2005 INFINITI FX35 turn signal

TROUBLE DIAGNOSIS ATC-87
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
5. CHECK BCM INPUT (COMPRESSOR ON) SIGNAL
Check compressor ON/OFF signal. Refer to AT C - 4 0 , "
CONSULT-II
Function (BCM)" .
OK or NG
OK >> GO TO 8.
NG >> GO TO 6.
6. CHECK CIRCUIT CONTINUITY BETWEEN BCM AND UNIFIED METER AND A/C AMP.
1. Turn ignition switch OFF.
2. Disconnect BCM connector and unified meter and A/C amp. connector.
3. Check continuity between BCM harness connector M3 terminal 27 (R/Y) and unified meter and A/C amp. harness connector
M57 terminal 42 (R/Y).
OK or NG
OK >> GO TO 7.
NG >> Repair harness or connector.
7. CHECK VOLTAGE FOR UNIFIED METER AND A/C AMP. (COMPRESSOR ON SIGNAL)
1. Reconnect BCM connector and unified meter and A/C amp. connector.
2. Turn ignition switch ON.
3. Check voltage between unified meter and A/C amp. harness connector M57 terminal 42 (R/Y) and ground.
OK or NG
OK >> GO TO 8.
NG-1 >> If the voltage is approx. 5 V when A/C switch is ON: Replace unified meter and A/C amp.
NG-2 >> If the voltage is approx. 0 V when A/C switch is OFF: Replace BCM. A/C SW ON : AIR COND SW ON
A/C SW OFF : AIR COND SW OFF
R J I A 1111 E
27 – 42 : Continuity should exist.
RJIA2006E
Te r m i n a l s
Condition Voltage
(+)
( − )
Unified meter
and A/C amp.
connector Terminal
No.
(wire color)
M57 42 (R/Y) Ground A/C switch: ON
(Blower motor operates.) Approx. 0 V
OFF switch: ON
(A/C system: OFF) Approx. 5 V
RJIA2007E

ATC-88
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
8. CHECK REFRIGERANT PRESSURE SENSOR
WITH CONSULT-II
1. Start the engine.
2. Check voltage of refrigerant pressure sensor. Refer to EC-147, "
CONSULT-II Reference Value in Data
Monitor" (VQ35DE) or EC-838, "CONSULT-II Reference Value in Data Monitor" (VK45DE).
WITHOUT CONSULT-II
1. Start the engine.
2. Check voltage between ECM harness connector F101 terminal 70 (L/R) and ground.
OK or NG
OK >>
WITH CONSULT-II
GO TO 9.

WITHOUT CONSULT-II
GO TO 10.
NG >> Refer to EC-674, "
REFRIGERANT PRESSURE SENSOR" (VQ35DE) or EC-1364, "REFRIGER-
ANT PRESSURE SENSOR" (VK45DE).
9. CHECK BCM INPUT (FAN ON) SIGNAL
Check FAN ON/OFF signal. Refer to AT C - 4 0 , "
CONSULT-II Function
(BCM)" .
OK or NG
OK >> GO TO 12.
NG >> GO TO 10.
10. CHECK CIRCUIT CONTINUITY BETWEEN BCM AND UNIFIED METER AND A/C AMP.
1. Turn ignition switch OFF.
2. Disconnect BCM connector and unified meter and A/C amp. connector.
3. Check continuity between BCM harness connector M3 terminal 28 (BR/Y) and unified meter and A/C amp. harness connector
M57 terminal 57 (BR/Y).
OK or NG
OK >> GO TO 11.
NG >> Repair harness or connector.
Te r m i n a l s
Condition Voltage
(+)
( − )
ECM
connector Terminal No.
(wire color)
F101 70 (L/R) Ground A/C switch: ON
(Blower motor operates.) Approx. 1 - 4 V
PBIB1188E
FAN SW ON : FAN ON SIG ON
FAN SW OFF : FAN ON SIG OFF
R J I A 1111 E
28 – 57 : Continuity should exist.
RJIA2009E

