
Diagnostic Procedure ...........................................484
DTC P1715 INPUT SPEED SENSOR (TURBINE
REVOLUTION SENSOR) ........................................485
Description ............................................................485
CONSULT-II Reference Value in Data Monitor Mode
.485

EC-6Revision: June 20062007 Versa On Board Diagnosis Logic ....................................485
Diagnostic Procedure ...........................................485
DTC P1715 INPUT SPEED SENSOR (PRIMARY
SPEED SENSOR) ...................................................486
Description ............................................................486
CONSULT-II Reference Value in Data Monitor Mode
.486
On Board Diagnosis Logic ....................................486
DTC Confirmation Procedure ...............................486
Diagnostic Procedure ...........................................487
DTC P1805 BRAKE SWITCH .................................488
Description ............................................................488
CONSULT-II Reference Value in Data Monitor Mode
.488
On Board Diagnosis Logic ....................................488
DTC Confirmation Procedure ...............................488
Wiring Diagram .....................................................489
Diagnostic Procedure ...........................................490
Component Inspection ..........................................492
DTC P2100, P2103 THROTTLE CONTROL MOTOR
RELAY .....................................................................493
Component Description ........................................493
CONSULT-II Reference Value in Data Monitor Mode
.493
On Board Diagnosis Logic ....................................493
DTC Confirmation Procedure ...............................493
Wiring Diagram .....................................................495
Diagnostic Procedure ...........................................496
DTC P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ..............................................................499
Description ............................................................499
On Board Diagnosis Logic ....................................499
DTC Confirmation Procedure ...............................499
Wiring Diagram .....................................................500
Diagnostic Procedure ...........................................501
Component Inspection ..........................................505
Removal and Installation ......................................505
DTC P2118 THROTTLE CONTROL MOTOR .........506
Component Description ........................................506
On Board Diagnosis Logic ....................................506
DTC Confirmation Procedure ...............................506
Wiring Diagram .....................................................507
Diagnostic Procedure ...........................................508
Component Inspection ..........................................509
Removal and Installation ......................................510
DTC P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR .............................................................511
Component Description ........................................511
On Board Diagnosis Logic ....................................511
DTC Confirmation Procedure ...............................511
Diagnostic Procedure ...........................................512
DTC P2122, P2123 APP SENSOR .........................513
Component Description ........................................513
CONSULT-II Reference Value in Data Monitor Mode
.513
On Board Diagnosis Logic ....................................513
DTC Confirmation Procedure ...............................514
Wiring Diagram .....................................................515
Diagnostic Procedure ...........................................516Component Inspection .......................................... 518
Removal and Installation ....................................... 518
DTC P2127, P2128 APP SENSOR ......................... 519
Component Description ........................................ 519
CONSULT-II Reference Value in Data Monitor Mode
. 519
On Board Diagnosis Logic .................................... 519
DTC Confirmation Procedure ................................ 520
Wiring Diagram ..................................................... 521
Diagnostic Procedure ............................................ 523
Component Inspection .......................................... 525
Removal and Installation ....................................... 525
DTC P2135 TP SENSOR ........................................ 526
Component Description ........................................ 526
CONSULT-II Reference Value in Data Monitor Mode
. 526
On Board Diagnosis Logic .................................... 526
DTC Confirmation Procedure ................................ 527
Wiring Diagram ..................................................... 528
Diagnostic Procedure ............................................ 529
Component Inspection .......................................... 531
Removal and Installation ....................................... 531
DTC P2138 APP SENSOR ...................................... 532
Component Description ........................................ 532
CONSULT-II Reference Value in Data Monitor Mode
. 532
On Board Diagnosis Logic .................................... 532
DTC Confirmation Procedure ................................ 533
Wiring Diagram ..................................................... 534
Diagnostic Procedure ............................................ 536
Component Inspection .......................................... 539
Removal and Installation ....................................... 539
DTC P2A00 A/F SENSOR 1 .................................... 540
Component Description ........................................ 540
CONSULT-II Reference Value in Data Monitor Mode
. 540
On Board Diagnosis Logic .................................... 540
DTC Confirmation Procedure ................................ 541
Wiring Diagram ..................................................... 542
Diagnostic Procedure ............................................ 543
Removal and Installation ....................................... 548
ASCD BRAKE SWITCH .......................................... 549
Component Description ........................................ 549
CONSULT-II Reference Value in Data Monitor Mode
. 549
Wiring Diagram ..................................................... 550
Diagnostic Procedure ............................................ 552
Component Inspection .......................................... 557
ASCD INDICATOR .................................................. 559
Component Description ........................................ 559
CONSULT-II Reference Value in Data Monitor Mode
. 559
Wiring Diagram ..................................................... 560
Diagnostic Procedure ............................................ 561
ELECTRICAL LOAD SIGNAL ................................ 562
CONSULT-II Reference Value in Data Monitor Mode
. 562
Diagnostic Procedure ............................................ 562
FUEL INJECTOR ..................................................... 564

