2006 DODGE RAM SRT-10 ignition

5.ECM
Turn the ignition off.
Disconnect the Fan harness connector.
Turn the ignition on.
Measure the voltage between the sensor (K668) #2 5-volt supply (fan
speed sensor power) circuit at the fan clutch harness connector and the
fan speed sensor ground.
Is the voltage between 4.5 and 5.5 volts?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

3.ECM
Turn the ignition off.
Reconnect the ECM harness connectors.
Turn the ignition on.
Measure the voltage between the (K668) 5-volt supply circuit in the sen-
sor harness connector and battery negative.
Is the voltage greater than 6 volts?
Ye s>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)

When Monitored:
When the ignition is on.
Set Condition:
When the signal from the A/C Clutch circuit output does not match the signalfrom the A/C Clutch feedback
Possible Causes
LOW VOLTAGE SUPPLY TO THE TIPM
A/C CLUTCH CIRCUIT OPEN
A/C CLUTCH CIRCUIT SHORTED TO GROUND
TIPM
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.TIPM GROUND OPEN
Ignition on, engine not running.
Using a voltmeter, connect one voltmeter lead to Battery Positive and the other on TIPM ground.
Does the voltmeter show battery voltage?
Ye s>>
Go To 2
No>>
Fix or replace the open circuit in the Battery Return Circuit
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
2.LOOSE CONNECTION
Disconnect the ECM and TIPM connectors.
NOTE: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance of the A/C Clutch signal wire between the TIPM and the ECM con-
nector..
Is the resistance less than 10 Ohms?
No>>
Fix or replace the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
Ye s>>
Go To 3
3.A/C CLUTCH CIRCUIT OPEN
Turn the ignition off.
Using an Ohmmeter, measure the resistance of the A/C Clutch signal wire between the TIPM connector and battery
negative.
Is the resistance greater than 100k Ohms?
Ye s>>
Go To 4
No>>
Fix or replace the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

4.FUSED BATTERY SUPPLY
Connect the ECM and TIPM connectors.
Ignition on, engine not running.
Using a back probing tool 6801, back probe the A/C clutch logic pin in the TIPM logic connector.
Usinga12volttestlightconnectedtobatterypositive,checkthetransmission logic circuit at the TIPM connector
while actuating the A/C clutch circuit with the Electronic Service Tool.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light illuminate brightly?
Ye s>>
Go To 5
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
5.TIPM
Using a back probing tool, back probe the A/C clutch power pin from the TIPM power connector.
Using a 12 volt test light connected to battery positive, check the transmission power circuit at the TIPM connector
while actuating the A/C clutch circuit with the Electronic Service Tool.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light illuminate brightly?
Ye s>>
Te s t c o m p l e t e .
Perform Intermittent Condition test. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)
No>>
Replace the TIPM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

When Monitored:
When the ignition is on.
Set Condition:
When the signal from the A/C Clutch output does not match the signal from theA/C Clutch feedback.
Possible Causes
WIRING HARNESS OR CONNECTIONS
A/C CLUTCH CIRCUIT SHORTED TO EXTERNAL VOLTAGE
TIPM
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.A/C CLUTCH CIRCUIT SHORTED TO EXTERNAL VOLTAGE
Ignition off.
Disconnect the ECM and TIPM connectors.
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Using a Voltmeter, measure the voltage of the A/C Clutch Control Circuit between the TIPM connector and battery
negative..
Is the voltage less than 1 volt?
Ye s>>
Go To 2
Ye s>>
Repair or Replace the wiring harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
2.ECM
Ignition off.
Connect the ECM and TIPM connectors.
Ignition on, engine not running.
Using a back probing tool 6801, back probe the A/C clutch control circuit inthe TIPM connector.
Using a 12 volt test light connected to battery positive, check the transmission control circuit at the TIPM connector
while actuating the A/C clutch circuit with the Electronic Service Tool.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light illuminate brightly?
Ye s>>
Go To 3
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

When Monitored:
With the key on.
Set Condition:
Voltage detected on the sensor supply is below a calibrated value.
Possible Causes
ECM
(F855) #1 5-VOLT SUPPLY SHORTED TO GROUND
(F855) #1 5-VOLT SUPPLY SHORTED
FUEL RAIL PRESSURE
A/C PRESSURE SENSOR
MAP SENSOR
CAMSHAFT POSITION SENSOR
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.ECM
Turn the ignition off.
Disconnect the ECM 60 pin harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage between the Sensor (F855) #1 5-volt Supply and
the Sensor (K916) #1 Return pin at the ECM.
Is the voltage between 4.5 and 5.5 volts?
Ye s>>
Go To 2
No>>
Replace and program the ECM in accordance with the Ser-
vice Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

When Monitored:
While the engine is running.
Set Condition:
Voltage detected on the sensor supply is above a calibrated value.
Possible Causes
ECM
(F855) 5-VOLT SUPPLY SHORTED TO VOLTAGE
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.ECM
Turn the ignition off.
Disconnect the ECM 60 pin harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage between the Sensor (F855) #1 5-volt Supply and
theSensor#1ReturnpinattheECM.
Is the voltage between 4.5 and 5.5 volts?
Ye s>>
Go To 2
No>>
Replace and program the ECM in accordance with the Ser-
vice Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

2.(F855) 5-VOLT SUPPLY SHORTED TO VOLTAGE
Key off.
Disconnect the sensor connectors for each pressure sensor, and the
engine position sensor.
Disconnect the ECM 50 way harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine off.
Measure the voltage between the supply circuit at each pressure sensor
harness connector and battery negative.
Measure voltage between the (F853) 5-volt supply circuit at the engine
position sensor harness connector and battery negative.
Is the voltage less than 1 volt?
Ye s>>
Go To 3
No>>
Repair the (F855) 5-volt supply shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
3.SENSOR SUPPLY SHORTED TO VOLTAGE IN HARNESS
Measure the resistance between the #1 sensor supply circuit and all
other circuit in the ECM connectors.
Is the resistance less than 10 ohms?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
Repair the harness shorted to voltage.