TROUBLE DIAGNOSIS ATC-89
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
11 . CHECK VOLTAGE FOR UNIFIED METER AND A/C AMP. (FAN ON SIGNAL)
1. Reconnect BCM connector and unified meter and A/C amp. connector.
2. Turn ignition switch ON.
3. Check voltage between unified meter and A/C amp. harness connector M57 terminal 57 (BR/Y) and ground.
OK or NG
OK >> GO TO 12.
NG-1 >> If the voltage is approx. 5 V when blower motor is ON: Replace unified meter and A/C amp.
NG-2 >> If the voltage is approx. 0 V when blower motor is OFF: Replace BCM. Refer to BCS-16,
"Removal and Installation of BCM" .
12. CHECK CAN COMMUNICATION
Check CAN communication. Refer to BCS-15, "
CAN Communication Inspection Using CONSULT-II (Self-
Diagnosis)" .

BCM – ECM

ECM – IPDM E/R

ECM – Unified meter and A/C amp.
OK or NG
OK >> INSPECTION END
NG >> Repair or replace malfunctioning part(s).
Te r m i n a l s
Condition Voltage
(+)
(-)
Unified meter
and A/C amp. connector Terminal No.
(wire color)
M57 57 (BR/Y) Ground A/C switch: ON
(Blower motor operates.) Approx. 0 V
OFF switch: ON
(A/C system: OFF) Approx. 5 V
RJIA2010E

TROUBLE DIAGNOSIS ATC-99
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
2. CHECK ECV CONTROL SIGNAL
1. Turn ignition switch OFF.
2. Reconnect compressor (ECV) connector.
3. Perform self-diagnosis. Refer to AT C - 5 3 , "
Self-diagnosis Func-
tion" .
4. Set in self-diagnosis STEP-4 (Code No. 45). Refer to AT C - 5 4 ,
"FUNCTION CONFIRMATION PROCEDURE" .
5. Confirm ECV control signal between unified meter and A/C amp. harness connector M57 terminal 45 (PU/W) and ground using
an oscilloscope.
OK or NG
OK >> Replace compressor.
NG >> GO TO 3.
3. CHECK CIRCUIT CONTINUITY BETWEEN ECV AND UNIFIED METER AND A/C AMP.
1. Turn ignition switch OFF.
2. Disconnect compressor (ECV) and unified meter and A/C amp. connector.
3. Check continuity between compressor (ECV) harness connector F6 terminal 3 (PU) and unified meter and A/C amp. harness
connector M57 terminal 45 (PU/W).
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK ECV
Check continuity between compressor (ECV) connector F6 terminals
2 and 3.
OK or NG
OK >> Replace unified meter and A/C amp.
NG >> Replace compressor.
RJIA2295E
RJIA1475E
3 – 45 : Continuity should exist.
RJIA2296E
2 – 3 : Continuity should exist.
RJIA2297E

