2006 ACURA CSX seats






20-130Seats
Front Seat Cushion Cover Replacement (cont’d)
A
B
A
A
A
A A
12. Release the hooks (A) from under the seat cushion
(B).
13. Pull back the edge of the seat-back cover all the way around, and release the clips (A), then remove
the seat-back cover. 14. Install the cover in the reverse order of removal,
and note these items:
 To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly
over the pad before securing the clips, the hooks,
and the hook strips.
 Replace any clips (A) you removed with new ones.
08/08/21 15:04:01 61SNR030_200_0132
ProCarManuals.com
DYNOMITE -2009-



20-132Seats
Rear Seat Removal/Installation (cont’d)
Fastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) FG
H
A B
C
D
E
B A
B
C
D
A
B
Front
4. Remove the left seat-back (A). –1 Fold the left seat-back down.
–2 Pull the rear center seat belt (B) out through theslit (C) in the seat belt guide (D).
–3 Release the Velcro fastener (E), and pull back the seat-back cover (F), then remove the bolt.
–4 Release the hooks (G) of the pivot bracket (H). 5. Extend the rear center seat belt (A) to remove the
left seat-back (B), then release the pivot shaft (C)
from the center pivot bracket (D).
6. If necessary, remove the bushing (A) from the center pivot bracket (B).
08/08/21 15:04:03 61SNR030_200_0134
ProCarManuals.com
DYNOMITE -2009-

Î

Seat Side Bolster
20-134Seats
Rear Seat Removal/Installation (cont’d)
C
D
E
C C
F
B
A
Fastener Location
:Bolt,1
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
2. While pushing down on the seat cushion (A), pullthe seat hook handles (B) to release the hooks (C).
3. Pull back the seat cushion to release the center seat belt (D) and seat belt buckles (E) from their slits (F),
and remove it.
4. Install the seat cushion in the reverse order of removal, and note these items:
 Before attaching the seat cushion, make sure there are no twists or kinks in the seat belts.
 When installing the seat cushion, slip the seat belt buckles through the slits in the seat cushion. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the seat cushion.
2. Remove the bolt.
08/08/21 15:04:03 61SNR030_200_0136
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-



20-140Seats
Rear Seat-back Cover Replacement (cont’d)
A
A
A B
C
A A
B C
Fastener Locations
:Clip,2
B : Clip, 2 C
Left seat-back C
B
Right seat-back B
C B
C A
4. Left seat-back: Pull out the center portion of the
armrest back panel (A) to release upper edge of the
armrest back panel.
5. Left seat-back: Pull out the armrest back panel (A) to release the hook (B) of the seat-back frame and
hook (C) of the seat-back cover. 6. Release the lower hook strip (A) and the clips (B, C).
08/08/21 15:04:07 61SNR030_200_0142
ProCarManuals.com
DYNOMITE -2009-