2006 DODGE RAM SRT-10 battery

4.SIGNAL CIRCUIT SHORTED TO BATTERY NEGATIVE
Disconnect the ECM harness connector(s).
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between the signal circuit of the intake air heaterrelay and battery negative.
Is the resistance greater than 100 K ohms?
Ye s>>
Go To 5
No>>
Repair signal circuit shorted to battery negative.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
5.SIGNAL CIRCUIT SHORTED TO OTHER CIRCUITS
Measure the resistance between the signal circuit of the intake air heaterrelay and all other circuits in the ECM
harness connector.
Is the resistance greater than 100 K ohms?
Ye s>>
Go To 6
No>>
Repair signal circuit shorted to other circuits.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
6.ECM
Reconnect the ECM harness connectors.
Turn the ignition on.
Disconnect the intake air heater relay signal wire.
Did DTC P0542 or 2608 set?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diagnostic Procedure). (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

P0562-BATTERY VOLTAGE LOW
For a complete wiring diagramRefer to Section 8W.

When Monitored:
With the key on or the engine running.
Set Condition:
The battery voltage detected by the ECM is less than a calibrated value.
Possible Causes
P0622 PRESENT
P2502 PRESENT
P2503 PRESENT
BATTERY TERMINAL CONNECTIONS
ACCESSORY WIRING
BATTERY
HIGH RESISTANCE IN WIRE HARNESS
ECM
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.P0622 PRESENT
With the scan tool, read DTCs.
Is P0622 set?
Ye s>>
Repair P0622 first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 2
2.P2502 PRESENT
With the scan tool, read DTCs.
Is P2502 set?
Ye s>>
Repair P2502 first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 3
3.P2503 PRESENT
With the scan tool, read DTCs.
Is P2503 set?
Ye s>>
Repair P2503 first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 4

4.BATTERY TERMINAL CONNECTIONS
Visually inspect the positive and negative connections at the batteries and inspect the battery negative connections
at the engine block.
Are the connections free of corrosion and are they tight?
Ye s>>
Go To 5
No>>
Repair the poor connections.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
5.ACCESSORY WIRING
Check for add-on or accessory wiring at positive (+) terminal of the battery
Are there any damaged wires at the battery?
Ye s>>
Repair accessory wiring.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 6
6.BATTERY(S)
Perform battery load test using the Midtronics Micro 420 battery system tester.
Did the battery(s) pass the test?
Ye s>>
Go To 7
No>>
Replace the weak battery or batteries.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
7.HIGH RESISTANCE IN WIRE HARNESS
Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the battery terminals.
Measure the resistance from the positive and negative battery posts to
the appropriate circuits in the ECM harness connector
Is the resistance less than 10 Ohms?
Ye s>>
Go To 8
No>>
Repair the high resistance in the wire harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

8.ECM
Reconnect the battery terminals.
Measure and record the voltage between battery positive pins of the
ECM connector and the battery negative circuits of the ECM harness
connector.
Reconnect the ECM harness connectors.
Use the scan tool to measure and record battery voltage.
Are the readings within 3 volts of each other?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

P0563-BATTERY VOLTAGE HIGH
For a complete wiring diagramRefer to Section 8W.

When Monitored:
With the key on or the engine running.
Set Condition:
The battery voltage detected by the ECM is greater than a calibrated value.
Possible Causes
P0622 PRESENT
P2502 PRESENT
P2504 PRESENT
BATTERIES IMPROPERLY INSTALLED
ECM
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.P0622 PRESENT
With the scan tool, read DTCs.
Is P0622 set?
Ye s>>
Repair P0622 first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 2
2.P2502 PRESENT
With the scan tool, read DTCs.
Is P2502 set?
Ye s>>
Repair P2502 first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 3
3.P2504 PRESENT
With the scan tool, read DTCs.
Is P2504 set?
Ye s>>
Repair P2504 first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 4

4.BATTERIES IMPROPERLY INSTALLED
Disconnect the ECM harness connectors.
Measure the battery voltage between the positive circuits and ground of
the ECM harness connector.
Is the voltage less than 19 volts?
Ye s>>
Go To 5
No>>
Install the battery system correctly.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
5.ECM
Reconnect the battery terminals.
Measure and record the voltage between battery positive pins of the
ECM connector and the battery negative circuits of the ECM harness
connector.
Reconnect the ECM harness connectors.
Use the scan tool to measure and record battery voltage.
Are the readings within 3 volts of each other?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)