Page 1667 of 5135

05BAA±01
05±1634
±
DIAGNOSTICS THEFT DETERRENT SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
PROBLEM SYMPTOMS TABLE
Proceed to the reference page shown in the table below for each malfunction sym\
ptom and troubleshoot
each circuit.
HINT:
Troubleshooting of the theft deterrent system is based on the premise that the door loc\
k control system and
the wireless door lock control system are operating normally. Accordingly, before troubleshooting the theft
deterrent system, first make certain that the door lock control system and the wireless door lock control sys-
tem are operating normally.
SymptomSuspected AreaSee Page
Theft deterrent system cannot be set
1. Security indicator circuit
2. ECU power source circuit
3. Unlock warning switch circuit
4. Door key lock and unlock switch
5. Luggage compartment door key lock and unlock switch (Sedan)
6. Back door key lock and unlock switch (Liftback, Wagon)
7. Door courtesy switch circuit
8. Luggage compartment door courtesy switch circuit (Sedan)
9. Back door courtesy switch circuit (Liftback, Wagon)
10.Engine hood courtesy switch circuit05±1635
05±1637
05±1594 73±3
73±3
73±3
05±1631
05±1631
05±1631
05±1642
Security indicator does not blink when theft deterrent system is
set1. Security indicator circuit05±1635
Alarm sounding state is not canceled when ignition switch is
turned ON±OFF 10 times within 15 seconds1. Ignition switch circuit
2. Unlock warning switch circuit05±1639
05±1594
Theft deterrent system can be set even when any door is open
1. Door courtesy switch circuit
2. Luggage compartment door courtesy switch circuit (Sedan)
3. Back door courtesy switch circuit (Liftback, Wagon)05±1631
05±1631
05±1631
Horns (low pitched, high pitched) do not sound while theft deter-
rent system is in warning operation1. Horn (low pitched, high pitched) circuit05±1644
Hazard warning lamps do not flash while theft deterrent system is
in warning operation1. Hazard warning circuit65±5
Room lamp does not flash while theft deterrent system is in warn-
ing operation1. Room lamp circuit65±5
Theft warning siren sounds even when theft deterrent system is
not set1. Theft warning siren circuit05±1647
Hazard warning lamps flash even when theft deterrent system is
not set1. Hazard warning switch circuit65±5
Room lamp flashes even when theft deterrent system is not set1. Room lamp circuit65±5
Theft warning siren sounds even when theft deterrent system is
not set1. Theft warning siren circuit05±1647
Intrusion (theft warning) sensor does not detect any moving object
while theft deterrent system is set1. Instrution sensor circuit05±1650
Intrusion (theft warning) sensor sets off alarm while theft deterrent
system is not set or there is nothing moving inside vehicle with
theft deterrent system set
1. Intrusion sensor circuit05±1650
Intrusion (theft warning) sensor OFF switch does not operate1. Intrusion sensor circuit05±1650
Intrusion (theft warning) sensor OFF switch continues operating1. Intrusion sensor circuit05±1650
Page 1675 of 5135

