Page 92 of 969
C91925
C86316
Magnet
AT0103
Magnet
C91927
Temperature
Sensor
D03547
Transmission Wire
40-20
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
44 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
9. REMOVE AUTOMATIC TRANSAXLE OIL PAN
SUB-ASSY
(a) Remove the 18 bolts, oil pan and gasket.
(b) Remove the 2 magnets from the oil pan.
10. INSPECT TRANSMISSION OIL CLEANER MAGNET
(a) Remove the magnets and use them to collect any steel
chips. Examine the chips and particles in the pan and on
the magnet to determine what type of wear has occurred
in the transaxle:
Steel (magnetic).... bearing, gear and plate wear
Brass (non-magnetic).... bushing wear
11. DISCONNECT TRANSMISSION WIRE
(a) Remove the 7 connectors from the shift solenoid valves.
(b) Remove the bolt, lock plate and ATF temperature sensor.
12. REMOVE TRANSMISSION WIRE
(a) Remove the bolt and transmission wire from the transaxle
case.
Page 96 of 969
D03560
C56727
D03563
D03564
D03565
40-24
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
48 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
23. REMOVE MANUAL DETENT SPRING SUB-ASSY
(a) Remove the 2 bolts, the manual detent spring sub-assy
and cover.
24. REMOVE PARKING LOCK PAWL BRACKET
(a) Remove the 2 bolts and parking lock pawl bracket.
25. REMOVE MANUAL VALVE LEVER SUB-ASSY
(a) Using a chisel and hammer, cut off and remove the
spacer.
(b) Using a pin punch (f35 mm) and hammer, drive out the
pin.
HINT:
Slowly drive out the pin so that it will not fall into the transaxle
case.
(c) Remove the manual valve lever shaft and manual valve
lever.
Page 97 of 969
D26382
Parking Lock Rod Sub-assy
D03566
D08046Oil Pump Assy
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-25
49 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
26. REMOVE PARKING LOCK ROD SUB-ASSY
(a) Remove the parking lock rod from the manual valve lever.
27. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
(a) Using a screwdriver, remove the oil seal from the trans-
axle case.
28. FIX AUTOMATIC TRANSAXLE ASSY
(a) Fix the transaxle case with the oil pump side facing up.
29. INSPECT INPUT SHAFT ENDPLAY
(a) Using a dial indicator, measure the input shaft endplay.
Endplay: 0.262 - 1.244 mm (0.01 - 0.049 in.)
Page 100 of 969
D03829
Dial Indicator
Forward Clutch Hub
D03576
Pawl Shaft Clamp
D09652
D09689
40-28
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
52 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
38. INSPECT MULTIPLE DISC CLUTCH CLUTCH HUB
(a) Using a dial indicator, measure the inside diameter of the
forward clutch hub bushing
Standard inside diameter:
23.025 - 23.046 mm (0.9065 - 0.9073 in.)
Maximum inside diameter: 23.09 mm (0.9091 in.)
NOTICE:
When the diameter is over the maximum, replace the
multiple disc clutch hub with new one.
Check the contact surface of the bush in the direct
clutch shaft. If any scratch or discolor is identified, re-
place the direct clutch sub-assy with new one.
If the inside diameter is greater than the maximum, replace the
forward clutch hub.
39. REMOVE UNDERDRIVE PLANETARY GEAR ASSY
(a) Remove the bolt and pawl shaft clamp.
(b) Remove the parking lock pawl shaft.
(c) Push the parking lock pawl.
HINT:
Failure to do so will cause interference when the underdrive
planetary gear is removed.
Page 101 of 969
D03579
Underdrive
Planetary
Gear Assy
D26386
D03580
Thrust Bearing
Bearing Race
D03581Snap Ring
D03627
Underdrive
1-W ay
Clutch
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-29
53 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(d) Remove the underdrive planetary gear assy from the
transaxle case.
NOTICE:
Be careful so that the underdrive planetary gear assy will
not fall out.
40. REMOVE PARKING LOCK PAWL
(a) Remove the spring, pawl pin and parking lock pawl.
41. REMOVE UNDERDRIVE CLUTCH ASSY
(a) Remove the underdrive clutch assy, thrust bearing and
bearing race from the transaxle case.