EC-10Revision: June 2006
INDEX FOR DTC
2007 Versa
P0733 0733 A/T 3RD GR FNCTNAT- 1 2 4
P0734 0734 A/T 4TH GR FNCTNAT- 1 2 8
P0740 0740 TCC SOLENOID/CIRCAT- 1 3 4
P0744 0744 A/T TCC S/V FNCTNAT- 1 3 9 (A/T),
CVT-110
(CVT)
P0745 0745 L/PRESS SOL/CIRCAT- 1 4 5
P0746 0746 PRS CNT SOL/A FCTNCVT-118
P0750 0750 SFT SOL A/CIRCAT- 1 5 1
P0755 0755 SFT SOL B/CIRCAT- 1 5 6
P0776 0776 PRS CNT SOL/B FCTNCVT-121
P0778 0778 PRS CNT SOL/B CIRCCVT-124
P0840 0840 TR PRS SENS/A CIRCCVT-129
P0845 0845 TR PRS SENS/B CIRCCVT-137
P0850 0850 P-N POS SW/CIRCUITEC-436
P1148 1148 CLOSED LOOP-B1EC-442
P1217 1217 ENG OVER TEMPEC-443
P1225 1225 CTP LEARNINGEC-460
P1226 1226 CTP LEARNINGEC-462
P1421 1421 COLD START CONTROLEC-464
P1564 1564 ASCD SWEC-466
P1572 1572 ASCD BRAKE SWEC-473
P1574 1574 ASCD VHL SPD SENEC-483
P1610 - P1615 1610 - 1615 NATS MALFUNCTIONBL-212
P1705 1705 TP SEN/CIRC CVTCVT-150
P1715 1715 IN PULY SPEEDEC-485 (A/T),
EC-486
(CVT)
P1740 1740 LU-SLCT SOL/CIRCCVT-158
P1760 1760 O/R CLTCH SOL/CIRCAT- 1 6 1
P1777 1777 STEP MOTR CIRCCVT-164
P1778 1778 STEP MOTR FNCCVT-168
P1805 1805 BRAKE SW/CIRCUITEC-488
P2100 2100 ETC MOT PWREC-493
P2101 2101 ETC FUNCTION/CIRCEC-499
P2103 2103 ETC MOT PWREC-493
P 2 11 8 2 11 8 E T C M O TEC-506
P 2 11 9 2 11 9 E T C A C T REC-511
P2122 2122 APP SEN 1/CIRCEC-513
P2123 2123 APP SEN 1/CIRCEC-513
P2127 2127 APP SEN 2/CIRCEC-519
P2128 2128 APP SEN 2/CIRCEC-519
P2135 2135 TP SENSOREC-526
P2138 2138 APP SENSOREC-532
P2A00 2A00 A/F SENSOR1 (B1)EC-540
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3

EC-12Revision: June 2006
INDEX FOR DTC
2007 Versa
Alphabetical IndexUBS00QB2
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-151, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-154, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SENSOR1 (B1) P0130 0130EC-220
A/F SENSOR1 (B1) P0131 0131EC-227
A/F SENSOR1 (B1) P0132 0132EC-233
A/F SENSOR1 (B1) P0133 0133EC-239
A/F SENSOR1 (B1) P2A00 2A00EC-540
A/F SEN1 HTR (B1) P0031 0031EC-161
A/F SEN1 HTR (B1) P0032 0032EC-161
A/T 1ST GR FNCTN P0731 0731AT- 11 7
A/T 2ND GR FNCTN P0732 0732AT-121
A/T 3RD GR FNCTN P0733 0733AT-124
A/T 4TH GR FNCTN P0734 0734AT-128
A/T TCC S/V FNCTN P0744 0744AT-139 (A/T),
CVT-110
(CVT)
APP SEN 1/CIRC P2122 2122EC-513
APP SEN 1/CIRC P2123 2123EC-513
APP SEN 2/CIRC P2127 2127EC-519
APP SEN 2/CIRC P2128 2128EC-519
APP SENSOR P2138 2138EC-532
ASCD BRAKE SW P1572 1572EC-473
ASCD SW P1564 1564EC-466
ASCD VHL SPD SEN P1574 1574EC-483
ATF TEMP SEN/CIRC P0710 0710AT-102 (A/T),
CVT-85
(CVT)
BRAKE SW/CIRCUIT P1805 1805EC-488
CAN COMM CIRCUIT U1000
1000*4EC-151
CAN COMM CIRCUIT U1001
1001*4EC-151
CKP SEN/CIRCUIT P0335 0335EC-319
CLOSED LOOP-B1 P1148 1148EC-442
CMP SEN/CIRC-B1 P0340 0340EC-327
COLD START CONTROL P1421 1421EC-464
CONTROL UNIT(CAN) U1010 1010EC-154
CTP LEARNING P1225 1225EC-460
CTP LEARNING P1226 1226EC-462
CYL 1 MISFIRE P0301 0301EC-308
CYL 2 MISFIRE P0302 0302EC-308
CYL 3 MISFIRE P0303 0303EC-308
CYL 4 MISFIRE P0304 0304EC-308

EC-28Revision: June 2006
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
2007 Versa
AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
System DescriptionUBS00QB6
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line.
BASIC ASCD SYSTEM
Refer to Owner's Manual for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated by CRUISE indicator and SET indicator in combination meter. If any
malfunction occurs in ASCD system, it automatically deactivates control.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (The CRUISE indicator in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET indicator in combination meter illuminates.)
ACCELERATE OPERATION
If the RESUME/ACCELERATE switch is depressed during cruise control driving, increase the vehicle speed
until the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.

CANCEL switch is pressed

More than two switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)

Brake pedal is depressed

Clutch pedal is depressed or gear position is changed to the neutral position (M/T models)

Selector lever is changed to N, P, R position (A/T and CVT models)

Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.

Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will
stop blinking and the cruise operation will be able to work by pressing SET/COAST switch or RESUME/
ACCELERATE switch.

Malfunction for some self-diagnoses regarding ASCD control: SET lamp will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
Sensor Input signal to ECM ECM function Actuator
ASCD brake switch Brake pedal operation
ASCD vehicle speed controlElectric throttle control
actuator Stop lamp switch Brake pedal operation
ASCD clutch switch (M/T models) Clutch pedal operation
ASCD steering switch ASCD steering switch operation
Park/neutral position (PNP) switch Gear position
Combination meter Vehicle speed*
TCM (A/T and CVT models) Powertrain revolution*