B66227
E10
ECMT8
Transponder Key ECU Assy
IMI
IMO30*
1
27*2
29*1
26*2W GR
6
7EFIO
EFII
*1: 1CD±FTV
*2: Gasoline
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
05±1625
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2799 ENGINE IMMOBILISER SYSTEM
MALFUNCTION
CIRCUIT DESCRIPTION
This DTC is output when the ECM detects errors in communication between the transponder key ECU assy
and the ECM or in the communication lines.
This DTC is also output when an engine start is attempted while the ECU communication ID between the
transponder key ECU and the ECM are different.
Before troubleshooting for this DTC, make sure that there is no DTC detected in the transponder key ECU.
If there is a key code±related DTC detected in the transponder key ECU, repair it first.
DTC No.DTC Detection ConditionTrouble Area
B2799
Error in communication between ECM and transponder
key ECU, and in communication line
Communication ID is different during communication with
transponder key ECUWire harness
Transponder key ECU assy
Transponder key amplifier
ECM
WIRING DIAGRAM
05B0J±03
Page 1677 of 5135
B52550
I12
Transponder Key AmplifierT8
Transponder Key ECU Assy
Y±G
CODE
411CODE
05±1624
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2797 COMMUNICATION MALFUNCTION NO.1
CIRCUIT DESCRIPTION
This DTC is output when an error occurs in normal communication.
HINT:
Some noise is found in the communication line.
DTC No.DTC Detection ConditionTrouble Area
B2797Keys are positioned too close to each other or noise oc-
curred in communication line
Key
Wire harness
Transponder key amplifier
Transponder key ECU assy
WIRING DIAGRAM
INSPECTION PROCEDURE
1 CHECK OPERATION OF TRANSPONDER KEY AMPLIFIER
(a) After replacing the transponder key amplifier, check that the engine starts.
OK NORMAL
(TRANSPONDER KEY AMPLIFIER DEFECTIVE)
NG
REPLACE TRANSPONDER KEY ECU ASSY
05B0I±03
Page 1678 of 5135
B62676
I12
Transponder Key AmplifierT8
Transponder Key ECU Assy
VC5
CODE
TXCT
AGND Y±B
Y±G
L±R
GR±R8
11
12
13 1
4
5
7 TXCT
GND
ANT2 ANT1 VC5
CODE
CoilAmplifier
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
05±1621
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2796 NO COMMUNICATION IN IMMOBILISER
SYSTEM
DTC B2798 COMMUNICATION MALFUNCTION NO.2
CIRCUIT DESCRIPTION
This code is stored in the memory when a key that does not have a transponder chip is inserted or if commu-
nication between the key and transponder key ECU is impossible.
DTC No.DTC Detection ConditionTrouble Area
B2796No communication
Key
Wire harness
Transponder key amplifier (Transponder key coil)
Transponder key ECU assy
B2798Communication errorKey
WIRING DIAGRAM
05B0H±03
Page 1681 of 5135
05±1620
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2795 UNMATCHED KEY CODE
CIRCUIT DESCRIPTION
This DTC is output when a key with a key code that has not been registered in the ECU is inserted into the
ignition key cylinder.
DTC No.DTC Detection ConditionTrouble Area
B2795Key with unregistered key code is insertedKey
INSPECTION PROCEDURE
1 DELETE DTC AND INSERT ALL PRESENTLY AVAILABLE KEYS TO CHECK
WHETHER ENGINE STARTS OR NOT
OK NO PROBLEM
(BECAUSE OF KEY RE±REGISTRATION)
NG
REPLACE KEY THAT WILL NOT START ENGINE
05B0G±03
Page 1682 of 5135
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
05±1619
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2794 UNMATCHED ENCRYPTION CODE
CIRCUIT DESCRIPTION
This DTC is output when a key with an incomplete key code is inserted into the ignition key cylinder.
DTC No.DTC Detection ConditionTrouble Area
B2794Key with incomplete key code is insertedKey
INSPECTION PROCEDURE
1 REPLACE KEY
05B0F±03
Page 1683 of 5135
05±1618
±
DIAGNOSTICS ENGINE IMMOBILISER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2793 TRANSPONDER CHIP MALFUNCTION
CIRCUIT DESCRIPTION
This DTC is output when a malfunction is found in a key during the key code \
registration or the key code
is not registered normally. Replace the key when the key code registration is not performed normal\
ly and
this DTC is detected.
DTC No.DTC Detection ConditionTrouble Area
B2793Transponder chip malfunction Key
INSPECTION PROCEDURE
1 CHECK DTC
(a)Delete the DTC (See page 05±1602).
(b) Insert the key into the ignition key cylinder.
(c) Check that no code is output.
OK NO PROBLEM
NG
2 RE±REGISTER KEY
(a)Delete the DTC (See page 05±1602).
(b) Re±register the key and check that the engine starts with the key. OK NORMAL
NG
REPLACE KEY
05B0E±03
Page 1684 of 5135

B62676
I12
Transponder Key AmplifierT8
Transponder Key ECU Assy
VC5
CODE
TXCT
AGND Y±B
Y±G
L±R
GR±R8
11
12
13 1
4
5
7 TXCT
GND
ANT2 ANT1 VC5
CODE
CoilAmplifier
05±1616
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DTC B2784 ANTENNA COIL OPEN/SHORT
CIRCUIT DESCRIPTION
The transponder key coil is built into the transponder key amplifier and receives a key code signal from the
transponder chip in the key. This signal is amplified by the amplifier and then output to the transponder key
ECU.
DTC No.DTC Detection ConditionTrouble Area
B2784Antenna coil is open/short
Wire harness
Transponder key amplifier
Transponder key ECU assy
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 READ VALUE OF HAND±HELD TESTER
(IMMOBILISER ECU (TRANSPONDER KEY ECU ASSY) (SWITCH CONDITION))
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON with the key that will not start the engine.
(c) Select the item ANTENNA COIL on the hand±held tester.
OK: NORMAL
NG: FAIL
OK CHECK AND REPLACE TRANSPONDER KEY
ECU ASSY
NG
05B0D±03