2006 ACURA CSX battery



13-21
A
B C
B
A 8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
(P/N 08798-9002) C
D B
C A
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
39. Connect the back-up light switch connector (A) and the output shaft (countershaft) speed sensor
connector (B). Install the harness clips (C).
40. Apply super high temp urea grease (P/N 08798-9002) to the end of the slave cylinder
pushrod. Install the slave cylinder (A), then install
the clutch line bracket (B). Be careful not to bend
the clutch line. 41. Install the battery base (A) with the coolant
reservoir (B).
42. Install the harness clips (C) and the intake air duct (D).
43. Install the air cleaner assembly (see page 11-345).
44. Do the battery installation procedure (see page 22-69).
45. Install the under-cowl panel and the cowl cover (see page 20-163).
46. Check the shift lever and the clutch operation.
47. Check the wheel alignment (see page 18-5).
48. Test-drive the vehicle.
08/08/21 14:44:55 61SNR030_130_0023
ProCarManuals.com
DYNOMITE -2009-

Î
(#'


)
(#'


)µ
µ
µ
µ
Driver can select reverse gear when vehicle
speed is 20 km/h (12 mph) or more
YES
NO
YES
NO
13-7413-74 Reverse Lockout System
Circuit Diagram
Symptom Troubleshooting
GRN/BLKYEL
1 2
BLK/YEL BLU
IG1
BAT WHT
BATTERY
UNDER-HOOD
FUSE/RELAY
BOX
IGNITION
SWITCH
IG1HOTinON(II)
and START (III)
UNDER-DASH
FUSE/RELAY
BOX
REVERSE
LOCKOUT
SOLENOID
No. 1
(100 A)
No. 3
(10 A) No. 2
(50 A)
GRN
ECM A27 RVS
NOTE:
 When checking if the transmission will shift to reverse while the wheels are being driven forward,
raise the vehicle on a lift, make sure it is securely
supported, and allow the front wheels to rotate freely.
 Do not release the clutch pedal if you can select reverse gear while the wheels are driven forward.
 When the vehicle is on a lift, and you make the wheels rotate, turn off the VSA system by the VSA
OFF switch.
1. Turn the ignition switch to LOCK (0).
2. Check the No. 3 (10 A) fuse in the under-dash fuse/ relay box.
Reinstallthefuse,thengotostep3.
Install a new No. 3 (10 A) fuse, and recheck. If
the fuse continues to blow, check for short to body
ground in the wire between the No. 3 (10 A) fuse in
the under-dash fuse/relay box and the r everse
lockout solenoid.
3. Test-drive the vehicle.
4. Check for fuel and emissions system’s DTC with the HDS.
Go to the indicated DTC’s troubleshooting.
Go to step 5.
IsthefuseOK?
Ar e t her e any DT Cs st or ed i n t he f uel andemi ssi ons?
08/08/21 14:46:39 61SNR030_130_0076
ProCarManuals.com
DYNOMITE -2009-

Î
Î
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
13-75
REVERSE LOCKOUT SOLENOID 2P CONNECTOR
IG1 (BLK/YEL) ECM CONNECTOR A (44P)
RVS (GRN) RVS (GRN/BLK)
REVERSE LOCKOUT SOLENOID 2P CONNECTOR
5. Turn the ignition switch to LOCK (0).
6. Disconnect the r everse lockout solenoid 2P
connector.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between reverse lockout solenoid 2P connector terminal No. 2 and body
ground.
Go to step 9.
Repair open in the wire between No. 3 (10 A)
fuse in the under-dash fuse/relay box and the
reverse lockout solenoid.
9. Turn the ignition switch to LOCK (0).
10. Jump the SCS line with the HDS.
11. Disconnect ECM connector A (44P). 12. Check for continuity between reverse lockout
solenoid 2P connector terminal No. 1 and ECM
connector A (44P) terminal No. 27.
Go to step 13.
Repair open in the wire between the reverse
lockout solenoid and the ECM.
13. Do the reverse lockout solenoid test (see page 13-77).
Check for loose terminals or poor
connections at the ECM. If necessary, update the
ECM if it does not have the latest software
(see page 11-227), or substitute a known- good ECM
(see page 11-7), then recheck. If the symptom goes
away with a known-good ECM, replace the original
ECM (see page 11-228).
Repair or replace the reverse lockout solenoid
(see page 13-77).
Wire side of female terminals Terminal side of female terminals
Wire side of female terminals
Is there battery voltage? Is there continuity?
I s t he r ev er se l ock out sol enoi d OK ?
08/08/21 14:46:39 61SNR030_130_0077
ProCarManuals.com
DYNOMITE -2009-


