2006 ACURA CSX brake



(#'
 )
For Some Models
20-169
Trunk Lid Spoiler Replacement
:Nut,2 :Bolt,2
Fastener Locations
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft) B
C
B A
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the trunk lid.
1. Open the trunk lid, and remove the nut and bolts from inside the trunk lid. 2. Close the trunk lid. While lifting the trunk lid spoiler
(A) up, disconnect the high mount brake light
terminals (B) from the spoiler subharness (C), then
remove the spoiler.
3. Install the spoiler in the reverse order of removal, and make sure the high mount brake light terminals
are plugged in properly.
08/08/21 15:05:05 61SNR030_200_0171
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
21-81
Heater Unit/Core Replacement
A
B C
8x1.25mm
12.3 N·m
(1.3 kgf·m, 9.0 lbf·ft)
B A
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
1. Do the battery terminal disconnection procedure (see page 22-68).
2. Disconnect the A/C line from the evaporator core
(see page 21-78).
3. Remove the air cleaner housing assembly (see page 11-345).
4. When the engine is cool, drain the engine coolant from the radiator (see page 10-8).
5. From under the hood, slide the hose clamps (A) back. Disconnect the inlet heater hose (B) and the
outlet heater hose (C) from the heater unit. Note the
orientation of the hoses.
Engine coolant will run out when the hoses are
disconnected; drain it into a clean drip pan. Be sure
not to let coolant spill on the electrical parts or the
painted surfaces. If any coolant spills, rinse it off
immediately. 6. Remove the mounting nut from the heater unit.
Take care not to damage or bend the fuel lines or
brake lines, etc.
7. Remove the dashboard (see page 20- 108).
8. Disconnect the connector (A) from the blower motor. Remove the wire harness clip (B).
(cont’d)
08/08/21 14:43:43 61SNR030_210_0082
ProCarManuals.com
DYNOMITE -2009-

(#'

")
21-97
A/C System Noise Check
 Air conditioning refrigerant or lubricant vaporcan irritate your eyes, nose, or throat.
 Be careful when connecting service equipment.
 Do not breathe refrigerant or vapor.
The A/C system noise check will help you determine the
source of abnormal A/C system noise.
NOTE:  If accidental system discharge occurs, ventilate the work area before resuming service.
 Additional health and safety information may be obtained from the refrigerant and lubricant
manufacturers.
 Identify the conditions when the noise occurs. The weather, the vehicle speed, the vehicle being in gear
or in neutral, the engine temperature, or other
conditions may be factors in determining the noise
source.
 Do an A/C system inspection (see page 21-6), and correct any problems found prior to diagnosing
abnormal noises.
 Abnormal A/C noises can be misleading. For example,
a sound similar to a failed bearing may be caused by
loose fasteners, loose mounting brackets, or faulty
compressor clutch assembly.
1. Inspect the air inlet grille in the cowl cover for debris. If debris is present, remove it.
2. Sit inside the vehicle, close the doors and windows, and turn the ignition switch to ON (II), but do not
start the engine. Cycle the HVAC system through all
blower speeds and all air distribution modes to
determine where and when the noise occurs. 3. Operate the blower at each speed with the engine
and A/C off, and check for unusual noises and
excessive vibration. If noise and/or vibration are
present, do the following checks:
–1 If the noise or vibration occurs only in a specific mode or setting, then check these
items: Operation of the mode control motor, door, and linkage
 Operation of the air mix control motor(s), door(s), and linkage
 Operation of the recirculation motor, door, and linkage
–2 If there is a squeaking or chirping noise, but no unusual vibration, replace the blower motor
(see page 21-77).
–3 Remove the blower unit (see page 21-76), and check for foreign material (leaves or twigs, for
example) on the blower motor and fan. If
foreign material is present, remove it, and
recheck for noise. If you don’t find any foreign
material, remove the blower motor (see page
21-77), and check these items: Check if the fan blades are cracked or broken
 Make sure the fan retainer is tight
 Inspect the fan alignment on the blower motor shaft
Replace the blower motor if any problems are
present.
4. Set up the vehicle for the running A/C che cks:
 Select a quiet area for testing
 Apply the parking brake
 Shift the vehicle in PARK or in Neutral
 Start the engine
 Set the temperature control dial to Max Cool
 Set the mode control switch to Vent
 Set the fan control dial to minimum (but not OFF)
 Turn the A/C switch ON
Switch the compressor on and off several times to
clearly identify the sound during A/C compressor
operation. Listen to the noise while the A/C
compressor clutch is engaged and disengaged.
