2005 TOYOTA AVENSIS air suspension

A79140
−
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1CD −FTV)(From September,
2003)14 −11 1
AVENSIS Supplement (RM1045E)
30. REMOVE CLUTCH ACCUMULATOR ASSY (See Pub. No. RM1018E on page 42 −22)
SST 09023 −00100
31. REMOVE CLUTCH RELEASE CYLINDER ASSY (See Pub. No. RM1018E on page 42 −17)
32. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See Pub. No. RM1018E on page 14 −269)
33. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (W/ AIR CONDITIONING)
(See Pub. No. RM1018E on page 55 −86)
HINT:
Secure the hoses off to the side instead of detaching.
34. REMOVE FLOOR PANEL BRACE FRONT (See page 15 −6)
35. REMOVE EXHAUST PIPE ASSY FRONT (See page 15 −6)
36. SEPARATE RETURN TUBE SUB −ASSY
(a) Remove the 2 clamp bolts, then separate the return tube
sub−assembly.
37. SEPARATE VANE PUMP OIL RESERVOIR ASSY
38. REMOVE FRONT AXLE HUB LH NUT (See Pub. No. RM1018E on page 30 −6)
SST 09930 −00010
HINT:
Perform the same procedure as above on the opposite side.
39. SEPARATE TIE ROD END SUB −ASSY LH (See Pub. No. RM1018E on page 30 −6)
SST 09628 −62011
HINT:
Perform the same procedure as above on the opposite side.
40. SEPARATE FRONT STABILIZER LINK ASSY LH (See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
41. REMOVE COLUMN HOLE COVER SILENCER SHEET
(a) Remove the 2 clips and column hole cover silencer sheet.
42. REMOVE STEERING COLUMN HOLE COVER SUB −ASSY NO.1
43. REMOVE STEERING INTERMEDIATE SHAFT ASSY NO.2 (See Pub. No. RM1018E on page 51 −36)
44. SEPARATE FRONT SUSPENSION ARM SUB −ASSY LOWER NO.1 LH
(See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
45. SEPARATE FRONT AXLE ASSY LH (See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.

A93403
2to7mm
(0.0787 to
0.2756 in.)0to4mm
(0 to
0.1575 in.)
Intake Shutter Side:
Air Hose No. 3 Side:
4to12mm
(0.1575 to
0.4724 in.)
14
−132
−
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1CD −FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
191. INSTALL FRONT AXLE ASSY LH (See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
192. INSTALL FRONT SUSPENSION ARM SUB −ASSY LOWER NO.1 LH
(See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
193. INSTALL STEERING INTERMEDIATE SHAFT ASSY NO.2
(See Pub. No. RM1018E on page 51 −36)
194. INSTALL FRONT STABILIZER LINK ASSY LH (See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
195. INSTALL TIE ROD END SUB −ASSY LH (See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
196. INSTALL FRONT AXLE HUB LH NUT (See Pub. No. RM1018E on page 30 −6)
HINT:
Perform the same procedure as above on the opposite side.
197. INSTALL RETURN TUBE SUB −ASSY
Torque: 8.0 N
m (82 kgf
cm, 71 in.
lbf)
198. INSTALL EXHAUST PIPE ASSY FRONT (See page 15 −6)
199. INSTALL FLOOR PANEL BRACE FRONT (See page 15 −6)
200. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (W/ AIR CONDITIONING) (See Pub. No. RM1018E on page 55 −86)
201. ADJUST V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM1018E on page 14 −269)
202. INSTALL CLUTCH RELEASE CYLINDER ASSY (See Pub. No. RM1018E on page 42 −17)
203. INSTALL CLUTCH ACCUMULATOR ASSY (See Pub. No. RM1018E on page 42 −22)
SST 09023 −00100
204. INSTALL AIR TUBE NO.2
(a) Install the air hose and 2 hose clamps as shown in the il-lustration.