(#'



)
Î
(#'



")
13-7713-77
Reverse Lockout Solenoid Test Reverse Lockout Solenoid Disassembly/Reassembly
REVERSE LOCKOUT SOLENOID
2P CONNECTOR
A
1. Remove the reverse lockout solenoid (see page13-77).
2. Connect battery positive terminal to the r everse
lockout solenoid 2P connector No. 2 terminal, and
connect the battery negative terminal to the No. 1
terminal.
3. Make sure the reverse lockout solenoid works. If the reverse lockout solenoid does not work, replace
it. 1. Do the battery removal procedure (see page 22-69).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the battery base (see step 4 on page 13-84).
4. Disconnect the output shaft (countershaft) speed
sensor connector, the back-up light switch
connector, and the r everse lockout solenoid
connector (see step 6 on page 13-84).
5. Carefully remove the shift cables and the cable bracket together to avoid bending the cables (see
step 7 on page 13-85).
6. Remove the reverse lockout solenoid (A).
(cont’d)
Terminal side of male terminals
08/08/21 14:46:40 61SNR030_130_0079
ProCarManuals.com
DYNOMITE -2009-

Î
13-78Reverse Lockout System
Reverse Lockout Solenoid Disassembly/Reassembly (cont’d)
C
B
A
6x1.0mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
A
7. Remove the roller (A), the select lock return spring
(C), and select lock cam B.
8. Install the components of the r everse lockout
solenoid in the reverse order of removal.
9. Clean any dirt and oil from the mating surface of the reverse lockout solenoid and the change lever
assembly.
10. Apply liquid gasket, P/N 08718-0001 evenly to the change lever assembly mating surface of the
reverse lockout solenoid. Install the com ponent
within 5 minutes of applying the liquid gasket.
NOTE:  If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket. 11. Install the reverse lockout solenoid (A).
12. Install the cable bracket and the shift cables (see
step 37 on page 13-97).
13. Connect the r everse lockout solenoid connector,
the back-up light switch connector, and the output
shaft (countershaft) speed sensor connector (see
step 39 on page 13-97).
14. Install the battery base (see step 41 on page 13-98).
15. Install the air cleaner assembly (see page 11-345).
16. Do the battery installation procedure (see page 22-69).
08/08/21 14:46:40 61SNR030_130_0080
ProCarManuals.com
DYNOMITE -2009-

Ì
Ï



(#'

 )
Special Tools Required
13-84
Manual Transmission
Transmission Removal
A
B C
D
A A
B
D
C
A
B
 Engine hanger adapter VSB02C000015
 2006 Civic engine hanger VSB02C000025
 Engine support hanger, A and Reds AAR-T 1256
 Front subframe adapter VSB02C000016
These special tools are available through the Acura
Canada Technical Tools Department; FAX
866-398-8665/e-mail: ch_technicaltools ch.honda.com
NOTE: Use fender covers to avoid damaging painted
surfaces.
1. Do the battery removal procedure (see page 22-69).
2. Remove the cowl cover and the under-cowl panel (see page 20-163).
3. Remove the air cleaner assembly (see page 11-345).
4. Remove the harness clips (A) and the intake air duct (B), then remove the battery base (C) with the
coolant reservoir (D). 5. Remove the clutch line bracket (A), then carefully
move the slave cylinder (B) out of the way to avoid
bending the clutch line.
NOTE: Do not press the clutch pedal after the slave
cylinder has been moved.
6. Disconnect the back-up light switch connector (A), the output shaft (countershaft) speed sensor
connector (B), the r everse lockout solenoid
connector (C), and the harness clips (D).
08/08/21 14:47:19 61SNR030_130_0086
ProCarManuals.com
DYNOMITE -2009-