Probe the A/C system with a stethoscope to
pinpoint the noise.
NOTE: If the noise does not change when the A/C
compressor clutch engages or disengages, the
noise may be caused by an engine-related
component. Probe the engine area with a
stethoscope to pinpoint the noise. (cont’d)
08/08/21 14:44:54 61SNR030_210_0098
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Body Electrical
Body Electrical..................................
..................................
Relay and Control Unit
Locations . 22-7
................
Connectors and Harnesses . 22-13
........................
........................
Fuse/Relay Boxes . 22-58
......................
......................
Power Distribution . 22-60
....................
....................
Ground Distribution . 22-64
Under-hood Fuse/Relay Box
Under-dash Fuse/Relay Box
Battery
Relays
Ignition Switch
Multiplex Integrated Control System Keyless/Power Door Locks/Security
System
Horns
Exterior Lights
Turn Signal/Hazard Warning Lights
Interior Lights.............................................. .....
..............................................
.....
Special Tools . 22-2
General Troubleshooting Information . 22-3
.......................... ..........................
Removal and Installation . 22-65
..........................
..........................
Removal and Installation . 22-66
.......................................................................................... .............
................................................
.......................................... .............
Battery Test
. 22-67
Battery Terminal Disconnection and Reconnection . 22-68
Battery Removal and Installation . 22-69
.......................................
.......................................
Power Relay Test . 22-70
............................................................. ..............................................
.............................................................
..............................................
Test
. 22-72
Replacement . 22-72
...................... .....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
......................................... ......................
.....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
.........................................
Component Location Index
. 22-73
General Troubleshooting Information . 22-74
DTC Troubleshooting Index . 22-77
System Description . 22-80
Troubleshooting-B-CAN System Diagnosis Test Mode A . 22-93
Troubleshooting-B-CAN System Diagnosis Test Mode B . 22-94
Troubleshooting-B-CAN System Diagnosis Test Mode C . 22-95
Troubleshooting-B-CAN System Diagnosis Test Mode D . 22-96
Troubleshooting-B-CAN System Diagnosis Test Mode 1 and
Test Mode 2 (Without the HDS) . 22-97
Sleep and Wake-up Mode Test . 22-99
Circuit Diagram . 22-100
DTC Troubleshooting . 22-102
MICU Input Test . 22-109 ......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
Component Location Index
. 22-112
System Description . 22-114
Circuit Diagram . 22-116
DTC Troubleshooting . 22-120
Symptom Troubleshooting . 22-126
Tripped Sensor History . 22-130
MICU Input Test . 22-131
Door Lock Actuator Test . 22-137
Door Lock Knob Switch Test . 22-138
Door Lock Switch Test . 22-139
Door Key Cylinder Switch Test . 22-140
Trunk Lid Release Actuator Test . 22-141
Hood Switch Test . 22-141
Transmitter Test/Replacement . 22-142
......................
.......................................... ............................
....................................... ......................
.......................................... ............................
.......................................
Component Location Index
. 22-145
Circuit Diagram . 22-146
Horn Test/Replacement . 22-146
Horn Switch Test . 22-147
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
Component Location Index
. 22-148
Circuit Diagram . 22-150
DTC Troubleshooting . 22-157
MICU Input Test . 22-163
Combination Light Switch Test/ Replacement . 22-166
HID Bulb Replacement . 22-168
HID Unit Replacement . 22-169
HID Lamp System Troubleshooting . 22-170
Headlight Adjustment . 22-173
Headlight Replacement . 22-174
Fog Light Replacement . 22-175
Fog Light Adjustment . 22-176
Bulb Replacement . 22-177
Taillight Replacement . 22-179
Inner Taillight Replacement . 22-179
License Plate Light Replacement . 22-180
High Mount Brake Light Replacement . 22-180
Brake Pedal Position Switch Test . 22-181
......................
.......................................... ................................
.........................................
.................................. .......
......................
.......................................... ................................
.........................................
.................................. .......