A64005
A76715
– ENGINE MECHANICALPARTIAL ENGINE ASSY (1ZZ–FE/3ZZ–FE)(From
February, 2004)14–13
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
49. REMOVE FRONT AXLE HUB RH NUT
SST 09930–00010
HINT:
Perform the same procedure as above on the opposite side.
50. SEPARATE TIE ROD END SUB–ASSY LH (See Pub. No. RM1018E on page 30–6)
SST 09628–62011
51. SEPARATE TIE ROD END SUB–ASSY RH
SST 09628–62011
HINT:
Perform the same procedure as above on the opposite side.
52. SEPARATE FRONT STABILIZER LINK ASSY LH (See Pub. No. RM1018E on page 30–6)
53. SEPARATE FRONT STABILIZER LINK ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
54. SEPARATE FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 LH
(See Pub. No. RM1018E on page 30–6)
55. SEPARATE FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 RH
HINT:
Perform the same procedure as above on the opposite side.
56. SEPARATE FRONT AXLE ASSY LH (See Pub. No. RM1018E on page 30–6)
57. SEPARATE FRONT AXLE ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
58. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
(a) Set the engine lifter.
(b) Remove the 4 bolts and 2 nuts, then detach the engine
mounting insulator.
(c) Remove the through bolt and nut, then detach the engine
mounting insulator from the vehicle.

A76717
A76716
A62830Front SideRear Side
A76718
14–14– ENGINE MECHANICALPARTIAL ENGINE ASSY (1ZZ–FE/3ZZ–FE)(From
February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
(d) Remove the 2 bolts and 2 nuts as shown in the illustration.
(e) Remove the 8 bolts and front suspension member brace
rear RH and LH.
(f) Carefully remove the engine with transaxle from the en-
gine compartment.
(g) Install the engine hanger No. 1 (12281–15040) and bolt
(91512–B1016).
Torque: 38 N⋅m (387 kgf⋅cm, 28 ft⋅lbf)
(h) Install the engine hanger (12281–22021) and bolt
(91512–B1016).
Torque: 38 N⋅m (387 kgf⋅cm, 28 ft⋅lbf)
HINT:
Securely install the front engine hanger (12281–22021) and
rear engine hanger No. 1 (12281–15040) onto the engine as-
sembly.
(i) Attach the engine sling, then hang the engine with the
chain block.
59. REMOVE FRONT SUSPENSION CROSSMEMBER
W/CENTER MEMBER
(a) Remove the through bolt and nut, then detach the engine
mounting insulator FR from the engine mounting bracket.

A76719
A62838SST
A62838SST
A76713
– ENGINE MECHANICALPARTIAL ENGINE ASSY (1ZZ–FE/3ZZ–FE)(From
February, 2004)14–15
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
(b) Remove the through bolt, then detach the engine mount-
ing insulator RR from the suspension crossmember.
(c) Separate the engine and the transaxle assembly from the
suspension crossmember and engine mounting member.
60. REMOVE STARTER ASSY (See Pub. No. RM1018E on page 19–3)
61. REMOVE MANUAL TRANSAXLE ASSY (M/T TRANSAXLE)
(See Pub. No. RM1018E on page 41–15)
62. REMOVE AUTOMATIC TRANSAXLE ASSY (A/T TRANSAXLE)
(See Pub. No. RM1018E on page 40–11)
63. REMOVE CLUTCH COVER ASSY (M/T TRANSAXLE) (See Pub. No. RM1018E on page 42–26)
64. REMOVE CLUTCH DISC ASSY (M/T TRANSAXLE) (See Pub. No. RM1018E on page 42–26)
65. REMOVE FLYWHEEL SUB–ASSY (M/T TRANSAXLE)
(a) Hold the crankshaft with SST, then remove the 8 bolts and
flywheel.
SST 09960–10010 (09962–01000, 09963–01000)
66. REMOVE DRIVE PLATE & RING GEAR SUB–ASSY
(A/T TRANSAXLE)
(a) Hold the crankshaft with SST, then remove the 8 bolts and
drive plate & ring gear.
SST 09960–10010 (09962–01000, 09963–01000)
67. REMOVE IGNITION COIL ASSY
(a) Disconnect the 4 ignition coil connectors.
(b) Remove the 2 nuts which are used to secure the engine
wire.

