2005 SUZUKI GRAND VITARA Service Workshop Manual

YH4
GRAND
VITARA
L
LH : Left Hand
LSPV : Load Sensing Proportioning
Valve
M
MAF Sensor : Mass Air Flow Sensor
(Air Flow Sensor, AFS, Air
Flow Meter, AFM)
MAP Sensor : Manifold Absolute Pressure
Sensor (Pressure Sensor, PS)
Max : Maximum
MFI : Multiport Fuel Injection
(Multipoint Fuel Injection)
Min : Minimum
MIL : Malfunction Indicator Lamp
(ªCHECK ENGINEº Light)
M / T : Manual Transmission
N
NOx : Nitrogen Oxides
O
OBD : On-Board Diagnostic System
(Self-Diagnosis Function)
O / D : Overdrive
OHC : Over Head Camshaft
P
PNP : Park / Neutral Position
P / S : Power Steering
PSP Switch : Power Steering Pressure
Switch (P / S Pressure Switch)
PCM : Powertrain Control Module
PCV : Positive Crankcase Ventilation
R
RH : Right Hand
S
SAE : Society of Automotive
Engineers
SDM : Sensing and Diagnostic
Module (Air bag controller,
Air bag control module)
SFI : Sequential Multiport Fuel
Injection
SOHC : Single Over Head Camshaft
T
TBI : Throttle Body Fuel Injection
(Single-Point Fuel Injection,
SPI)
TCC : Torque Converter Clutch
TCM : Transmission Control Module
(A / T Controller, A / T Control
Module)
TP Sensor : Throttle Position Sensor
TVV : Thermal Vacuum Valve
(Thermal Vacuum Switching
Valve, TVSV, Bimetal Vacuum
Switching Valve, BVSV)
TWC : Three Way Catalytic
Converter (Three Way
Catalyst)
2WD : 2 Wheel Drive
V
VIN : Vehicle Identification
Number
VSS : Vehicle Speed Sensor
W
WU-OC : Warm Up Oxidation
Catalytic Converter
WU-TWC : Warm Up Three Way
Catalytic Converter
0A-22 GENERAL INFORMATION

YH4
GRAND
VITARA
METRIC BOLTS±IDENTIFICATION CLASS NUMBERS
OR MARKS CORRESPOND TO BOLT
STRENGTH±INCREASING NUMBERS REPRESENT
INCREASING STRENGTH.NUT STRENGTH
IDENTIFICATION
GENERAL INFORMATION 0A-23
METRIC INFORMATION
METRIC FASTENERS
Most of the fasteners used for this vehicle are metric fasteners.
When replacing any fasteners, it is most important that replacement
fasteners be the correct diameter, thread pitch and strength.
FASTENER STRENGTH IDENTIFICATION
Most commonly used metric fastener strength property classes are
4T, 6.8, 7T, 8.8 and radial line with the class identification embossed
on the head of each bolt. Some metric nuts will be marked with
punch, 6 or 8 mark strength identification on the nut face. Figure
shows the different strength markings.
When replacing metric fasteners, be careful to use bolts and nuts
of the same strength or greater than the original fasteners (the
same number marking or higher). It is likewise important to select
replacement fasteners of the correct diameter and thread pitch.
Correct replacement bolts and nuts are available through the parts
division.

YH4
GRAND
VITARA
0A-24 GENERAL INFORMATION
Self-lock
nut
STANDARD TIGHTENING TORQUE
Each fastener should be tightened to the torque specified in each section of this manual. If no description or specifi-
cation is provided, refer to the following tightening torque chart for the applicable torque for each fastener. When
a fastener of greater strength than the original one is used, however, use the torque specified for the original fasten-
er.
NOTE:

For the flanged bolt, flanged nut and self-lock nut of 4T and 7T strength, add 10% to the tightening torque
given in the chart below.

The chart below is applicable only where the fastened parts are made of steel or light alloy.
Tightening torque chart
Thread Diameter (Nominal Diameter)
(mm)
45681012141618
Strength
45681012141618
A equivalent of 4T strength
fastenerN.m1.53.05.513294565105160
kg-m0.150.300.551.32.94.56.510.516
lb-ft1.02.54.09.521.032.547.076.0116.0
A equivalent of 6.8 strength
fastener without flan
geN.m2.44.78.4204280125193280g
kg-m0.240.470.842.04.28.012.519.328
lb-ft2.03.56.014.530.558.090.5139.5202.5
A equivalent of 6.8 strength
fastener with flan
geN.m2.44.98.8214484133203298g
kg-m0.240.490.882.14.48.413.320.329.8
lb-ft2.03.56.515.532.061.096.5147.0215.5
A equivalent of 7T strength
fastenerN.m2.34.510235085135210240
kg-m0.230.451.02.35.08.513.52124
lb-ft2.03.57.517.036.561.598.0152.0174.0
A equivalent of 8.8 strength
fastener without flan
geN.m3.16.3112756105168258373g
kg-m0.310.631.12.75.610.516.825.837.3
lb-ft2.54.58.019.540.576.0121.5187.0270.0
A equivalent of 8.8 strength
fastener with flan
geN.m3.26.512295911 3175270395g
kg-m0.320.651.22.95.911.317.52739.5
lb-ft2.55.09.021.043.082.0126.5195.5286.0