Component Location Index
. 22-182
Circuit Diagram . 22-184
DTC Troubleshooting . 22-186
MICU Input Test . 22-188
Hazard Warning Switch Test/Replacement . 22-192
Side Turn Signal Light Replacement . 22-192
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
Component Location Index
. 22-193
Circuit Diagram . 22-194
Front Individual Map Light Test/ Replacement . 22-196
Ceiling Light Test/Replacement . 22-197
Trunk Light Replacement . 22-197
Ambient Light Test/Replacement . 22-198
Courtesy Light Replacement . 22-198
Glove Box Light Test/Replacement . 22-199
Vanity Mirror Light Test/Replacement . 22-199
Interior Light Switch Test/Replacement . 22-200
Trunk Lid Latch Switch Test . 22-200
Footwell Light Test/Replacement . 22-201
08/08/21 14:22:03 61SNR030_220_0002
ProCarManuals.com
DYNOMITE -2009-

•••
•••
•••
•••
(#')
 Under-hood Fuse/Relay Box
Fuse
Number Amps Component(s) or Circuit(s) Protected
22-60Power Distribution
Fuse to Components Index
1 100 A
(BAT)Battery, Power distribution
70 A
(EPS) EPS control unit
250A (IG)Ignition switch
80 A
60 A
(OPTION) No. 5, No. 6, No. 7, No. 27, No. 28, No. 29, and No. 31 fuses (in the under-dash fuse/relay box)
330A (ABS MTR) ABS modulator-control unit , VSA modulator-control unit
30 A
40 A
(ABS FSR) ABS modulator-control unit , VSA modulator-control unit
450A (H/L)No. 18, No. 19, No. 20, and No. 21 fuses (in the under-dash fuse/relay box)
40 A
(P/W) No. 24, No. 25, No. 26, No. 30, No. 32, and No. 33 fuses (in the under-dash fuse/relay box), Power window relay
(in the under-dash fuse/relay box)
5 Not used
6 20 A A/C condenser fan motor (via A/C condenser fan relay)
7 20 A Radiator fan motor (via radiator fan relay)
8 30 A Noise condenser (via rear window defogger relay), Rear window defogger (via rear window defogger relay)
9 40 A Blower motor (via blower motor relay)
10 10 A MICU (turn signal/hazard warning lights circuit)
11 15 A A/F sensor (Sensor 1) (via PGM-FI subrelay), EVAP canister vent shut valve (via PGM-FI subrelay), PGM-FI subrelay, No. 15 fuse (in the under-hood fuse/relay box) (via PGM-FI subrelay)
12 15 A Brake lights, ECM/PCM, Horn, MICU
13 Not used
14 Not used
15 7.5 A A/C condenser fan relay
16 Not used
17 15 A Stereo amplifier
18 15 A Ignition coil relay, Ignition coils (via Ignition coil relay)
19 15 A CKP sensor (via PGM-FI main relay 1), CMP sensor B (via PGM-FI main relay 1), ECM/PCM, ETCS control relay, Injectors (via PGM-FI main relay 1), PGM-FI main relay 1 (FI MAIN), PGM-FI main relay 2 (FUEL PUMP)
20 7.5 A A/C compressor clutch (via A/C compressor clutch relay)
21 15 A ECM/PCM (via ETCS control relay)
22 7.5 A Ceiling light, Courtesy lights, Front individual map lights, Ignition key light, Trunk light, Vanity mirror lights
23 10 A Audio unit , Data link connector (DLC), Gauge control module (speedo), Gauge control module (tach), HandsFreeLink control unit , Immobilizer-keyless control unit, MICU, Moonroof switch, Navigation unit
1: ’06-07 models
2: ’08-09 models
3: ’06-07 Touring and Premium models
4: ’07 TYPE S and ’08-09 models
5: ’08-09 models
6: TYPE S model
7: Without navigation system
8: With navigation system
9: ’09 model with navigation system
1
2
34
3
4 34
6 5
7 9 8
08/08/21 14:24:02 61SNR030_220_0062
ProCarManuals.com
DYNOMITE -2009-

•••
•••´
´
•••
Under-dash Fuse/Relay Box
Fuse
Number Amps
Component(s) or Circuit(s) Protected
22-62Power Distribution
Fuse to Components Index (cont’d)
1 7.5 A Power mirror switch light
2 15 A ECM/PCM, Fuel pump (via PGM-FI main relay 2), Immobilizer-keyless control unit
3 10 A Alternator, CMP sensor A, ECM/PCM (via brake pedal position switch), ELD, EVAP canister purge valve, MAF
sensor/IAT sensor, Reverse lockout solenoid , Secondary HO2S (sensor 2)
4 7.5 A ABS modulator-control unit , EPS control unit, VSA modulator-control unit , Yaw rate-lateral acceleration sensor
5 15 A Seat heaters (via seat heater relays)
6 20 A Fog light relay, Fog lights (via fog light relay)
7 Not used
8 Not used
9 7.5 A ODS unit, Passenger’s airbag cutoff indicator, SRS unit
10 7.5 A Back-up light (M/T), Gauge control module (speedo), Gauge control module (tach), MICU, Shift lock solenoid (A/T), TPMS control unit