A76719
A76718
A76717
A76717
A
B
A
B 14–24
– ENGINE MECHANICALPARTIAL ENGINE ASSY (1ZZ–FE/3ZZ–FE)(From
February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
114. INSTALL CLUTCH DISC ASSY (M/T TRANSAXLE) (See Pub. No. RM1018E on page 42–26)
SST 09301–00210
115. INSTALL CLUTCH COVER ASSY (M/T TRANSAXLE) (See Pub. No. RM1018E on page 42–26)
SST 09301–00210
116. INSTALL MANUAL TRANSAXLE ASSY (M/T TRANSAXLE)

(See Pub. No. RM1018E on page 41–15)
117. INSTALL AUTOMATIC TRANSAXLE ASSY (A/T TRANSAXLE)
(See Pub. No. RM1018E on page 40–11)
118. INSTALL STARTER ASSY (See Pub. No. RM1018E on page 19–3)
119. INSTALL FRONT SUSPENSION CROSSMEMBER
W/CENTER MEMBER
(a) Attach the engine and transaxle assembly to the suspen-
sion crossmember and engine mounting member.
(b) Install the bolt which is used to secure the rear engine
mounting bracket onto the mounting insulator.
Torque: 87 N⋅m (887 kgf⋅cm, 64 ft⋅lbf)
(c) Install the bolt which is used to secure the front engine
mounting bracket onto the mounting insulator.
Torque: 52 N⋅m (530 kgf⋅cm, 38 ft⋅lbf)
120. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
SST 09670–00010
(a) Set the engine assembly with transaxle on the engine lift-
er.
(b) Temporarily install the suspension crossmember with the
2 bolts and 2 nuts.
(c) Install the engine mounting insulator LH.
Torque: 80 N⋅m (816 kgf⋅cm, 59 ft⋅lbf)
(d) Install the engine mounting insulator RH.
Torque: 52 N⋅m (530 kgf⋅cm, 38 ft⋅lbf)
(e) Tighten the 2 bolts and 2 nuts.
Torque:
45 N⋅m (459 kgf⋅cm, 33 ft⋅lbf) for bolt A
133 N⋅m (1,356 kgf⋅cm, 98 ft⋅lbf) for nut B

A76716
AA
BBBBB
B
A76714
– ENGINE MECHANICALPARTIAL ENGINE ASSY (1ZZ–FE/3ZZ–FE)(From
February, 2004)14–25
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
(f) Install the front suspension member brace LH and RH
with the 8 bolts.
Torque:
133 N⋅m (1,356 kgf⋅cm, 98 ft⋅lbf) for bolt A
80 N⋅m (816 kgf⋅cm, 59 ft⋅lbf) for bolt B
121. INSTALL FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 LH
(See Pub. No. RM1018E on page 30–6)
122. INSTALL FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 RH
HINT:
Perform the same procedure as above on the opposite side.
123. INSTALL FRONT STABILIZER LINK ASSY LH (See Pub. No. RM1018E on page 30–6)
124. INSTALL FRONT STABILIZER LINK ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
125. INSTALL TIE ROD END SUB–ASSY LH (See Pub. No. RM1018E on page 30–6)
126. INSTALL TIE ROD END SUB–ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
127. INSTALL FRONT AXLE HUB LH NUT (See Pub. No. RM1018E on page 30–6)
128. INSTALL FRONT AXLE HUB RH NUT
HINT:
Perform the same procedure as above on the opposite side.
129. INSTALL EXHAUST PIPE ASSY FRONT (See Pub. No. RM1018E on page 15–2)
130. INSTALL FLOOR PANEL BRACE FRONT
Torque: 30 N⋅m (306 kgf⋅cm, 22 ft⋅lbf)
131. INSTALL STEERING INTERMEDIATE SHAFT (See Pub. No. RM1018E on page 50–9)
132. INSTALL GENERATOR ASSY (See Pub. No. RM1018E on page 19–7)
133. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (W/ AIR CONDITIONING)
HINT:
1ZZ–FE (See Pub. No. RM1018E on page 55–74)
3ZZ–FE (See Pub. No. RM1018E on page 55–70)
134. INSTALL CLUTCH RELEASE CYLINDER ASSY (M/T TRANSAXLE)

(See Pub. No. RM1018E on page 41–15)
135. INSTALL FLOOR SHIFT CABLE TRANSMISSION CONTROL SHIFT (A/T TRANSAXLE)
(See Pub. No. RM1018E on page 40–11)
136. INSTALL BATTERY CARRIER
(a) Install the battery carrier and bracket with the 4 bolts.
Torque: 13 N⋅m (131 kgf⋅cm, 9 ft⋅lbf)