YH4
GRAND
VITARA
0B
MAINTENANCE AND LUBRICATION 0B-1
SECTION 0B
MAINTENANCE AND LUBRICATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
MAINTENANCE SCHEDULE0B - 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Schedule Under Normal Driving Conditions 0B - 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Recommended Under Severe Driving Conditions 0B - 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE0B - 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine0B - 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition System0B - 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel System0B - 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emission Control System0B - 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis and Body0B - 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Final Inspection0B - 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RECOMMENDED FLUIDS AND LUBRICANTS0B - 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE UNDER NORMAL DRIVING CONDITIONS
Interval:
This interval should be judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
ENGINE
1-1. Drive beltV-beltIRIRIR
V-rib belt (Flat type)±±I±±R
1-2. Camshaft timing belt (G16 engine only)Replace every 100,000 km or
60,000 miles
1-3. Valve lash (clearance)G16 engine only±I±I±I
1-4. Engine oil and
oil filterJ20 / H25 engines
G16 engine with HO2S (SG, SH, SJ)RRRRRR
G16 engine with HO2S (SE, SF),
G16 engine without HO2SReplace every 10,000 km (6,000 miles)
or 8 months
1-5. Engine coolant±±R±±R
1-6. Exhaust system±I±I±I
IGNITION SYSTEM
2-1. Spark plugs
Wh
Vehicle without
HO2S
Nickel plug±R±R±R
When
unleaded
HO2SIridium plug±±±R±±unleaded
fuel isVehicle with
HO2S
Nickel plug±±R±±Rfuel is
usedHO2SIridium plugReplace every 105,000 km or 63,000
miles
When leaded fuel is used, refer to ªSevere Driving Conditionº schedule
FUEL SYSTEM
3-1. Air cleaner filterIIRIIR
3-2. Fuel lines and connections±I±I±I
3-3. Fuel filterReplace every 105,000 km or 63,000
miles
3-4. Fuel tank±±I±±I
EMISSION CONTROL SYSTEM
4-1. Crankcase ventilation hoses and connections
(Vehicle without HO2S)±±I±±I
4-2. PCV valveVehicle without HO2S±±I±±I
Vehicle with HO2S±±±±±I
4-3. Fuel evaporative emission
tl t
Vehicle without HO2S±I±I±I
control systemVehicle with HO2S±±±±±I
NOTES:

ªRº : Replace or change

ªIº : Inspect and correct, replace or lubricate if necessary

For Item 1-2. Camshaft timing belt: This belt may be replaced every 90,000 km (54,000 miles) according
to customer's maintenance convenience.

For Sweden, item 2-1, 4-2 and 4-3 should be performed by odometer reading only.

For Item 2-1. Spark plugs, replace every 50,000 km if the local law requires.

Nickel spark plug: BKR6E-11 or K20PR-U11

Iridium spark plug: IFR6E11 or SK20PR-A11 for G16 engine, IFR5J11 or SK16PR11 for J20 / H25 engines

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-3
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
CHASSIS AND BODY
6-1. Clutch (pedal and fluid level)±I±I±I
6-2.Brake discs and pads (thickness, wear, damage)IIIIII
Brake drums and shoes (wear, damage) ±I±I±I
6-3. Brake hoses and pipes (leakage, damage, clamp)±I±I±I
6-4. Brake fluid±R±R±R
6-5. Brake lever and cable (damage, stroke, operation)Inspect at first 15,000 km (9,000 miles)
only
6-6. Tires (wear, damage, rotation)IIIIII
6-7. Wheel discs (damage)IIIIII
6-8. Suspension system (tighteness, damage, rattle, breakage)±I±I±I
6-9. Propeller shafts and drive shafts±±I±±I
6-10. Manual transmission oil (leakage, level)
(I: 1st 15,000 km only)I±R±±R
6-11. Automatic transmissionFluid level±I±I±I
Fluid changeReplace every 165,000 km
(99,000 miles)
Fluid hose±±±R±±
6-12. Transfer oil (leakage, level)I±I±I±
6-13. Differential oil (leakage, level) (R: 1st 15,000 km only)R or I±I±I±
6-14. Steering system (tighteness, damage, breakage, rattle)±I±I±I
6-15. Power steering (if equipped)IIIIII
6-16. All latches, hinges and locks±I±I±I
6-17. Air conditioning filter (if equipped)±IR±IR
NOTES:
ªRº : Replace or change
ªIº : Inspect and correct, replace or lubricate if necessary

