2006 ACURA CSX torque



(#'
 ) M/T model
A/T model
5-355-35
Side Engine Mount Bracket
Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
7. Raise the vehicle on the lift.
8. M/T model: Tighten the front mount mounting bolt.
9. Install the splash shield (see step 40 on page 5-20).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
(cont’d)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:08 61SNR030_050_0035
ProCarManuals.com
DYNOMITE -2009-



(#'
 ) M/T model
A/T model
5-355-35
Side Engine Mount Bracket
Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
7. Raise the vehicle on the lift.
8. M/T model: Tighten the front mount mounting bolt.
9. Install the splash shield (see step 40 on page 5-20).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
(cont’d)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:08 61SNR030_050_0035
ProCarManuals.com
DYNOMITE -2009-



5-37
A
A 12x1.25mm
72 N·m
(7.3 kgf·m, 52 lbf·ft)
14x1.5mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
8. Raise the vehicle on the lift.
9. Remove the splash shield (see step 25 on page 5-5).
10. Loosen the lower torque rod mounting bolt (A).
11. M/T model: Loosen the front mount mounting bolt (A). 12. Lower the vehicle on the lift.
13. Tighten the side engine mount mounting bolts and
nut.
(cont’d)
08/08/21 14:21:09 61SNR030_050_0037
ProCarManuals.com
DYNOMITE -2009-





M/T model
A/T model
5-38 Engine Assembly
Side Engine Mount Bracket Replacement (cont’d)
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft) 14x1.5mm
93 N·m
(9.5 kgf·m, 69 lbf·ft)
14. Tighten the transmission mounting bolt and nuts. 15. Raise the vehicle on the lift.
16. Tighten the lower torque rod mounting bolt.
17. Lower the vehicle on the lift.
18. Install the air cleaner assembly (see page 11-345).
08/08/21 14:21:10 61SNR030_050_0038
ProCarManuals.com
DYNOMITE -2009-






M/T model
A/T model
5-39
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft) 12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
19. Install the upper torque rod, then tighten the new
upper torque rod mounting bolts in the numbered
sequence shown. 20. Raise the vehicle on the lift.
21. M/T model: Tighten the front mount mounting bolt.
22. Install the splash shield (see step 40 on page 5-20).
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:10 61SNR030_050_0039
ProCarManuals.com
DYNOMITE -2009-



(#'

")
6-11
VTC Actuator Inspection
A B
1. Remove the cam chain (see page 6-18).
2. Loosen the rocker arm adjusting screws: K20Z2 engine (see step 2 on page 6-43)
 K20Z3 engine (see step 2 on page 6-44)
3. Remove the camshaft holder:  K20Z2 engine (see step 3 on page 6-43)
 K20Z3 engine (see step 3 on page 6-44)
4. Remove the intake camshaft.
5. Check that the variable valve timing control (VTC) actuator is locked by turning the VTC actuator
counterclockwise. If not locked, turn the VTC
actuator clockwise until it stops, then recheck it. If it
is still not locked, replace the VTC actuator.
6. Seal the advance holes (A) and the retard holes (B) in the No. 1 camshaft journal with tape.
7. Punch a hole in the tape over one of the advance holes.
8. Apply air to the advance hole to release the lock. 9. Check that the VTC actuator moves smoothly. If the
VTC actuator does not move smoothly, replace the
VTC actuator.
10. Remove the tape and adhesive residue from the No. 1 camshaft journal.
11. Make sure the punch marks on the VTC actuator and the exhaust camshaft sprocket are facing up,
then set the camshafts in the rocker shaft holder:
 K20Z2 engine (see step 6 on page 6-61)
 K20Z3 engine (see step 6 on page 6-62)
12. Set the camshaft holders and cam chain guide B in place:
 K20Z2 engine (see step 7 on page 6-61)
 K20Z3 engine (see step 7 on page 6-62)
13. Tighten the camshaft holder bolts to the specified torque:
 K20Z2 engine (see step 8 on page 6-61)
 K20Z3 engine (see step 8 on page 6-62)
14. Hold the camshaft, and turn the VTC actuator clockwise until you hear it click. Make sure to lock
the VTC actuator by turning it.
15. Install the cam chain (see page 6-21).
16. Adjust the valve clearance:  K20Z2 engine (see page 6-12)
 K20Z3 engine (see page 6-14)
08/08/21 14:26:29 61SNR030_060_0011
ProCarManuals.com
DYNOMITE -2009-



Specified Torque
Intake:
7x0.75mm
20 N·m (2.0 kgf·m, 14 lbf·ft)
Apply new engine oil to the nut threads.
Exhaust:
7x0.75mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
Apply new engine oil to the nut threads.
6-13
07MAA-PR70110
07MAA-PR70120
5. If you feel too much or too little drag, loosen the locknut with the locknut wrench and the adjuster,
andturntheadjustingscrewuntilthedragonthe
feeler gauge is correct.
6. Tighten the locknut to the specified torque, and recheck the clearance. Repeat the adjustment if
necessary. 7. Rotate the crankshaft 180 ° clockwise (camshaft
pulley turns 90 °).
8. Check and, if necessary, adjust the valve clearance on the No. 3 cylinder.
9. Rotate the crankshaft 180 ° clockwise (camshaft pulley turns 90 °).
10. Check and, if necessary, adjust the valve clearance on the No. 4 cylinder.
(cont’d)
08/08/21 14:26:30 61SNR030_060_0013
ProCarManuals.com
DYNOMITE -2009-




µµ
µµ
Valve Clearance
Intake: 0.21 0.25 mm (0.008 0.010 in.)
Exhaust: 0.25 0.29 mm (0.010 0.011 in.)
Specified Torque
7x0.75mm
20 N·m (2.0 kgf·m, 14 lbf·ft)
Apply new engine oil to the nut threads.
6-15
No. 1No. 2 No. 3 No. 4
No. 1 No. 2
No. 3 No. 4
EXHAUST
INTAKE
AB 07MAA-PR70110
07MAA-PR70120
3. Select the correct feeler gauge for the valve clearance you are going to check.
4. Insert the feeler gauge (A) between the adjusting screw (B) and the end of the valve stem, then slide
it back and forth, you should feel a slight amount of
drag. 5. If you feel too much or too little drag, loosen the
locknut with the locknut wrench and the adjuster,
andturntheadjustingscrewuntilthedragonthe
feeler gauge is correct.
6. Tighten the locknut to specified torque, and recheck the clearance. Repeat the adjustment if necessary.
7. Rotate the crankshaft 180 ° clockwise (camshaft pulley turns 90 °).
8. Check and, if necessary, adjust the valve clearance on the No. 3 cylinder.
(cont’d)
08/08/21 14:26:31 61SNR030_060_0015
ProCarManuals.com
DYNOMITE -2009-