2006 ACURA CSX navigation system

´
µ
´
µ
´
µ
´
µ
Î Î
´
µ
µ µ
µ
Speaker Terminal Wire color
YES
NO YES
NO
23-208Audio System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (24P)
STEREO AMPLIFIER CONNECTOR A (20P)
BAUDIO
AMP
(LT GRN)
13. Check for continuity between body ground and the
following terminals of navigation unit connector A
(24P).
Driver’s door speaker,
Left tweeter A23 ( ) LT GRN
A22 ( ) PNK
Front passenger’s
door speaker,
Right tweeter A19 ( ) GRY
A18 ( ) BRN
Left rear speaker A11 ( ) YEL A10 ( ) BRN
Right rear speaker A7 ( ) BLU A6 ( ) ORN
Repair short to body ground in the wire(s)
between the navigation unit and the speaker(s).
Substitute a known-good navigation unit
(see page 23-355), and recheck. If the symptom/
indication goes away, replace the original
navigation unit. 14. Measure the voltage between stereo amplifier
connector A (20P) terminal No. 10 and body ground.
Go to step 15.
Repair open in the wire between the No. 17
(15 A) fuse in the under-hood fuse/relay box and
stereo amplifier connector A (20P) terminal
No. 10.
Wire side of female terminals Wire side of female terminals
Is there continuity?
Is there battery voltage?
08/08/21 14:10:45 61SNR030_230_0211
ProCarManuals.com
DYNOMITE -2009-

Î
Î

µ
µ µ
µ
Stereo amplifier connector Wire color
YES
NO Navigation
unit connector Stereo
amplifier
connector Wire color
YES
NO
23-212 Audio System
Symptom Troubleshooting (cont’d)
STEREO AMPLIFIER CONNECTOR B (14P)
STEREO AMPLIFIER CONNECTOR B (14P)NAVIGATION UNIT CONNECTOR A (24P)
27. Check for continuity between stereo amplifier
connector B (14P) and body ground according to
the table. Then check for continuity between the
same terminals listed in the table and stereo
amplifier connector B (14P) terminal No. 5 (the
harness shield).
B4 BLU
B11 PNK
Short in the wire between the stereo
amplifier and the navigation unit. Replace the
affected shielded harness.
Go to step 28. 28. Check for continuity between navigation unit
connector A (24P) and stereo amplifier connector B
(14P) according to the table.
A16 B11 PNK
A19 B4 BLU
Go to step 29.
Open in the wire between the navigation unit
and the stereo amplifier. Replace the affected
shielded harness.
Wire side of female terminals
Wire side of female terminalsWire side of female terminals
Is there continuity?
Is there continuity?
08/08/21 14:10:47 61SNR030_230_0215
ProCarManuals.com
DYNOMITE -2009-