AV-3
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
HISTORY OF ERRORS ...................................
. 136
DIAGNOSIS BY HISTORY OF ERRORS ........ . 137
NAVIGATION ................................................... . 138
CAN Diag Support Monitor .................................. . 140
OPERATION PROCEDURE ............................ . 140
A/C and AV Switch Self-Diagnosis Function ....... . 141
DESCRIPTION ................................................. . 141
Power Supply and Ground Circuit Check for NAVI
Control Unit ......................................................... . 142
Power Supply and Ground Circuit Check for Display
Control Unit ......................................................... . 143
Power Supply and Ground Circuit Check for Display . 144
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................ . 145
Vehicle Speed Signal Check for NAVI Control Unit . 145
Vehicle Speed Signal Check for Display Control Unit . 146
Illumination Signal Check for NAVI Control Unit .. . 147
Illumination Signal Check for Display Control Unit . 148
Ignition Signal Check for NAVI Control Unit ........ . 148
Ignition Signal Check for Display Control Unit .... . 148
Reverse Signal Check for NAVI Control Unit ...... . 148
Reverse Signal Check for Display Control Unit ... . 149
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) .................... . 149
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) ........................ . 150
Display Communication Line Check (Between Dis-
play Control Unit and Display) ............................. . 152
AV Communication Line Check (Between Display
Control Unit and A/C and AV Switch) .................. . 154
CAN Communication Line Check ........................ . 155
If NAVI Control Unit Detects That DVD-ROM Map
Is Not Inserted ..................................................... . 155
If NAVI Control Unit Detects That Inserted DVD-
ROM Map Malfunctioning Or If It Is Impossible to
Load Data from DVD-ROM Map ......................... . 155
If Connection Between NAVI Control Unit and GPS
AntennaIs Malfunctioning .................................... . 156
RGB Screen Is Not Shown .................................. . 156
Color of RGB Image Is Not Proper (NAVI Screen
Looks Bluish) ....................................................... . 157
Color of RGB Image Is Not Proper (NAVI Screen
Looks Reddish) ................................................... . 158
Color of RGB Image Is Not Proper (NAVI Screen
Looks Yellowish) .................................................. . 159
Color of RGB Image Is Not Proper (All Screens
Looks Bluish) ....................................................... . 160
Color of RGB ImageIs Not Proper (All Screens
Looks Reddish) ................................................... . 161
Color of RGB Image Is Not Proper (All Screens
Looks Yellowish) .................................................. . 162
RGB Screen Is Rolling (NAVI Screen) ................ . 163
RGB Screen Is Rolling (Excepting NAVI Screen) . 164
Guide Sound Is Not Heard .................................. . 165
Screen Is Not Shown .......................................... . 166
Audio Screen Is Not Shown (NAVI Screen Is Shown) . 166
A/C Screen Is Not Shown (NAVI Screen Is Shown) . 166
TRIP, FUEL ECON and MAINTENANCE Screens
Are Not Shown .................................................... . 166 Average Fuel Economy Displayed Is Not Shown . 167
Driving Distance or Average Speed Displayed Is Not
Shown .................................................................. .167
WARNING DOOR OPEN Screen Is Not Shown .. .168
Tire Pressure Is Not Displayed ............................ .168
Unable to Operate All of A/C and AV Switch (Unable
to Start Self-Diagnosis) ........................................ .168
Navigation System Does Not Activate ................. .169
Position of Current-Location Mark Is Not Correct . 169
Driving Test .......................................................... .170
Example of Symptoms Judged Not Malfunction .. .171
BASIC OPERATION ......................................... .171
VEHICLE MARK ............................................... .171
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ............. .172
VOICE GUIDE .................................................. .172
ROUTE SEARCH ............................................. .172
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ............................................. .174
CURRENT LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ....... .177
CURRENT-LOCATION MARK JUMPS ............ .177
CURRENT LOCATION MARK IS IN A RIVER OR
SEA .................................................................. .178
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE .............................................................. .178
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ................................................... .178
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ............................... .178
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED ............................................................ .178
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ....... .178
Program Loading of NAVI Control Unit ................ .179
Removal and Installation of NAVI Control Unit .... .180
REMOVAL ........................................................ .180
INSTALLATION ................................................ .180
Removal and Installation of GPS Antenna .......... .180
REMOVAL ........................................................ .180
INSTALLATION ................................................ .180
Removal and Installation of A/C and AV Switch .. .181
Removal and Installation of Display Unit ............. .181
Removal and Installation of Display Control Unit . 181 REMOVAL ........................................................ .181
INSTALLATION ................................................ .181
INFINITI MOBILE ENTERTAINMENT SYSTEM .... .182
System Description .............................................. .182
Component Parts and Harness Connector Location .183
Wiring Diagram – MES – ..................................... .184
Terminals and Reference Value for DVD Player .. .186
Terminals and Reference Value for DVD Display . 187
DVD Player Does Not Work ................................ .189
Screen Is Not Shown (While Sounds Come Out of
an Audio Speaker, Did Not Do of a Head Phone) .191
Screen Is not Shown (Sounds Come Out of Both