13-98Manual Transmission
Transmission Installation (cont’d)
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
(P/N 08798-9002) B
A
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) 6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) B
A
C
C
D
40. Apply super high temp urea grease (P/N 08798-
9002) to the end of the slave cylinder pushrod.
Install the slave cylinder (A), then install the clutch
line bracket (B). Be careful not to bend the clutch
line.
41. Install the battery base (A) with the coolant reservoir (B). 42. Install the harness clips (C) and the intake air duct
(D).
43. Install the air cleaner assembly (see page 11-345).
44. Do the battery installation procedure (see page 22-69).
45. Install the under-cowl panel and the cowl cover (see page 20-163).
46. Check the shift lever and the clutch operation.
47. Check the wheel alignment (see page 18-5).
48. Test-drive the vehicle.
08/08/21 14:47:31 61SNR030_130_0100
ProCarManuals.com
DYNOMITE -2009-

Î
ØÚÓ´
µ
Electronic Control System (cont’d)
PCM A/T Control System Electrical Connections
14-48 Automatic Transmission
System Description (cont’d)
41
23
41 24
23 4
40
29
26 2
27
20 21
10
89
35 19
16 17 18
36 39 40 44434230
29 32 16 1817
13 14 15
1211 789
654321
31
36 37 4044
42
27 28 29
33 3424 25
20 21 14 15
654
31 23
31
13
9
87
11 12 1514 13 17 18
16
22
21
20 25
32 35 34
33
3028
27
42 43 44
36 22
39
10
26
SHE
B24
RIGHT SUPP
B16
B40
SDNP
LEFT
F-CAN Transceiver
CANL
A37
CANH
A36
Terminal side of female terminals
A (44P) B (44P) C (44P) C44 C40 B1 B36
B15
ATPS
S
Dash-light Brightness Control Circuit
SG1C14
NC C43
VCC1 C13
B33
SG2 B17
NM B18
VCC2
TATF B27 B11
SHB SHA B10
B20
SHC
B26
SHD LSC
B25 B35
LSB
PG1
B28
ATPFWD
N BAT
D
PG2
ATPP
B13
DATA LINK CONNECTOR
R
CPU
LG1
ATPR
B14 SCS
IGNITION SWITCH
LG2
GAUGE CONTROL MODULE (TACH)
B9OP3SW OP2SW
B8 ATPRVS
B22 ATPD
B12
P
S
R
P
ND B21ATPN
BKSW
A40
BRAKE LIGHTS A31 A27SLS PCM
C36 IG1 B44
LSA
BATTERY
IG1
BRAKE PEDAL
POSITION SWITCH SHIFT LOCK
SOLENOID
TRANSMISSION
RANGE SWITCH A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE A
A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE B
A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE C
SHIFT SOLENOID
VALVE A
SHIFT SOLENOID
VALVE B
SHIFT SOLENOID
VALVE C
SHIFT SOLENOID
VALVE D
ATF
TEMPERATURE
SENSOR
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED
SENSOR
INPUT SHAFT
(MAINSHAFT)
SPEED
SENSOR
2ND CLUTCH TRANSMISSION
FLUID PRESSURE SWITCH
3RD CLUTCH TRANSMISSION
FLUID PRESSURE SWITCH
A/T Gear Position Indicator
Driver Circuit
SHIFT
INDICATOR SHIFT SOLENOID
VALVE E
PADDLE SHIFTER (UPSHIFT SWITCH)
PADDLE SHIFTER (DOWNSHIFT SWITCH)
PCM Connector Terminal Locations
08/08/21 14:38:25 61SNR030_140_0050
ProCarManuals.com
DYNOMITE -2009-