2004 SUBARU FORESTER transmission

4AT(H4SO)-99
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
22 CHECK HARNESS CONNECTOR BETWEEN
INHIBITOR SWITCH AND CHASSIS
GROUND.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from inhibitor
switch.
3) Measure the resistance of harness
between inhibitor switch and chassis ground.
Connector & terminal
(T7) No. 5 — Chassis ground:Is the resistance less than 1
Ω?Go to step 23.Repair the open
circuit in harness
between inhibitor
switch connector
and chassis
ground, and poor
contact in cou-
pling connector.
23 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 1 — (T7) No. 9:Is the resistance less than 1
Ω?Go to step 24.Repair the open
circuit in harness
between TCM and
inhibitor switch
connector, and
poor contact in
coupling connec-
tor.
24 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “P” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 1 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 25.Go to step 65.
25 CHECK INPUT SIGNAL FOR TCM.
1) Position the select lever to any other than
“P” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 1 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
26 CHECK “P” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “P” range indicator light bulb
from combination meter.Is the “P” range indicator light
bulb OK?Go to step 27.Replace the “P”
range indicator
light bulb. IDI-10, Combina-
tion Meter Assem-
bly.>
27 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 1 — (i10) No. 1:Is the resistance more than 1
Ω?Go to step 65.Repair the open cir-
cuit in harness
between TCM con-
nector and combi-
nation meter, and
poor contact in cou-
pling connector.
28 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 1 — Chassis ground:Is the resistance less than 1
MΩ?Go to step 29.Repair the ground
short circuit in “P”
range circuit. Step Check Yes No

4AT(H4SO)-100
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
29 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 3 — (T7) No. 8:Is the resistance less than 1
Ω?Go to step 30.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
30 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “R” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 3 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 31.Go to step 65.
31 CHECK INPUT SIGNAL FOR TCM.
1) Position the select lever to any other than
“R” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 3 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
32 CHECK “R” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “R” range indicator light bulb
from combination meter.Is “R” range indicator light bulb
OK?Go to step 33.Replace the “R”
range indicator light
bulb. 10, Combination
Meter Assembly.>
33 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 3 — (i10) No. 2:Is the resistance less than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM con-
nector and combi-
nation meter, and
poor contact in
TCM connector.
34 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 3 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 35.Repair the ground
short circuit in “R”
range circuit.
35 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 14 — (T7) No. 10:Is the resistance less than 1
Ω?Go to step 36.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector. Step Check Yes No

4AT(H4SO)-101
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
36 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “N” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 14 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 37.Go to step 65.
37 CHECK INPUT SIGNAL FOR TCM.
1) Position the select lever to any other than
“N” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 14 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
38 CHECK “N” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “N” range indicator light bulb
from combination meter.Is the “N” range indicator light
bulb OK?Go to step 39.Replace the “N”
range indicator
light bulb. IDI-10, Combina-
tion Meter Assem-
bly.>
39 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 14 — (i10) No. 3:Is the resistance less than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM con-
nector and combi-
nation meter, and
poor contact in
TCM connector.
40 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 14 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 41.Repair the ground
short circuit in “N”
range circuit.
41 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 4 — (T7) No. 3:Is the resistance less than 1
Ω?Go to step 42.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
42 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “D” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 4 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 43.Go to step 65. Step Check Yes No

4AT(H4SO)-102
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
43 CHECK INPUT SIGNAL FOR TCM.
1) Position select lever to any other than “D”
range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 4 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
44 CHECK “D” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “D” range indicator light bulb
from combination meter.Is the “D” range indicator light
bulb OK?Go to step 45.Replace the “D”
range indicator
light bulb. IDI-10, Combina-
tion Meter Assem-
bly.>
45 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 4 — (i10) No. 11:Is the resistance less than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM con-
nector and combi-
nation meter, and
TCM connector.
46 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 4 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 47.Repair the ground
short circuit in “D”
range circuit.
47 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 5 — (T7) No. 11:Is the resistance less than 1
Ω?Go to step 48.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
48 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “3” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 5 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 49.Go to step 65.
49 CHECK INPUT SIGNAL FOR TCM.
1) Position the select lever to any other than
“3” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 5 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).> Step Check Yes No