42. REMOVE UNDERDRIVE 1 WAY CLUTCH ASSY
(a) Using a screwdriver, remove the snap ring from the trans-
axle case.
(b) Remove the underdrive 1-way clutch from the transaxle
case.
Page 108 of 969
D03595
Lock Washer
D03596
SST
D26398
SST
D26763
Front Planetary
Gear Assy
Brake Hub
D03615
Front Planetary Ring Gear
Brake Hub
Snap Ring
40-36
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
60 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
65. REMOVE FRONT PLANETARY GEAR ASSY
(a) Using a chisel and hammer, unstake the lock washer.
NOTICE:
Push down all claws of the washer. Otherwise SST cannot
be fully pressed against the nut, and cannot loosen the nut.
(b) Using SST, remove the nut.
SST 09387-00030, 09387-00080
(c) Using SST and a press, remove the front planetary gear
assy from the counter drive gear.
SST 09950- 60010 (09951- 00450), 09950- 70010
(09951-07100)
(d) Remove the front planetary gear assy from the brake hub.
66. REMOVE FRONT PLANETARY RING GEAR
(a) Using a screwdriver, remove the snap ring and front plan-
etary ring gear from the brake hub.
Page 122 of 969
D03918
SST
D08074
Lock Washer
C89123
C
BA
Input Sun Gear
D
40-50
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
74 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(e) Using SST and a torque wrench, measure the turning
torque of the bearing while rotating SST at 60 rpm. When
the measured value is not within the specified value,
gradually tighten the nut until it reaches the specified val-
ue.
SST 09387-00080
Turning torque at 60 rpm:
New Bearing
0.51 - 1.02 NVm (5.1 - 10.0 kgfVcm, 4.4 - 8.7 in.Vlbf)
Used Bearing
0.26 - 0.51 NVm (2.7 - 5.2 kgfVcm, 2.3 - 4.5 in.Vlbf)
HINT:
Use a torque wrench with a fulcrum length of 160 mm (6.3 in.).
(f) Tighten the nut gradually until the specified rotation
torque of tapered roller bearing is measured.
Torque: 350 NVm (3,569 kgfVcm, 258 ftVlbf) (a limit)
(g) Using a chisel and hammer, stake the front lock washer.
98. INSTALL INPUT SUN GEAR
(a) Coat the 2 thrust bearings with ATF.
(b) Install the 2 thrust bearings, the bearing race and the front
planetary sun gear to the front planetary gear assy.
NOTICE:
Install the bearing race on the side of the front plane-
tary carrier. Be careful about the orientation of the
race.
Installing thrust bearing and front sun gears, be care-
ful about the orientation of the parts.
Install the bearing race on the side of the front sun
gear. Be careful about the orientation of the race.
Install the thrust bearing and the race after holding
the parts on the rear planetary carrier by applying
grease. Be sure the assembling order.
Page 125 of 969
D03909
1-W ay Clutch
Inner Race
D09638
Free
D03588
Thrust Needle
Roller Bearing
1-W ay Clutch Assy
D26394
Planetary Carrier
Thrust Washer No.1
D26393
Planetary Carrier Thrust Washer No.2
Rear Planetary Sun Gear
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-53
77 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
104. INSTALL 1 WAY CLUTCH ASSY
(a) Install the 1-way clutch inner race to the 1-way clutch.
NOTICE:
Check the direction of the inner race.
Confirm that the discrimination mark can be seen by
the worker.
(b) Check the rotating direction of 1-way clutch for the lock
or free operation, as shown in the illustration.
(c) Install the 1-way clutch and thrust needle roller bearing
to the 1-way clutch sleeve outer.
Bearing diameter: mm (in.)
InsideOutside
Bearing53.6 (2.110)69.4 (2.732)
NOTICE:
Install the thrust bearing properly so that no-colored race
will be visible.
105. INSTALL PLANETARY CARRIER THRUST WASHER
NO.1
(a) Coat the planetary carrier thrust washer No. 1 with yellow
petrolatum, install it onto the planetary sun gear assy.
NOTICE:
After assembling, confirm that the projection should be
fixed surely in the hole of the planetary sun gear assembly.
106. INSTALL REAR PLANETARY SUN GEAR ASSY
(a) Coat the planetary carrier thrust washer No. 2 with yellow
petrolatum, install it onto the rear planetary sun gear.