AV-36
AUDIO
Revision: 2005 July 2005 FX
Terminals and Reference Value for A/C and AV SwitchAKS00A2B
Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltage Example of
symptom
+– Ignition
switch Operation
1 (W/L) Ground Battery power
supply Input OFF — Battery voltage System does not
work properly.
2 (LG/R) Ground ACC power
supply Input ACC — Battery voltage System does not
work properly.
3 (R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (position 1). Approx. 12 V
A/C and AV
switch illumina-
tion does not
come on when
lighting switch is
ON (position 1).
Turn lighting switch
OFF. Approx. 0 V
4 (R/Y) Ground Illumination
control signal Output ON Illumination control
switch is operated
by lighting switch in 1st or 2nd position. Changes between approx.0 V
and approx.12 V Audio unit illumi-
nation can not be
controlled.
5 (B) Ground Ground — ON — Approx. 0 V —
6 (B/R) Ground Communica-
tion signal (+) Input/
Output ON — System does not
work properly.
7 — Shield — — — — —
8 (W/R) Ground Communica-
tion signal (–) Input/
Output ON —
System does not
work properly.
12 (R/G) Ground Steering SW
A Input ON Press MODE switch. Approx. 0 V
Steering wheel
audio controls do
not function
Press SEEK UP
switch. Approx. 1.7 V
Press VOL UP
switch. Approx. 3.3 V
Except for above Approx. 5 V
13 (G/W) Ground Steering SW
B Input ON Press POWER
switch. Approx. 0 V
Steering wheel
audio controls do
not function
Press SEEK DOWN
switch. Approx. 1.7 V
Press VOL DOWN
switch. Approx. 3.3 V
Except for above Approx. 5 V
14 (B/Y) — Steering SW
ground —— — — Steering wheel
audio controls do
not function.
SKIA0175E
SKIA0176E

AUDIO AV-37
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Terminals and Reference Value for WooferAKS00AM2
A/C and AV Switch Self-Diagnosis FunctionAKS007OE
It can check ON/OFF operation of each switch in the A/C and AV switch and diagnose the input signals to the
audio steering wheel switch.
STARTING THE SELF-DIAGNOSIS MODE
1. Turn ignition switch from OFF to ACC.
2. Within 10 seconds press and hold the switches “MUTE/ II ” and
“MAP ”simultaneously for 3 seconds.
Then the self-diagnosis operates.
EXITING THE SELF-DIAGNOSIS MODE

Turn ignition switch OFF. Then the self-diagnosis ends.
DIAGNOSIS FUNCTION

It can illuminate all the indicators (LED) in the A/C and AV switch.

It can check for continuity of the switches by sounding the buzzer when the A/C and AV switch is pressed.

It can check for continuity of harness between A/C and AV switch and audio steering wheel switch.
Terminal No. (Wire color) Item Signal
input/
output Condition
Voltag e Example of
symptom
+– Ignition
switch Operation
1 (G/R) Ground Battery power
Supply Input OFF — Battery voltage No sound from
woofer.
2 (B) Ground Ground — ON — Approx. 0 V No sound from
woofer.
5 (P) Ground Amp ON signal Input ACC — Approx. 12 V No sound from
woofer.
7 (W) 8 (B) Woofer sound
signal Input ACC Receive audio sig-
nal No sound from
woofer.
SKIA0177E
PKIB4130E

AUDIO AV-45
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
2. CHECK AMP. ON SIGNAL
1. Connect audio unit connector.
2. Turn the ignition switch ACC.
3. Check voltage between audio unit harness connector M59 ter- minal 12 (G/W) and ground.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace audio unit.
Vehicle Speed Signal InspectionAKS007VI
1. CHECK VEHICLE SPEED OPERATION
Start engine and drive vehicle.
Dose speedometer is operated normally?
Ye s > > G O T O 2 .
No >> Check combination meter trouble diagnosis. Refer to DI-15, "
Trouble Diagnosis" .
2. CHECK HARNESS
1. Turn the ignition switch OFF.
2. Disconnect audio unit connector and unified meter and A/C amp. connector.
3. Check continuity between audio unit harness connector M60 ter- minal 22 (W/L) and unified meter and A/C amp. harness connec-
tor M56 terminal 34 (W/L).
4. Check continuity between audio unit harness connector M60 ter- minal 22 (W/L) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector. 12 (G/W) – Ground : Approx. 12 V
SKIA6818E
22 (W/L) – 34(W/L) : Continuity should exist.
22 (W/L) – Ground : Continuity should not exist.
SKIA6807E