11 10 A SRS unit
12 10 A Right headlight (high beam)
13 10 A Left headlight (high beam)
14 7.5 A Audio unit light , Climate control unit light, Dash lights brightness controller and odometer select/reset switch light, Driver’s footwell light , Driver’s seat heater switch light, Glove box light, Hazard warning switch light,
Moonroof switch light, Navigation unit , Park pin switch light (A/T), Passenger’s airbag cutoff indicator light,
Passenger’s footwell light , Passenger’s seat heater switch light, Steering wheel switches light (via cable reel),
VSA OFF switch light
15 7.5 A Parking lights, Taillights, License plate lights, Side marker lights
16 10 A Right headlight (low beam) 15 A Right HID unit
17 10 A Left headlight (low beam) 15 A Left HID unit
18 20 A MICU ( B H/L HI)
19 15 A MICU ( B SMALL LT)
20 Not used
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S model
5: With HID
6: Without HID
7: TYPE S and ’08 Premium and ’09 models
8: Without navigation system
9: With navigation system
4
1 2
2
7
3
8 49
4
6
5
6
5
08/08/21 14:24:03 61SNR030_220_0064
ProCarManuals.com
DYNOMITE -2009-

µ
(#'
)
GroundComponent or Circuit Grounded
22-64Ground Distribution
Ground to Components Index
G1 Battery
G2 Engine
G3 Transmission housing
G101 A/T clutch pressure control solenoid valves A, B, C (A/T), CKP sensor, CMP sensor A, CMP sensor B, Data link connector (DLC), ECM/PCM (LG1), ECM/PCM (LG2), ECM/PCM (PG1), ECM/PCM (PG2), ECM/PCM (PGMETCS), EGR valve (K20Z2 engine), Ignition
coils, Immobilizer-keyless control unit, Rocker arm oil control solenoid, Rocker arm oil pressure switch, Transmission range
switch (A/T), VTC oil control solenoid valve
Shielding between the ECM/PCM and Knock sensor (KS) has wire.
Shielding between the ECM/PCM and Secondary HO2S (Sensor 2) has wire.
G201 Right fog light , Right front parking light, Right front side marker light, Right front turn signal light, Right headlight (high/low beams), Right HID unit , Windshield washer motor, Windshield wiper motor
G202 ABS modulator-control unit , VSA modulator-control unit
G301 A/C condenser fan motor, Blower motor relay, ELD, Left fog light , Left front parking light, Left front side marker light, Left front turn signal light, Left headlight (high/low beams), Left HID unit , Radiator fan motor (via fan control relay)
G401 Brake fluid level switch, Clutch interlock switch (M/T), Clutch pedal position switch (M/T), Hood switch, MICU (PG), Power transistor, Washer fluid level switch (G401 connects to G601 via under-dash fuse/relay box)
G402 EPS control unit
G403 Torque sensor
G501 Dash lights brightness controller and odometer select/reset switch, Driver’s door key cylinder switch, Driver’s door lock knob switch, HandsFreeLink control unit , MICU (SG), VSA OFF switch
G502 Data link connector (DLC), Front accessory power socket, Glove box light, Right power mirror defogger, Right side turn signal light
G503 Accessory power socket relays (front and console), Driver’s door lock switch, Gauge control module (tach), Left power mirror defogger, Left side turn signal light, Moonroof control unit/motor, Power mirror switch light, Power mirror switch, Power
window master switch (main switch), Power window master switch, Vanity mirror lights (driver’s and front passenger’s)
G504 Cable reel (steering wheel switches ground), Climate control unit, Front passenger’s door lock knob switch, Front passenger’s door lock switch, Gauge control module (speedo), Gauge control module (tach), Ignition key switch, Navigation unit , TPMS
control unit
G505 Audio unit , Navigation unit
G506 Memory erase signal (MES) connector, SRS unit (2 wires)
G601 A/T gear position console panel light/Park-pin switch (A/T), Console accessory power socket , Fuel pump, MICU (PG), Seat heater relays (driver’s and front passenger’s), Seat heater switches (driver’s and front passenger’s), Seat heaters (driver’s and
front passenger’s), Stereo amplifier (G601 connects to G401 via under-dash fuse/relay box)
Shielding between the left side impact sensor (FIRST) and rear safing sensor has wire.