4AT(H4SO)-103
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
50 CHECK “3” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “3” range indicator light bulb
from combination meter.Is the “3” range indicator light
bulb OK?Go to step 51.Replace the “3”
range indicator
light bulb. IDI-10, Combina-
tion Meter Assem-
bly.>
51 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 5 — (i10) No. 5:Is the resistance more than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM con-
nector and combi-
nation meter, and
poor contact in
TCM connector.
52 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 5 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 53.Repair the ground
short circuit in “3”
range circuit.
53 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 6 — (T7) No. 4:Is the resistance less than 1
Ω?Go to step 54.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
54 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “2” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 6 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 55.Go to step 65.
55 CHECK INPUT SIGNAL FOR TCM.
1) Position the select lever to any other than
“2” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 6 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
56 CHECK “2” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “2” range indicator light bulb
from combination meter.Is the “2” range indicator light
bulb OK?Go to step 57.Replace the “2”
range indicator light
bulb. 10, Combination
Meter Assembly.> Step Check Yes No

4AT(H4SO)-104
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
57 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 6 — (i10) No. 6:Is the resistance less than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM and
combination
meter, and poor
contact in TCM
connector.
58 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 6 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 59.Repair the ground
short circuit in “2”
range circuit.
59 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B55) No. 7 — (T7) No. 6:Is the resistance less than 1
Ω?Go to step 60.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
60 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Move the select lever to “1” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 7 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 61.Go to step 65.
61 CHECK INPUT SIGNAL FOR TCM.
1) Position the select lever to any other than
“1” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 7 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
62 CHECK “1” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “1” range indicator light bulb
from combination meter.Is the “1” range indicator light
bulb OK?Go to step 63.Replace the “1”
range indicator light
bulb. 10, Combination
Meter Assembly.>
63 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 7 — (i10) No. 7:Is the resistance less than 1Ω? Go to step 65.Repair the open cir-
cuit in harness
between TCM and
combination meter,
poor contact in
TCM connector. Step Check Yes No

4AT(H4SO)-105
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
64 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 7 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 65.Repair the ground
short circuit in “1”
range circuit.
65 CHECK POOR CONTACT.Is there poor contact in inhibi-
tor switch circuit?Repair the poor
contact.Go to step 66.
66 INSPECT INHIBITOR SWITCH.Is the inhibitor switch position
in normal position?Replace the TCM.
Transmission Con-
trol Module
(TCM).>Adjust the inhibi-
tor switch and
select cable. to 4AT-52,
ADJUSTMENT,
Inhibitor Switch.>
Select Cable.> Step Check Yes No

4AT(H4SO)-106
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
H: CHECK HOLD SWITCH
DETECTING CONDITION:
 The LED does not come on when HOLD switch is ON.
 The HOLD switch circuit is open or shorted.
TROUBLE SYMPTOM:
 The 2nd gear is not held.
 Failure of vehicle to start in 2nd gear at “2”, “3”, “D” ranges.
WIRING DIAGRAM:
 LHD model
AT-01834
SBF-4 SBF-1
No.14
IGNITION
SWITCH
i10
i2
B37BATTERY
B55
TCM
19
923
COMBINATION
METER
E
E
B55
1234
56789
10 1112
13 14 15 16 17 18
192021
2223 24
123456
78 9 10 1112
13
14
15 16 17
1819
2021
2223
24
2526
2728
2930
i10
B37
1234
578
910112324
121314
156
16 17 1819
20 2122
16
POWER AND
HOLD SWITCH
3
5
4 HOLD
POWEROFF
532
i3
B38
R92
12
34
56
219
32
B38
1234
5610 11 12 13 14 15716
23 3019 20
22 26 27 28 29817
24 3118
25
20
21
R92
B98R2
B98
HOLD