2005 LEXUS ES300 lock

SENSOR INSPECTION FOR AIR CONDITIONING SYSTEM ± AC005-04 December 16, 2004
Page 9 of 12
Procedure B:
a. Disconnect the solar
sensor connector.
b. Measure the resistance between
terminals 2 and 3 of the solar
sensor under the
following conditions:
Cover the sensor with a cloth
to avoid direct light.
Expose the sensor to light
from a distance of 300 mm
(11.81 in.) or less with an
inspection light.
NOTE:
When using an analog tester, connect
the positive (+) lead to terminal 3 and
negative (±) lead to terminal 2 of the
solar sensor.
HINT:
If the light is weak, the sensor may not react. Be sure to use an incandescent light for
an inspection light.
Standard:
CONDITIONSPECIFICATION
When the sensor is covered with a cloth
(to avoid direct light)Infinite ohms
When the sensor is exposed to lightLess than infinite resistance
Inspection
Procedure
(Continued)
Lock

Page 5 of 6
Failure to follow the recommendations indicated below could result in reduced
effectiveness of the seat belt restraint system in case of vehicle collision, causing
personal injury.
If your seat belt cannot be fastened securely because it is not long enough, a
personalized Seat Belt Extender is available from your Lexus dealer free of charge.
Please visit your local Lexus dealer so that the dealer can order the proper required
length extender. Bring the heaviest coat you expect to wear for proper measurement and
selection of length. Additional ordering information is available at your Lexus dealer.
When the Seat Belt Extender is provided for rear seat positions (with automatic locking
retractor), make sure that the retractor is locked when in use.
To connect the extender to the seat
belt, insert the tab into the seat belt
buckle so that the buckle-release
buttons of the extender and the seat
belt are both facing outward as shown.
You will hear a click when the tab locks
into the buckle.
When not in use, remove the extender
and store in the vehicle for future use.
CAUTION:
On vehicles equipped with SRS ± Occupant Classification System (OCS)*, it is
critical that the extender tab be buckled into the buckle AFTER the occupant sits
down in the seat.
Leaving extender installed in the buckle before sitting down will cause the OCS to be
in the ªairbag offº or disarmed state.
* OCS will enable or disable the passenger front and side airbags based on passenger weight and seat belt
latch position classifying the passenger as a child or adult.
CAUTION:
When using the Seat Belt Extender, observe the following. Failure to follow these
instructions could result in reduced effectiveness of the seat belt restraint system in
case of vehicle accident, increasing the chance of personal injury.
Never use the Seat Belt Extender if you can COMFORTABLY fasten the seat belt
without it.
The Seat Belt Extender must never be used with any child safety seats.
Remember that the extender provided for you may not be safe when used on a
different vehicle, for another person or for a different seating position than the one
originally intended.September 29, 2004
SEAT BELT EXTENDER: '03±'05 MODEL YEAR ± BO009-04 Revised
Owner
Instructions
Seat Belt ExtenderSeat Belt Release

Page 6 of 6
SEAT BELT EXTENDER WORKSHEET
PLEASE COPY THIS ORIGINAL WORKSHEET FOR EACH EXTENDER NEEDED
CAUTIONS:
To minimize the chance and/or severity of injury in an accident, the Seat Belt Extender must only be used:
1 By the person for whom it was provided.
2 In the seat position for which it was provided.
The Seat Belt Extender must never be used with any child safety seats.
When the Seat Belt Extender is provided for rear seat positions (with automatic locking retractor),
make sure the retractor is locked when extender belt is in use.
DEALER
SEAT BELT EXTENDER APPLICATIONAPPLICANT
DEALER
CODEDEALER
NAMEAPPLICANT
NAME
ADDRESSADDRESS
CITY
&
STATEZIPCITY
&
STATEZIPPHONE
EMPLOYEE
NAMEMODEL
YEARBODY
TYPESEATING
POSITIONVEHICLE
IDENTIFICATION
NUMBER
DIRECTIONS FOR DETERMINING PROPER EXTENDER LENGTH
1. Place the seat in the position the applicant normally uses.
2. With the applicant in the seat, wearing the thickest coat expected to be worn, pull belt all the way out and try to
buckle belt.
If belt latches into buckle and feels comfortable against upper chest area, an extender is not needed.
If belt does not buckle, continue with Step 3.
If buckle latches but belt has no slack remaining, continue with Step 3.
3. Measure distance between applicant's navel and seat belt buckle (Dimension A) and enter on Worksheet.
4. With belt all the way out, measure distance between latch tip and buckle tip (Dimension B) and enter
on Worksheet.
NOTE: If belt latches but there is no slack enter zero as Dimension B.
5. Subtract Dimension B from Dimension A and record number in Check Number box on Worksheet.
6. Seat Belt Extender length is Dimension B rounded up to next extender length (without exceeding
Check Number).
NOTE: If extender length exceeds Check Number, an extender cannot
be provided to the customer.
CAUTION:
On vehicles equipped with SRS Ð Occupant Classification System (OCS), it is critical that the extender
tab be buckled into the buckle AFTER the occupant sits down in the seat.
Leaving extender installed in the buckle before sitting down will cause the OCS to be in the ªairbag offº
or disarmed state.
Dimension A:
NAVEL TO BUCKLEDimension B:
LATCH TO BUCKLE
BuckleNavel
ABuckle
Latch
B
SEAT BELT EXTENDER CALCULATION
DIMENSION
A:DIMENSION
B:CHECK
NUMBER:
SEAT BELT EXTENDER AUTHORIZATION
The same Seat Belt Extender can be used for right and left seating applications. Each Seat Belt
Extender will have a label identifying the owner, VIN and seating position.
Applicant's Signature:
Date:
(Actual user of Seat Belt Extender)