Î
Î
µ
µ µ
µ
Stereo amplifier connector Wire color
YES
NO Navigation
unit connector Stereo
amplifier
connector Wire color
YES
NO
23-214 Audio System
Symptom Troubleshooting (cont’d)
STEREO AMPLIFIER CONNECTOR B (14P)
STEREO AMPLIFIER CONNECTOR B (14P)NAVIGATION UNIT CONNECTOR A (24P)
31. Check for continuity between stereo amplifier
connector B (14P) and body ground according to
the table. Then check for continuity between the
same terminals listed in the table and stereo
amplifier connector B (14P) terminal No. 12 (the
harness shield).
B6 LT GRN
B13 PUR
Short in the wire between the stereo
amplifier and the navigation unit. Replace the
affected shielded harness.
Go to step 32. 32. Check for continuity between navigation unit
connector A (24P) and stereo amplifier connector B
(14P) according to the table.
A6 B13 PUR
A7 B6 LT GRN
Substitute a known-good navigation unit
(see page 23-355), and recheck. If the symptom/
indication goes away, replace the original
navigation unit. If the symptom is still present,
substitute a known-good stereo amplifier, and
recheck. If the symptom/indication goes away,
replace the original stereo amplifier (see page
23-259).
Open in the wire between the navigation unit
and the stereo amplifier. Replace the affected
shielded harness.
Wire side of female terminals
Wire side of female terminalsWire side of female terminals
Is there continuity?
Is there continuity?
08/08/21 14:10:47 61SNR030_230_0217
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
µ
µ
µ
µ
From terminal To terminals
YES
NO Navigation
unit connector Auxiliary jack
assembly
connector Wire color
YES
NO
23-218 Audio System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR B (24P)
AUXILIARY JACK ASSEMBLY 5P CONNECTORNAVIGATION UNIT CONNECTOR B (24P)
11. Check for continuity between navigation unit
connector B (24P) according to the table.
B1 B2 , B3, B13, B14, B15
B2 B3, B13, B14, B15 B3 B13, B14, B15
B13 B14, B15
B14 B15
: Shielded wire
Short in the wire(s) between the navigation
unit and the auxiliary jack assembly. Replace the
affected shielded harness.
Go to step 12. 12. Check for continuity between navigation unit
connector B (24P) and aux iliary jack assembly 5P
connector according to the table.
B1 3 BRN
B3 2 BLU
B13 4 YEL
B14 5 GRN
B15 1 WHT
Substitute a known-good aux iliary jack
assembly (see page 23-261), and recheck. If the
symptom/indication goes away, replace the
original auxiliary jack assembly. If the symptom/
indication is still present, replace the navigation
unit (see page 23-355).
Open in the wire(s) between the navigation
unit and the auxiliary jack assembly. Replace the
affected shielded harness.
Wire side of female terminals
Wire side of female terminalsWire side of female terminals
Is there continuity?
Is there continuity?
08/08/21 14:10:48 61SNR030_230_0221
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)

µ
µ µ
µ
Audio unit
connector Auxiliary jack
assembly
connector Wire color
YES
NO YES
NO
Audio system sound is weak or distorted
(display is normal)
23-22023-220Audio System
Symptom Troubleshooting (cont’d)
AUDIO UNIT CONNECTOR B (20P)
AUXILIARY JACK ASSEMBLY 5P CONNECTOR
17. Check for continuity between audio unit connector B (20P) and auxiliary jack assembly 5P c onnector
accordingtothetable.
B3 3 BRN
B5 2 BLU
B13 4 YEL
B14 5 GRN
B15 1 WHT
Substitute a known-good aux iliary jack
assembly (see page 23-261), and recheck. If the
symptom/indication goes away, replace the
original auxiliary jack assembly. If the symptom/
indication is still present, replace the audio unit
(see page 23-256).
Open in the wire(s) between the audio unit
and the auxiliary jack assembly. Replace affected
shielded harness. NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
1. Check for sound in each mode (AM, FM, XM, and CD).
Intermittent failure. The system is OK at this
time. Check for loose connections at the navigation
unit, audio unit, amplifier, and each speaker.
Speakers all work, sound quality is poor.
 If the sound quality is poor only with the XM radio, or the XM radio does not function, go to
poor or no sound with XM radio (see page
23-249).
 If the sound quality is poor only with AM or FM radio, go to poor AM or FM radio reception or
interference (see page 23-196).
 If sound is poor in all modes, go to sound quality diagnosis (see page 23-251).
Wire side of female terminals
Wire side of female terminals
Is there continuity? I s t her e sound f r om t he speak er s, and i s t he sound
qual i t y nor mal i n each mod e?
08/08/21 14:10:49 61SNR030_230_0223
ProCarManuals.com
DYNOMITE -2009-

(#'
)
(#'
)

µ
µ
µ
µ µ
µ
µ
µ
Radio preset memory is lost Volume does not change
YES
NO
YES
NO YES
NO
YES
NO
23-22123-221
NOTE: If only the XM stations are lost, go to XM radio
preset memory is lost (see page 23-248).
1. Set each of the radio station preset buttons.
Go to step 2.
 With navigation: Replace the navigation unit (see page 23-355).
 Without navigation: Replace the audio unit (see page 23-256).
2. Turn the ignition switch to LOCK (0) for 1 minute, then turn it back to ON (II).
3. Test the preset buttons for proper recall operation.
System is normal at this time. Check the
connections at the navigation unit or audio unit.
 With navigation: Replace the navigation unit (see page 23-355).
 Without navigation: Replace the audio unit (see page 23-256). NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
 Set the fader and balance positions to the center.
1. Listen for sound from the speakers.
Go to step 2.
Go to audio system sound is weak or
distorted, or no sound is heard from speaker(s)
(see page 23-206).
2. Operate the volume knob to see if the volume changes.
Operation is normal.
 With navigation: Replace the navigation unit (see page 23-355).
 Without navigation: Replace the audio unit (see page 23-256).
Do each of t he but t ons set pr oper l y ?
Do the preset buttons recall the set radio stations? I s t he sound nor mal ?
Does t he v ol ume change?
08/08/21 14:10:49 61SNR030_230_0224
ProCarManuals.com
DYNOMITE -2009-