Shielding between the SRS unit and left side impact sensor (FIRST) has wire.
G602 Driver’s seat belt buckle switch, Front passenger’s seat belt buckle switch, Left rear door lock knob switch, MICU (SG), MICU service check connector, ODS unit, Right rear door lock knob switch, Yaw rate-lateral acceleration sensor
Shielding between the right side impact sensor (FIRST) and right side impact sensor (SECOND) have wires.
Shielding between the SRS unit and right side impact sensor (FIRST) has wire.
G603 Noise condenser Shielding between the rear safing sensor and left side impact sensor (SECOND) has wire.
G701 High mount brake light, Left back-up light, Left inner taillight, Left rear side marker light, Left rear turn signal light, Left taillight/ brake light, License plate lights, Right back-up light, Right inner taillight, Right rear side marker light, Right rear turn signal light,
Right taillight/brake light, Trunk lid release actuator/Trunk lid latch switch
G801 Rear window defogger ( )
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S and ’08 premium and ’09 models
5: With HID
6: Without navigation system
7: With navigation system
8: ’09 model with navigation system
9: ’06-08 models, and ’09 model without navigation system
10: TYPE S model
4
512 4
5
82 3
7
3
67
9
10
2
08/08/21 14:24:03 61SNR030_220_0066
ProCarManuals.com
DYNOMITE -2009-

µ
µ
HDS Inputs and Commands
Input:System Menu Data List Data List Indication
22-88Multiplex Integrated Control System
System Description (cont’d)
Certain inputs happen so quickly that the HDS cannot update fast enough. Hold the switch that is being tested while monitoring the Data List.
This should give the HDS time to update the signal on the Data List.
Because the HDS software is updated to support the release for newer vehicles it is not uncommon to see system function tests that are not
supported.
Make sure that the most current software is loaded.
Gauges Cruise Control Main Switch OFF/ON Cruise Control Set Switch OFF/ON
Cruise Control Resume Switch OFF/ON
Washer Fluid Level Switch OFF/ON
VSA/TCS Off Switch OFF/ON
Gauge Select/Reset Switch OFF/ON
Parking Brake Switch OFF/ON
Brake Fluid Level Switch OFF/ON
Illumination Volume Plus Switch OFF/ON
Illumination Volume Minus Switch OFF/ON
Km/h mph Select Switch OFF/ON
Fuel Sending Unit Input 1 deg
Fuel Sending Unit Input 2 VOLTAGE
VSA/TCS Active Indicator OFF/ON
VSA/TCS Indicator (Warning) OFF/ON
ABS Indicator OFF/ON
Cruise Control Main Switch Indicator OFF/ON
MIL Indicator OFF/ON
Washer Fluid Level Indicator OFF/ON
DRL Indicator OFF/ON
Low Oil Pressure Indicator OFF/ON
Charging System Indicator OFF/ON
Cruise Main Switch ON Indicator OFF/ON
Maintenance Minder Indicator OFF/ON
High Beam Indicator OFF/ON
Parking Light ON Indicator OFF/ON
Low Fuel Warning Indicator OFF/ON
Security Indicator OFF/ON
Fog Light Indicator OFF/ON
Seat Belt Indicator OFF/ON
Speed Indicator (km/h) 0 249 km/h, over 250 km/h, Fail
Speed Indicator (mph) 0 154 mph, over 155 mph, Fail
Low Tire Pressure Indicator OFF/ON
TPMS Indicator OFF/ON
A/TGearPositionSwitch(R) OFF/ON
A/TGearPositionSwitch(P) OFF/ON
08/08/21 14:24:09 61SNR030_220_0090
ProCarManuals.com
DYNOMITE -2009-