REAR BUCKLE EASE OF USE IMPROVEMENT ± BO011-05 Revised November 9, 2005
Page 5 of 9
12. Install the rear seat center belt assembly RH.
A. Check the degree of tilt when the ELR begins to lock.
Check that the belt does NOT lock at less then 15
of tilt in any direction
but locks at over 45
of tilt when gently moving the installed retractor.
Unlock
Lock455
B. Install the retractor of the rear seat center belt assembly RH and torque the bolt.
Torque: 42 Nm (420 kgfcm, 31 ftlbf)
C. Check the ELR lock.
Check that the belt locks when pulled out quickly.
D. Check the fastening function for the child restraint system.
NOTE:
Check should be done with the assembly installed.
a. Check that the belt cannot be pulled out any more but can be rewound after
being pulled out.
b. Check that the belt can be pulled out and rewound after being fully rewound.
Repair
Procedure
(Continued)

REAR BUCKLE EASE OF USE IMPROVEMENT ± BO011-05 Revised November 9, 2005
Page 6 of 9
E. Install the floor anchor of the rear seat center belt assembly RH with the bolt
facing the arrow mark on the plate toward the front of the vehicle.
Torque: 42 Nm (420 kgfcm, 31 ftlbf)
NOTE:
Ensure that the anchor does NOT run into any protrusions on the floor panel.
FrontProtrusion
Protrusion
F. Check the ELR lock.
Check that the belt locks when pulled out quickly.
13. Remove the rear seat center belt assembly LH.
Remove the bolt and remove the rear seat center belt assembly LH.
Repair
Procedure
(Continued)

REAR BUCKLE EASE OF USE IMPROVEMENT ± BO011-05 Revised November 9, 2005
Page 7 of 9
14. Install the rear seat center belt assembly LH.
A. Check the degree of tilt when the ELR begins to lock.
Check that the belt does NOT lock at less then 15
of tilt in any direction
but locks at over 45
of tilt when gently moving the installed retractor.
Unlock
Lock455
B. Install the retractor of the rear seat center belt assembly LH and torque the bolt.
Torque: 42 Nm (420 kgfcm, 31 ftlbf)
C. Check the ELR lock.
Check that the belt locks when pulled out quickly.
D. Check the fastening function for the child restraint system.
NOTE:
Check should be done with the assembly installed.
a. Check that the belt cannot be pulled out any more but can be rewound after
being pulled out.
b. Check that the belt can be pulled out and rewound after being fully rewound.
Repair
Procedure
(Continued)

REAR BUCKLE EASE OF USE IMPROVEMENT ± BO011-05 Revised November 9, 2005
Page 8 of 9
E. Install the floor anchor of the rear seat center belt assembly LH with the bolt
facing the arrow mark on the plate toward the front of the vehicle.
Torque: 42 Nm (420 kgfcm, 31 ftlbf)
NOTE:
Ensure that the anchor does NOT run into any protrusions on the floor panel.
FrontProtrusion
Protrusion
F. Check the ELR lock.
Check that the belt locks when pulled out quickly.
15. Install the package tray trim panel assembly.
A.Without Sun Shade:
Engage the 6 claws and 2 clips to install the package tray trim panel assembly.
: Claw
: Clip
Repair
Procedure
(Continued)

Lexus Supports ASE CertificationPage 1 of 1
Title:
CENTER CONSOLE
LATCH IMPROVEMENT
Models:
'02 ± '05 ES 300 & ES 330
Technical Service
Information Bulletin
December 22, 2004
BO012-04
For improved durability, the center console door lock opener for ES 300 and ES 330
vehicles are now made from metal, instead of the previous plastic material. This improved
lock is available as a service part and will not require replacement of the entire
console lid.
2002 ± 2005 model year ES 300 and ES 330 vehicles produced BEFORE the
Production Change Effective VINs shown below.
PLANTPRODUCTION CHANGE EFFECTIVE VIN
TsutsumiJTHBA30G#50024455
KantoJTHBA30G#55077938
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAMEQTY
58908±3205058908±32020Lock Assembly, Console
Compartment Door1
OP CODEDESCRIPTIONTIMEOFPT1T2
BD4024Replace Center Console Lock0.258908±320506212
Applicable Warranty*:
This repair is covered under the Lexus Comprehensive Warranty. This warranty is in
effect for 48 months or 50,000 miles, whichever occurs first, from the vehicle's
in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Warranty
Information