µ
Î
(#'
)

µ
µ
µ
µ
µ
µ µ
µ
Volume does not increase with speed (with
navigation)
YES
NO
YES
NO
YES
NO YES
NO
23-222Audio System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (24P)
VSP (BLU)
NOTE: Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
1. Verify the SVC mode setting in the navigation unit sound set-up.
Change the setting to Mid and retest
(see page 23-164).
Go to step 2.
2. Do the self-diagnostic function for the vehicle speed pulse indication (see page 23-190).
Substitute a known-good navigation unit
(see page 23-355), and retest. If the symptom/
indication goes away, replace the original
navigation unit.
Go to step 3.
3. Test-drive the vehicle at highway speeds, and monitor if the volume increases.
Intermittent failure, the system is OK at this
time.
Go to step 4. 4. Remove the navigation unit (see page 23-355) and
disconnect navigation unit connector A (24P).
NOTE: Eject all the discs before removing the navigation unit to prevent damaging the CD player’s load
mechanism.
 Remove the PC card before removing the navigation unit.
5. Drive the vehicle, and have an assistant measure voltage at navigation unit connector A (24P)
terminal No. 15.
Replace the navigation unit (see page 23-355).
Repair open or shorts in the wire between
navigation unit connector A (24P) terminal No. 15
and ECM/PCM connector A (44P) terminal No. 29. If
no opens or shorts are found, Update the ECM/
PCM (see page 11-227) if it does not have the latest
software or substitute a known-good ECM/PCM
(see page 11-228).
Wire side of female terminals
Is the SVC set to off?
Does t he sel f -d i agnost i c f unct i on i nd i cat e a V SPsi gnal ?
Do t he v ol ume i ncr ease? Is there a 0 5 V Pulse?
08/08/21 14:10:49 61SNR030_230_0225
ProCarManuals.com
DYNOMITE -2009-

µ
Î

(#'# 
)

µ
µ
µ
µ
µ
µ µ
µ
Volume does not increase with speed
(without navigation)
YES
NO
YES
NO
YES
NO YES
NO
23-223
AUDIO UNIT CONNECTOR A (17P)
VSP (BLU)
NOTE: Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
1. Test-drive the vehicle at highway speeds, and monitor if the volume increases.
Intermittent failure, the system is OK at this
time.
Go to step 2.
2. Verify the SVC mode setting in the audio unit sound set-up.
Change the setting to Mid, and retest
(see page 23-164).
Go to step 3.
3. Do the self-diagnostic function for the vehicle speed pulse indication (see page 23-190).
Substitute a known-good audio unit
(see page 23-256), and retest. If the symptom/
indication goes away, replace the original audio
unit.
Go to step 4. 4. Remove the audio unit (see page 23-256) and
disconnect audio unit connector A (17P).
NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
5. Drive the vehicle, and have an assistant measure voltage at audio unit connector A (17P) terminal
No. 13.
Replace the audio unit (see page 23-256).
Repair open or shorts in the wire between
audio unit connector A (17P) terminal No. 13 and
ECM/PCM connector A (44P) terminal No. 29. If no
opens or shorts are found, Update the ECM/PCM
(see page 11-227) if it does not have the latest
software or substitute a known-good ECM/PCM
(see page 11-228).
Wire side of female terminals
Do t he v ol ume i ncr ease?
Is the SVC set to off?Does t he sel f -d i agnost i c f unct i on i nd i cat e a V SPsi gnal ? Is there a 0 5 V Pulse?
08/08/21 14:10:49 61SNR030_230_0226
ProCarManuals.com
DYNOMITE -2009-