2006 DODGE RAM SRT-10 diagram

P0646-LOW VOLTAGE DETECTED AT THE A/C CLUTCH RELAY
For a complete wiring diagramRefer to Section 8W.

P0647-HIGH VOLTAGE DETECTED AT THE A/C CLUTCH RELAY
For a complete wiring diagramRefer to Section 8W.

P0652-LOW VOLTAGE AT THE #1 SENSOR SUPPLY CIRCUIT
For a complete wiring diagramRefer to Section 8W.

P0653-HIGH VOLTAGE AT THE #1 SENSOR SUPPLY CIRCUIT
For a complete wiring diagramRefer to Section 8W.

For a complete wiring diagramRefer to Section 8W.
When Monitored:
With engine running.
Set Condition:
Low voltage detected at the APPS supply circuit or low voltage detected at the APPS 1 5–volt supply.
Possible Causes
(F855) APPS 5-VOLT SUPPLY OPEN
APPS HIGH RESISTANCE
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO (K922) RETURN CIRCUIT
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO BATTERY NEGATIVE
ECM
INTERMITTENT CONDITION
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO OTHER CIRCUITS
APPS
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
1.(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO BATTERY NEGATIVE
Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the APPS harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the APPS1 (F855) 5-volt supply circuit
between the sensor harness connector and battery negative
Is the resistance greater than 100 k ohms?
Ye s>>
Go To 2
No>>
Repair the (F855) 5-volt supply circuit shorted to battery
negative.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

For a complete wiring diagramRefer to Section 8W.
When Monitored:
Whileengineisrunning.
Set Condition:
High voltage detected at the APPS supply circuit.
Possible Causes
(F855) 5-VOLT SUPPLY OPEN
(F855) 5-VOLT SUPPLY SHORT TO VOLTAGE
ECM
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
1.(F855) 5-VOLT SUPPLY OPEN
Turn the ignition off.
Disconnect the APPS harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage between the (F855) APPS #1 5-volt supply circuit
at the sensor connector and battery negative.
Is the voltage between 4.5 and 5.5 volts?
Ye s>>
Replace the APPS.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Go To 2
2.(F855) 5-VOLT SUPPLY SHORT TO VOLTAGE
Turn the ignition off.
Disconnect the ECM harness connector(s).
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage between the (F855) APPS #1 5-volt supply circuit
in the sensor harness connector and battery negative.
Is the voltage less than 1 volt?
Ye s>>
Go To 3
No>>
Repair or replace the wiring harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

P1272-A/C CLUTCH CONTROL CIRCUIT 2 LOW
For a complete wiring diagramRefer to Section 8W.

P1273-A/C CLUTCH CONTROL CIRCUIT 2 HIGH
For a complete wiring diagramRefer to Section 8W.