2006 ACURA CSX seats

Ì
 

(#'



 )
14-30214-302 Valve Body
Valve Body Repair (cont’d)
Valve Body Valve Installation
C
A B
5. Remove the 600 paper. Thoroughly wash the
entire valve body in solvent, then dry it with
compressed air.
6. Coat the valve with ATF, then drop it into its bore. It should drop to the bottom of the bore under its
own weight. If not, repeat step 4, then retest. If the
valve still sticks, replace the valve body.
7. Remove the valve, and thoroughly clean it and the valve body with solvent. Dry all parts with
compressed air, then reassemble using ATF as a
lubricant. 1. Coat all parts with ATF before assembly.
2. Install the valves and the springs in the sequence
shown for the main valve body (see page 14-303),
the regulator valve body (see page 14-305), and the
servo body (see page 14- 306). Refer to the
following valve cap illustrations, and install each
valvecapsotheendshownfacingupwillbefacing
the outside of the valve body.
3. Install all the springs and the seats. Insert the spring (A) in the valve, then install the valve in the
valve body (B). Push the spring in with a
screwdriver, then install the spring seat (C).
08/08/21 14:51:12 61SNR030_140_0304
ProCarManuals.com
DYNOMITE -2009-

Ì
 

(#'



 )
14-30214-302 Valve Body
Valve Body Repair (cont’d)
Valve Body Valve Installation
C
A B
5. Remove the 600 paper. Thoroughly wash the
entire valve body in solvent, then dry it with
compressed air.
6. Coat the valve with ATF, then drop it into its bore. It should drop to the bottom of the bore under its
own weight. If not, repeat step 4, then retest. If the
valve still sticks, replace the valve body.
7. Remove the valve, and thoroughly clean it and the valve body with solvent. Dry all parts with
compressed air, then reassemble using ATF as a
lubricant. 1. Coat all parts with ATF before assembly.
2. Install the valves and the springs in the sequence
shown for the main valve body (see page 14-303),
the regulator valve body (see page 14-305), and the
servo body (see page 14- 306). Refer to the
following valve cap illustrations, and install each
valvecapsotheendshownfacingupwillbefacing
the outside of the valve body.
3. Install all the springs and the seats. Insert the spring (A) in the valve, then install the valve in the
valve body (B). Push the spring in with a
screwdriver, then install the spring seat (C).
08/08/21 14:51:12 61SNR030_140_0304
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'
 )
Special Tools Required
18-13
Ball Joint Boot Inspection/Replacement
A
B
C
D (Multipurpose)
(Multipurpose) A
07GAF-SE00200
Press
Attachment, 40 mm 07GAF-SE00200
1. Check the ball joint boot for weakness, damage, cracks, and grease leaks.
NOTE: If the ball joint boot is damaged with grease leaks, replace the appropriate part as an assembly.
 If the ball joint boot is soft and cracked without grease leaks, go to step 2. Replace the
appropriate ball joint boot.
2. Disconnect the appropriate ball joint connection, and remove the component including the ball joint.
The lower ball joint (see page 18-20).
3. Remove the boot.
4. Pack the interior and lip (A) of a new boot with grease. Keep the grease off of the boot-to-lower
ball joint housing mating surfaces (B).
5. Pack fresh grease into the base (C). Do not let dirt or other foreign materials get into the boot.
6. Install the boot on the ball joint, then squeeze it gently to force out any air, then wipe the grease off
the tapered portion of the ball joint pin (D). 7. Press the boot with the attachment until the bottom
seats on the lower ball joint housing (A) all the way
around.
8. After installing a boot, wipe any grease off the
exposed portion of the ball joint pin.
9. Install all of the removed parts.
08/08/21 14:56:49 61SNR030_180_0013
ProCarManuals.com
DYNOMITE -2009-

Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior TrimFenderwell
Openers
Frame......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
Component Location Index
. 20-116
Front Seat Active Head Restraint Inspection . 20-117
Front Seat Removal/Installation . 20-118
Front Seat Frame Replacement . 20-120
Front Seat-back Cover Replacement . 20-123
Front Seat Cushion Cover Replacement . 20-127
Rear Seat Removal/Installation . 20-131
Rear Seat-back Latch Replacement . 20-135
Rear Seat-back Release Lever/Cable Removal/Installation . 20-136
Rear Seat Armrest Beverage Holder Replacement . 20-137
Rear Seat Armrest Replacement . 20-138
Rear Seat-back Cover Replacement . 20-139
Rear Seat Side Bolster Cover Replacement . 20-143
Rear Seat Cushion Cover Replacement . 20-143
Rear Seat Armrest Cover Replacement . 20-144
.........
...........................................
........................................... ..........
........................................... .........
...........................................
........................................... ..........
...........................................
Front Bumper Removal/Installation . 20-146
Front Bumper Lower Grille
Replacement . 20-148
Front Bumper Lower Side Plate Replacement . 20-148
Rear Bumper Removal/Installation . 20-149
Rear Bumper Lower Cover Replacement . 20-151
...................................... ................................................
......................................
................................................
Hood Adjustment
. 20-152
Hood Seal Replacement . 20-153
Hood Insulator Replacement . 20-154
................................ ..............
..............
................................
..............
..............
Trunk Lid Adjustment
. 20-155
Trunk Lid Torsion Bar Replacement . 20-156
Trunk Lid Weatherstrip Replacement . 20-157
Trunk Lid Cushion Replacement . 20-157
.........................................
.........................
................
Fuel Fill Door Adjustment
. 20-158
Fuel Cap Adapter Replacement . 20-159
........................................
...............
.......................... ......................
...................... ...
..............
................
..................
..........................
..............
...............
.......................... ......................
...................... ...
..............
................
..................
Front Grille Replacement
. 20-160
Front Fender Trim Replacement . 20-162
Front Grille Cover Replacement . 20-163
Cowl Cover Replacement . 20-163
Roof Molding Replacement . 20-165
Door Molding Replacement . 20-167
Side Sill Protection Tape Replacement . 20-168
Rear License Trim Replacement . 20-168
Trunk Lid Spoiler Replacement . 20-169
Emblem/Sticker Replacement . 20-170 .............
...................... ............
......
.............
.............
......................... .................... .............
...................... ............
......
.............
.............
......................... ....................
Front Inner Fender Replacement . 20-171
Splash Shield Replacement
. 20-172
Front Fender Fairing Replacement . 20-173
Middle Floor Undercover Replacement . 20-174
Rear Floor Undercover Replacement . 20-174
Fuel Pipe Protector Replacement . 20-175
Rear Fender Cover Replacement . 20-175
Rear Strake Replacement . 20-176
Rear Air Outlet Replacement . 20-176
...................... ............
..................
..........................
........................................... .....
...................
......................
............
..................
..........................
........................................... .....
...................
Component Location Index
. 20-177
Hood Opener Cable Replacement . 20-178
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement . 20-179
Hood Latch Replacement . 20-181
Trunk Lid Opener/Fuel Fill Door Opener Replacement . 20-182
Trunk Lid Lock Cylinder Replacement . 20-184
Trunk Lid Latch Replacement . 20-185
...........................................
........................................... ............................
...................................
...........................................
...........................................
............................
...................................
Upper Dashboard Support Gusset
Replacement . 20-186
Rear Floor Upper Cross-member Gusset Replacement . 20-186
Subframe Replacement . 20-187
Frame Repair Chart . 20-188
08/08/21 14:58:49 61SNR030_200_0003
ProCarManuals.com
DYNOMITE -2009-




20-85
A
B
B
A
B D
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
Fastener Locations
:Bolt,2
C
E
F
G A
B
C
A
Fastener Locations :Bolt,4
8x1.25mm
22 N·m
(2.2 kgf·m,
16 lbf·ft) A
6. Push the hook (A) with a flat-tip screwdriver
wrapped with protective tape, and turn the holder
(B) 90 °, then pull it out.
7. Remove the individual map light assembly (A). –1 Remove the lenses (B).
–2 Remove the bolts.
–3 If equipped, release the four tabs (C), then pullout the moonroof switch (D) or the navigation
microphone.
–4 Disconnect the front individual map light connector (E). If equipped, disconnect the
moonroof switch connector (F) and the
navigation microphone connector (G). 8. Without moonroof: Remove the driver’s dashboard
undercover (see page 20-104).
9. Detach the harness clips (A) from the A-pillar (B), and disconnect the roof wire harness connector (C).
10. Remove the center console (see page 20-92).
11. Slide both front seats all the way back, and recline the seat-backs fully.
12. Remove the bolts securing the parking brake base frame (A), and lay it down as needed.
(cont’d)
08/08/21 15:01:40 61SNR030_200_0087
ProCarManuals.com
DYNOMITE -2009-







(#'


 )
H

eadliner
Grab handle
Sunvisor Special Tools Required
20-8820-88
Interior Trim
Headliner Removal/Installation
(cont’d)
Carpet Replacement
A
C
H
I
C
J K
B
B
F
D
E G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to damage, wrinkle, or twist the carpet.
 Be careful not to damage the dashboard or other interior trim pieces.
1. Remove these items:  Front seats, both sides (see page 20-118)
 Rear seat cushion (see page 20-133)
 Front door sill trim, both sides (see page 20-66)
 Rear door sill trim, both sides (see page 20-67)
 Kick panels, both sides (see step 5 on page 20-67)
 B-pillar lower trim (see page 20-72)
 Driver’s dashboard undercover (see page 20- 103)
 Passenger’s dashboard undercover (see page 20-104)
 Center console (see page 20-92)
 Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
ProCarManuals.com
DYNOMITE -2009-







(#'


 )
H

eadliner
Grab handle
Sunvisor Special Tools Required
20-8820-88
Interior Trim
Headliner Removal/Installation
(cont’d)
Carpet Replacement
A
C
H
I
C
J K
B
B
F
D
E G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to damage, wrinkle, or twist the carpet.
 Be careful not to damage the dashboard or other interior trim pieces.
1. Remove these items:  Front seats, both sides (see page 20-118)
 Rear seat cushion (see page 20-133)
 Front door sill trim, both sides (see page 20-66)
 Rear door sill trim, both sides (see page 20-67)
 Kick panels, both sides (see step 5 on page 20-67)
 B-pillar lower trim (see page 20-72)
 Driver’s dashboard undercover (see page 20- 103)
 Passenger’s dashboard undercover (see page 20-104)
 Center console (see page 20-92)
 Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
ProCarManuals.com
DYNOMITE -2009-



20-94Consoles
Center Console Removal/Installation (cont’d)
A
B
C
B
A
B A
BC
8. Slide both front seats all the way back, and recline
the seat-back fully.
9. Slide the center console (A) rearward to release the pins (B) from the bracket (C).
10. Lift up the rear of the console (A), and remove it from the dashboard.
11. If equipped, disconnect the seat heater switch connectors (B). 12. Install the console in the reverse order of removal,
and note these items:
 Make sure each connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips and the hooks into place securely.
 When installing the center console panel, install the tabs (A) into the notch (B) of the parking brake
base frame (C).
08/08/21 15:02:48 61SNR030_200_0096
ProCarManuals.com
DYNOMITE -2009-