2005 JAGUAR S TYPE Technical Guide Update

JAGUARS-TYPEBody
20system mirrors. A clear patch in the darkened
area at the bottom left of the windshield gives
external visible access to the VIN.
There are three types of windshield variants:
¥ Rain sensing, with electrochromic mirror
(NAS markets have the option of a compass
fitted to the mirror head).
¥ Non-rain sensing with electrochromic mirror
(NAS markets have the option of a compass
fitted to the mirror head).
¥ Non-rain sensing with prismatic mirror.
Windshields are available as heated or non-
heated and the rain sensing versions have a
unique mirror mounting system.
Backlight
The backlight is direct glazed to body. All
backlights are heated and have solar control tint,
integral radio and telephone antenna. The
backlight heater is timed on for 10 minutes.
Door glass
Each front door window is single curvature glass,
5mm thick, and operated by a twin guide cable
and drum assembly with five stud fixing points.
The glass is clamped to the regulator slide blocks.
Access holes are provided in the inner door when
the glass is raised. There are no adjustable end of
travel stops.
Rear door glass is also a single curvature glass,
4mm thick, with a single guide cable and drum
assembly and three stud fixing points. The glass
drops fully to the door roll. The glass is located to
the slider blocks by pins and has no adjustable
end of travel stops.
Each front and rear cable and drum mechanisms
must be replaced as individual complete units,
they have no serviceable parts.
Quarter lights
Quarter lights are 4mm thick with three fixings,
one is a lower bracket to the door inner.
Perimeter foam and butyl rubber seals are fitted
to the door outer.

JAGUARS-TYPEBody
21 Door exterior handles are body coloured and
have semi flush door handles. The driverÕs door
only has a door key lock barrel, barrel shield,
door latch shield and lock barrel operating
linkage. To replace/service the door key lock
barrel requires removal of the exterior handle.
Door mirrors have body coloured caps and
common 70 degree head angle, with three point
fixings to the door outer panel. Various
alternatives include power fold-back,
electrochromic, aspheric, memory and heated.
Side impact beams are mounted in the doors.
Doors and Door Mirrors
EXTERIOR DRIVERÕS DOOR HANDLE
JOL.138
J.501.1789
FRONT AND REAR DOORS
Driver Door Control
Module Bracket

JAGUARS-TYPEBody
22
JOL.070
INTERIOR DOOR HANDLE
Lock Lever
The only door module, the driver door control
module (DDCM) is mounted in the driverÕs side
door adjacent to the door speaker unit.
The interior door handle has a release cable to the
door latch.
J.418.429
DRIVER DOOR CONTROL MODULE

JAGUARS-TYPEBody
23
Windshield Wipers and Washers
The windshield wiper linkages and motor are a
combined unit with the operating logic integrated
into the GECM. The wiper system has two wiper
arms/blades which are handed for LHD or RHD.
Wipers are twin speed with variable six speed
intermittent operation and, optionally, moisture
sensitive operation.
Wiper arms do not lock away from the glass, they
must be held away from the windshield when
cleaning the glass. A special tool (501065) is
required to remove the wiper arms from the body.
Windshield washer jets are hood mounted. Two
sizes of washer reservoir are available, one for
windshield wash only, 4.4 litres, and one for
windshield wash and headlamp power wash,
6.6 litres. The reservoir is mounted forward of the
RH front wheel.
Headlamp power wash jets extend by water
pressure and retract by spring pressure.
A spoiler is fitted to the driverÕs wiper blade for
UK and European markets only.
D.501.1778
WINDSHIELD WIPER ASSEMBLY

JAGUARS-TYPEBody
24
Exterior and Interior Trim
J.501.1784
INTERIOR CARPET
J.501.1784
No coach line will be applied. The optional
equipment headlamp power washers are body
coloured as are the door handles and body side
protective mouldings. The vehicle has a chromed
radiator grille surround with gunmetal vertical
grille vanes.
Front license plate plinth when required is
mounted to the front bumper and the rear license
plate is mounted directly to the trunk drop panel
The A, B/C upper and D/E post trim are structural
parts designed to absorb energy during occupant
head impact. These parts must be replaced
following accident damage if impacted. Damage
may not be evident unless the parts are removed
and examined for damage such as cracking, stress
whitening or rib crushing. The headlining also
contains energy absorbing elements which need to
be replaced in the event of accident damage. The
headlining must be removed to inspect the foam
parts and if any have come loose or been
damaged through cracking or crushing then the
complete headlining must be replaced.
Mirrors
The standard fit manual dip mirror has a double
ball joint for adjustment. Electrochromic and rain
sensing versions may be fitted. North American
vehicles can also have an optional compass fittedwithin the mirror head. The mirror mounting is
supplied bonded to the windshield.
Carpets
The interior carpet is a complete, one-piece design
Trunk carpeting comprises
¥ A folding floor panel.
¥ Two styles of trunk LH carpet, one for
Navigation CD with 4 fixings and one without
CD with 3 fixings. When the Navigation CD
player is fitted it has a separate carpet trim
cover.
¥ A RH side trim carpet with 3 fixings.
¥ A single piece trunk lid liner with 11 fixings.
When a space saver wheel is stowed in the trunk,
an under floor stowage tray is provided under the
folding floor carpet.

JAGUARS-TYPEBody
25
Fascia
The fascia has 5 mounting points, left and right
side of the tunnel, left and right side of the fascia
and a point above the steering column. A steel
structure supports the fascia pad and the upper
steering column. The glovebox is used as the
mounting for the CD autochanger when this
option is fitted and also storage for the owners
literature pack. For base models a cassette storage
tray is fitted to the centre of the fascia but this is
deleted when the optional phone presenter or
navigation system is fitted. Unlike current models,
the ignition switch is set in the fascia, not on the
steering column.
J.501.1790
FASCIA

JAGUARS-TYPEBody
26
Seats
All seats are completely new to Jaguar with no
commonality to previous models.
Front Seats
The drivers seat and front passenger seat are
electrically adjustable for front and rear seat
height, fore and aft movement and squab tilt with
optional lumbar adjustment. Optional heated
cushions and squabs may be fitted with the heater
switches located on the centre console. The head
restraints are manually adjustable for height (four
positions) and tilt. The drivers seat also has an
optional two position memory facility. Side airbags
are fitted to both front seat squabs (see Occupant
Protection section).
Seat Construction
The seat track assembly consists of two slider
rails, cross mounted drive mechanisms and anelectrical harness sub-assembly. The seat cushion
pan is supported on four brackets attached to the
height adjustment drive actuators. Two separate
drive motors and screw actuator mechanisms
provide raise/lower movements respectively for
the front and rear of the cushion. The seat fore
and aft motor and drive shaft are located across
the front of the track assembly: note the drive
shaft must not be used to lift the seat assembly
when fitting or removing a seat. Each drive has a
potentiometer to register the selected position for
memory storage.
The track assembly wiring harness and driver seat
control module (DSCM) (driverÕs side only) are
fixed to a plastic tray which clips onto the frame.
The squab frame is a welded steel construction
which bolts to the track assembly and carries the
recline drive, lumbar support mechanism and a
D.501.1782
SEAT DRIVES
Fore/Aft Drive
Motor
Cushion Pan
Support Bracket
Driver or
Passenger Seat
Heater Module
Front Height
Drive Motor
Rear Height
Drive Motor
Potentiometer
(when fitted)

JAGUARS-TYPEBody
27
FRONT SEAT FRAME
Driver Seat Control Module
Lumbar Support
Recline Motor
Harness Sub-assembly
Lumbar Support
Motor