2005 LEXUS ES300 lock

Lexus Supports ASE CertificationPage 1 of 2
Title:
MAIN BEARING JOURNAL DIAMETER
STAMPING LOCATION REVISION
Models:
'04 ± '05 ES 330 & RX 330
Technical Service
Information Bulletin
October 14, 2004
EG011-04
The main bearing journal diameter stamp location has been changed on some 2004 and
2005 model year vehicles with 3MZ±FE engines. The stamping on the front of the block
has been discontinued. Review this TSB for the stamping location.
2004 ± 2005 model year ES 330 and RX 330 vehicles meeting the
following specifications:
3MZ±FE equipped vehicles with engine serial numbers starting after 0138096.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
ENGINE
Introduction
Applicable
Vehicles
Warranty
Information

MAIN BEARING JOURNAL DIAMETER STAMPING LOCATION REVISION ± EG011-04October 14, 2004
Page 2 of 2
Underside of Cylinder Block
(Contact Surface with Oil Pan No. 1)Front of Cylinder Block Cylinder Block Main Journal Bearing Diameter Location
Current
LocationPrevious Location
(Discontinued)
Front
HINT:
If replacing a bearing, replace it with one that has the same number. If the number of the
bearing cannot be determined, select the correct bearing by adding together the
numbers imprinted on the cylinder block and crankshaft, then refer to the table on the
bottom of this page for the appropriate bearing number. The No. 1 and No. 4 journal
bearings have 5 standard bearing sizes, marked 3, 4, 5, 6, and 7 accordingly.
The No. 2 and No. 3 journal bearings have 5 standard bearing sizes, marked 1, 2, 3, 4,
and 5 accordingly.
No. 1No. 2No. 3No. 4
Number
Mark
No. 1No. 2No. 3
No. 4
Number
Mark
Number
Mark
Cylinder Block + Crankshaft =0 to 56 to 1112 to 1718 to 2324 to 28
Replacement Bearing34567
EXAMPLE:
Cylinder block imprinted number mark is ª06.º
Crankshaft imprinted number mark is ª08.º
6 + 8 = 14
Select the bearing marked ª5.º Main Bearing
Location

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 2 of 9
D.C.C. FUSE INSTALLATION DURING PDS
The D.C.C. fuse has been removed at the assembly plant to reduce parasitic current
draw in transit and storage.
The removed D.C.C. fuse (30 A) is stored in the blank space of the Junction Block in
the engine compartment. The D.C.C. fuse must be reinstalled during Pre±Delivery
Service (PDS) in the dealership as shown below.
Junction Block
Install D.C.C. Fuse (30 A)
Here (Original Location)Remove This Fuse
NOTE:
Removing the D.C.C. fuse cuts off power sources relating to the Dome, ECU±B and
RAD No. 1 fuses.
If the vehicle is stored in the dealership for a long period of time after PDS,
disconnect the negative battery terminal to prevent battery discharge. Refer to TSIB
PG009±02 for battery maintenance information.
ITEM NO. 1:
Introduction
Installation
Procedure

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 3 of 9
REMOVAL OF FRONT EMERGENCY TOWING EYELET AND INSTALLATION OF
TOWING EYELET HOLE COVER (PERFORMED AT PORT)
1. Remove the emergency towing eyelet
from the front bumper by turning
counterclockwise.
NOTE:
If it is hard to loosen the emergency
towing eyelet, use a steel bar.
2. Place the removed emergency
towing eyelet in the tool tray in the
luggage compartment.
3. Install the front towing eyelet hole
cover which is stored in the glove box
onto the front bumper as shown in
the diagram. ITEM NO. 2:
Emergency Towing Eyelet
Installation
Procedure

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 8 of 9
INITIAL CALIBRATION OF COMPASS (Continued)
3. Check that the direction appears
several seconds after adjustment.
4. Start the engine and push the switch
for about 6 seconds until ªCº appears
on the display.
5. Drive the vehicle slowly at 5 mph, or
less, in a circle until the direction is
displayed. If there is not enough space
to drive in a circle, drive around the
block until the direction is displayed.
After driving in circles 1 to 3 times,
calibration is complete with the direction
shown on the display.
NOTE:
Do not perform calibration of the compass in a place where the earth's magnetic
field is subject to interference by artificial magnetic fields (underground parking,
under a steel tower, between buildings, roof parking, near a railroad crossing, near
a large vehicle, etc.)
During calibration, do not operate electric systems (moon roof, power windows,
etc.) as they may interfere with the calibration.
ITEM NO. 5:
Compass
Calibration
Procedure
(Continued)

Lexus Supports ASE CertificationPage 1 of 1
Title:
DCC FUSE INSTALLATION DURING PDS
Models:
'05 ± '06 ES 330
Technical Service
Information Bulletin
August 22, 2005
PD032-05
The DCC fuse has been removed at the assembly plant to reduce parasitic current
draw in transit and storage.
2005 ± 2006 model year ES 330 vehicles.
The removed DCC fuse (30A) is stored in the blank space of the Junction Block in
the engine compartment. The DCC fuse must be reinstalled during Pre-Delivery Service
(PDS) in the dealership as shown below.
Junction Block
Install DCC Fuse (30A)
Here (Original Location)Remove This Fuse
NOTE:
Removing the DCC fuse cuts off power sources relating to the DOME, ECU±B, and
RAD No. 1 fuses.
If the vehicle is stored in the dealership for a long period of time after PDS,
disconnect the negative (±) battery terminal to prevent battery discharge. Refer to
TSIB No. PG009±02, ª
Battery Maintenance for In-Stock Vehicles & Pre-Delivery,º for
battery maintenance information.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
PRE-DELIVERY SERVICE
Introduction
Applicable
Vehicles
Installation
Procedure
Warranty
Information

INITIAL CALIBRATION OF COMPASS DURING PDS ± PD034-05 August 22, 2005
Page 3 of 3
3. Check that the direction appears
several seconds after adjustment.
4. Start the engine and push the switch
for about 6 seconds until ªCº appears
on the display.
5. Drive the vehicle slowly at 5 mph
(8 km/h), or less, in a circle until the
direction is displayed. If there is not
enough space to drive in a circle,
drive around the block until the
direction is displayed.
After driving in 1 to 3 circles,
calibration is complete with the
direction shown on the display.
NOTE:
Do NOT perform calibration of the compass in a place where the Earth's magnetic
field is subject to interference by artificial magnetic fields (underground parking,
under a steel tower, between buildings, roof parking, near a railroad crossing, near
a large vehicle, etc.)
During calibration, do NOT operate electric systems (moon roof, power windows,
etc.) as they may interfere with the calibration. Compass
Calibration
Procedure
(Continued)

Lexus Supports ASE CertificationPage 1 of 2
Title:
FRONT EMERGENCY TOWING EYELET &
EYELET HOLE COVER
Models:
'05 ± '06 ES 330
Technical Service
Information Bulletin
August 26, 2005
PD037-05
The 2005 ± 2006 model year ES 330 is shipped with a front emergency towing eyelet.
Follow the procedure below to remove the eyelet and save for customer use.
2005 ± 2006 model year ES 330 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
1. Remove the emergency towing
eyelet from the front bumper by
turning counterclockwise.
NOTE:
If it is hard to loosen the emergency
towing eyelet, use a steel bar.
PRE-DELIVERY SERVICE
Introduction
Applicable
Vehicles
Warranty
Information
Emergency Towing Eyelet
Installation
Procedure