YH4
GRAND
VITARA
0B-4 MAINTENANCE AND LUBRICATION
MAINTENANCE RECOMMENDED UNDER SEVERE DRIVING CONDITIONS
If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is
recommended that applicable maintenance operation be performed at the particular interval as given in the chart
below.
Severe condition code
A ± Repeated short trips E ± Repeated short trips in extremely
B ± Driving on rough and / or muddy roads cold weather
C ± Driving on dusty roads F ± Leaded fuel use
D ± Driving in extremely cold weather G ± ± ± ± ± ± ± ± ±
and / or salted roads H ± Trailer towing (if admitted)
Severe
Condition Code
MaintenanceMaintenance
OperationMaintenance Interval
BCDITEM 1-1IEvery 15,000 km
(9,000 miles) or 12 months
± B C D ± ± ± ±Drive belt (V-rib belt)REvery 45,000 km
(27,000 miles) or 36 months
A ± C D E F ± HITEM 1-4
Engine oil and oil filterREvery 5,000 km
(3,000 miles) or 4 months
± B ± ± ± ± ± ±ITEM 1-6
Exhaust pipe mountingsIEvery 15,000 km
(9,000 miles) or 12 months
CITEM 3-1IEvery 2,500 km
(1,500 miles)
± ± C ± ± ± ± ±Air cleaner filter*1REvery 30,000 km
(18,000 miles) or 24 months
ABC EF HITEM 2-1Nickel plugREvery 10,000 km
(6,000 miles) or 8 months
A B C ± E F ± HSpark plugsIridium plugREvery 30,000 km
(18,000 miles) or 24 months
± B ± D E ± ± HITEM 6-9
Propeller shafts and drive shaftsIEvery 15,000 km
(9,000 miles) or 12 months
± B ± ± E ± ± H
ITEM 6-10, 6-12, 6-13
Manual transmission,
transfer and differential oil
REvery 30,000 km
(18,000 miles) or 24 months
± B ± ± E ± ± HITEM 6-11
Automatic transmission fluidREvery 30,000 km
(18,000 miles) or 24 months
± B ± ± ± ± ± ±ITEM 6-8
Suspension bolts and nutsTEvery 15,000 km
(9,000 miles) or 12 months
± B C D ± ± ± HITEM 6-7
Wheel bearingIEvery 15,000 km
(9,000 miles) or 12 months
CD
ITEM 6-17
Air conditioning filter*2
IEvery 15,000 km
(9,000 miles) or 12 months
± ± C D ± ± ± ±Air conditioning filter 2
(if equipped)REvery 45,000 km
(27,000 miles) or 36 months
NOTES:
ªIº : Inspect and correct, replace or lubricate if necessary
ªRº : Replace or change
ªTº : Tighten to the specified torque
*1 : Inspect or replace more frequently if necessary.
*2 : Clean or replace more frequently if the air from the air conditioning decreases.

YH4
GRAND
VITARA
1. Crankshaft pulley
2. Water pump pulley
3. 100 N, 10 kg or 22 lb
G16
H25
MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SERVICE
ENGINE
ITEM 1-1
Drive Belt Inspection and Replacement
WARNING:
All inspection and replacement are to be performed with
ENGINE NOT RUNNING.
Water pump and generator drive belt (G16 and H25 engines)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace.
Check belt for tension.
Water pump and generator belt tension
ªaº: 6 ± 8 mm (0.24 ± 0.32 in.) deflection for G16, 9 ± 11 mm
(0.35 ± 0.43 in.) deflection for H25 under 100 N, 10 kg or
22 lb pressure
NOTE:
When replacing belt with a new one, adjust belt tension to
5 ± 6 mm (0.20 ± 0.24 in.) for G16, 7 ± 9 mm (0.28 ± 0.35 in.)
for H25.
3) If belt is too tight or too loose, adjust it to specification by adjust-
ing alternator position.
4) Tighten alternator adjusting bolt and pivot bolts.
5) Connect negative cable to battery.
Replacement
Replace belt. Refer to Section 6B for replacement procedure of
pump belt.